Samsung SV-DVD440 User manual

DVD-VCR
SV-DVD540
www.samsungvcr.com PAL
EJECT
AUX
OPEN/CLOSE
STANDBY/ON
OK
Instruction Manual

2
GB
Safety Precautions
The mains lead on this equipment is supplied with a
moulded plug incorporating a fuse. The value of the fuse is
indicated on the pin face of the plug. If it requires
replacing, a fuse approved to BS1362 of the same rating
must be used.
Never use the plug with the fuse cover omitted if the cover
is detachable. If a replacement fuse cover is required, it
must be of the same colour as the pin face of the plug.
Replacement covers are available from your dealer.
If the fitted plug is not suitable for the power points in your
house or the cable is not long enough to reach a power
point, you should obtain a suitable safety approved
extension lead or consult your dealer for assistance.
However, if there is no alternative to cutting off the plug,
remove the fuse and then safely dispose of the plug. Do
not connect the plug to a mains socket, as there is a risk of
shock hazard from the bared flexible cord.
IMPORTANT
The wires in the mains lead are coloured in accordance
with the following code: -
BLUE = NEUTRAL BROWN = LIVE
As these colours may not correspond with the coloured
markings identifying the terminals in your plug, proceed as
follows: -
The wire coloured BLUE must be connected to the
terminal marked with the letter N or coloured BLUE or
BLACK. The wire coloured BROWN must be connected to
the terminal marked with the letter L or coloured BROWN
or RED.
WARNING: DO NOT CONNECT EITHER WIRE TO THE
EARTH TERMINAL WHICH IS MARKED WITH THE
LETTER E OR BY THE EARTH SYMBOL , OR
COLOURED GREEN OR GREEN AND YELLOW.
This symbol is intended to alert you to the
presence of dangerous voltage within the
product.
IMPORTANT NOTE
DANGER
This symbol is intended to alert you to the
presence of important instructions
accompanying the product.
This product incorporates copyright
protection technology that is protected by
method claims of certain U.S. patents and
other intellectual property rights owned by
Macrovision Corporation and other rights
owners. Use of this copyright protection
technology must be authorized by
Macrovision Corporation, and is intended
for home and other limited viewing uses
only unless otherwise authorized by
Macrovision Corporation.
Reverse engineering or disassembly is
prohibited.
CAUTION
CAUTION. TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE REAR COVER. NO
USER SERVICEABLE PARTS INSIDE. REFER TO
QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN

3
GB
Contents
◆FOREWORD
■Disc Type and Characteristics .................................................................................................. 6
◆DVD-VCR OVERVIEWS
■Front View of the DVD-VCR ..................................................................................................... 7
■Rear View of the DVD-VCR...................................................................................................... 7
■Infrared Remote Control ........................................................................................................... 8
■Display Indicators...................................................................................................................... 9
■Accessories............................................................................................................................... 9
◆CONNECTING YOUR DVD-VCR
■Deciding How to Connect DVD-VCR........................................................................................ 10
■Connecting DVD-VCR to the TV using the Coaxial Cable........................................................ 11
■Connecting DVD-VCR to the TV using the SCART Cable........................................................ 11
■Connecting DVD-VCR to the Satellite receiver or Other Equipment ........................................ 12
■Connecting the Audio Output Cable ......................................................................................... 13
■Plug & Auto Set Up................................................................................................................... 13
■Tuning Your Television for the DVD-VCR................................................................................. 14
■Deck Control Keys .................................................................................................................... 15
■Basic TV Tuner Operations.......................................................................................................16
◆SETTING UPYOUR DVD-VCR
■Inserting Batteries in the Remote Control................................................................................. 17
■Setting the Date and Time........................................................................................................ 17
■Menu Language........................................................................................................................ 18
■Presetting the Stations Automatically ....................................................................................... 19
■Presetting the Stations Manually .............................................................................................. 20
■Clearing a Preset Station.......................................................................................................... 21
■Changing the Preset Station Table........................................................................................... 22
◆VCR FUNCTIONS
■Setting the DVD-VCR Output Channel ..................................................................................... 23
■Selecting the Colour Mode........................................................................................................ 24
■NICAM ...................................................................................................................................... 24
■Intelligent Picture Control.......................................................................................................... 25
■VideoPlus + Extend................................................................................................................... 26
■Auto Power off .......................................................................................................................... 26
■Screen Messages..................................................................................................................... 27
■Selecting the Cassette Type.....................................................................................................27
■Repeat Play .............................................................................................................................. 28
■S-VHS Play............................................................................................................................... 28
■Selecting the Recording Speed ................................................................................................ 29
■Protecting a Recorded Cassette............................................................................................... 30
■Recording a Programme Immediately ...................................................................................... 30
■Recording a Programme with Automatic Stop.......................................................................... 31
■Using the VideoPlus Feature.................................................................................................... 32
■Modifying VideoPlus Programming........................................................................................... 33
■Using the Timer Programming Feature..................................................................................... 34
■Checking a Preset Recording ................................................................................................... 35
■Cancelling a Preset Recording ................................................................................................. 36
◆PLAYING BACK
■Playing a Cassette.................................................................................................................... 36
■Adjusting Picture Alignment Manually....................................................................................... 36
■Selecting the Audio Output Mode............................................................................................. 37
■Playing a Cassette in Slow Motion ........................................................................................... 37
■Playing a Sequence Frame by Frame ...................................................................................... 38
■Playing a Sequence at Variable Speeds................................................................................... 38
■Searching for a Specific Sequence........................................................................................... 39
■Using the Tape Counter............................................................................................................ 41
■Connecting an RCA Audio/Video Input Cable .......................................................................... 42
■Using the Assemble Edit Function............................................................................................ 43
■Recording from Another VCR or Camcorder ............................................................................ 43

4
GB
Contents (cont.)
◆DVD FUNCTIONS
■ Using the TV Buttons on the Remote Control ............................................................................ 44
■Choosing a Connection........................................................................................................ 45
■Disc Menu Language........................................................................................................... 46
■Audio Language................................................................................................................... 46
■Subtitle Language................................................................................................................ 47
■Dolby Digital Out.................................................................................................................. 47
■MPEG-2 Digital Out ............................................................................................................. 48
■DTS...................................................................................................................................... 48
■Dynamic Compression......................................................................................................... 49
■PCM Down Sampling........................................................................................................... 49
■TV Aspect Ratio................................................................................................................... 50
■Black Level........................................................................................................................... 50
■NTSC Disc Output ............................................................................................................... 51
■DVD Out............................................................................................................................... 51
■Parental................................................................................................................................ 52
■A/V Receiver Connections................................................................................................... 53
■Special Playback Features .................................................................................................. 54
■Disc Menu Navigation.......................................................................................................... 55
■EZ View................................................................................................................................ 55
■Title/Chapter/Time Selection................................................................................................ 57
■Angle View........................................................................................................................... 58
■Subtitle................................................................................................................................. 59
■A to B Repeat....................................................................................................................... 60
■Repeat Chapter/ Title...........................................................................................................61
■Audio.................................................................................................................................... 61
■Marks................................................................................................................................... 62
■MP3/WMA Play....................................................................................................................63
■Program Play & Random Play ............................................................................................ 65
■Picture CD Playback ........................................................................................................... 66
◆Technical Specifications ............................................................................................................. 68
◆SOLVING PROBLEMS
■Problems and Solutions (VCR)............................................................................................ 69
■Troubleshooting Guide (DVD).............................................................................................. 70
Symbols
1 1
☛
➢
Press/push Hold down
= Step number
Important Note
1

Safety Instructions
5
GB
The lightning bolt is a warning sign alerting you to dangerous voltage inside the product.
DO NOT OPEN THE DVD-VCR. Refer to service personnel.
HH
5°C
40°C
10% 75%
THIS DEVICE IS NOT FOR USE IN INDUSTRIAL
ENVIRONMENTS
Do NOT expose the DVD-VCR
to extreme temperature condi-
tions (below 5°C and above
40°C) or to extreme humidity
conditions (less than 10% and
more than 75%).
Do NOT expose the DVD-VCR
to direct sunlight. Do NOT expose the DVD-VCR
to any liquids.
Do NOT place any objects on
the DVD-VCR or remote
control.
During a storm and/or light-
ning, unplug the DVD-VCR
from the mains socket and
aerial.
If the remote control is not
used for a long period of time,
remove the batteries and store
it in a cool, dry place.
The following illustrations represent precautions.

6
GB
Disc Type and Characteristics
This DVD player is capable of playing the following types of discs with the corresponding logos :
* DO NOT play CD-ROM, CD-I and DVD-ROM in this player!
(CDGs play audio only, not graphics.)
* It may not be to play CD-R,CD-RW and DVD-R in all cases due to the type of disc or condition of the recording.
~DIGITAL
SOUND
STEREO
•Playback
Region
Number
•PAL colour
system in U.K,
France, Germany,
etc.
•Dolby
Digital disc •Digital
Audio disc
•Stereo
disc •DTS disc
Disc Markings
Both the DVD player and the discs are coded by region. These regional codes must match in order for the
disc to play. If the codes do not match, the disc will not play.
The Region Number for this player is described on the rear panel of the player.
Playback Region Number
PAL
12 Cm
8 Cm
Single-sided
240 min.
Double-sided
480 min.
Single-sided
80 min.
Double-sided
160 min.
Audio
+
Video
Audio
•DVD contains excellent sound
and video due to Dolby Digital
and MPEG-2 system.
•Various screen and audio
functions can be easily selected
through the on-screen menu.
•An LP is recorded as an analog
signal with more distortion. CD
is recorded as a Digital Signal
with better audio quality, less
distortion and less deterioration
of audio quality over time.
AUDIO-CD 12 Cm
8 Cm
74 min.
20 min.
Disc Types
(Logos) Recording
Types Disc Size Max.
Playing
Time Characteristics
DVD
•NTSC broadcast
system in USA,
Canada, japan,
South Korea, etc.
NTSC

Front View of the DVD-VCR
7
GB
Rear View of the DVD-VCR
EJECT
AUX
VIDEO CASSETTE
COMPARTMENT
AUX VIDEO INPUT JACK
PLAY/STILL BUTTON
EZ VIEW BUTTON
STOP BUTTON
REW /SKIP BACK
BUTTON
RECORD BUTTON
EJECT BUTTON
F.F / SKIP NEXT BUTTON
PROGRAMME SELECTION
BUTTON
OPEN/CLOSE BUTTON
VCR SELECT BUTTON
DVD SELECT BUTTON
DVD DECKSTANDBY/ON BUTTON
AUX AUDIO L, R INPUT JACK
COAXIAL
DIGITAL AUDIO OUT
LINE OUT
OPTICAL
S-VIDEO OUT
L
R
AUDIO
AERIAL IN
CONNECTOR
OUT TO TV CONNECTOR
AV2 (DEC./EXT.) SCART
(EURO-21) SOCKET
AV1 (EURO AV) IN/OUT
SCART (EURO-21) SOCKET
AUDIO L, R OUT SOCKETS
AUDIO L, R OUT SOCKETS
(DVD ONLY)
DIGITAL AUDIO OUT SOCKET (COAXIAL)
VIDEO OUT SOCKET S-VIDEO OUT JACK
DIGITAL AUDIO OUT SOCKET
(OPTICAL)

8
GB
Infrared Remote Control
1STANDBY/ON
2SHUTTLE << / >>
3CLEAR
4DVD
5TV MUTE. AUDIO
6VOLUME +/–
7REWIND
SKIP BACK
8STOP
9SUBTITLE
10 MENU
11 UP
12 LEFT
13 DOWN
14 SPEED
15 RECORD
16 TIMER
17 ANGLE
IPC
18 OPEN/CLOSE
19 0-9
20 TV/VCR
21 VCR, TV SELECT
22 INPUT SEL.
F.ADV/STEP
23 PROG
TRACKING
24 FAST-FORWARD
SKIP NEXT
25 PLAY/STILL
26 INFO.
27 RETURN
28 RIGHT
29 OK
30 EZ VIEW
31 DISC MENU
32 MARK
SEARCH
33 MODE
REPEAT
OPEN/CLOSE
STANDBY/ON
OK
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33

Display Indicators
Accessories
You have just purchased a SAMSUNG Video Cassette Recorder (DVD-VCR).
Together with your DVD-VCR, you will find the following accessories in the box.
OPEN/CLOSE
STANDBY/ON
REMOTE CONTROL
& BATTERIES AUDIO & VIDEO
CABLE
OWNER’S
INSTRUCTIONS
COAXIAL CABLE
STEREO
1 2 3 4 5
6 7 8
1The DVD Deck is active
2A DVD, CD or SVCD is loaded
3The time, counter position, time remaining or
current deck status is displayed
4VHS tape is inserted
5The VCR Deck is active
6A DVD with a DTS soundtrack is loaded
7The Hi-Fi track of a VHS tape is playing
(The current TV show or video is broadcast in
Stereo)
8A Timer Recording is programmed or in progress.
9
GB

10
GB
Deciding How to Connect DVD-VCR
º
You must take into account various factors when connecting audio or video systems:
◆Types of connectors available on your systems
◆Systems connected permanently to the DVD-VCR (satellite receiver for example) or
temporarily (camcorder for example)
Your DVD-VCR is equipped with the following connectors.
Connector Location Type Direction Recommended Use
AV1 (EURO AV) Rear SCART In/Out ◆Television
◆Satellite receiver
◆Other VCR
AV2 IN Rear SCART In ◆Satellite receiver
◆Other VCR
Audio output Rear Audio RCA Out ◆Audio out
AUX Front Aux In ◆Audio in
Audio/Video Video in
VIDEO output Rear RCA Out ◆Video out
S-VIDEO Rear S-JACK Out ◆S-Video out (DVD only)
output
Digital AUDIO Rear Optical Out ◆Digital Audio out (DVD only)
output coaxial
OUT TO TV Rear 75 ΩOut ◆Television
coaxial
IN FROM ANT. Rear 75 ΩIn ◆Aerial
coaxial ◆Cable television network
◆Satellite receiver
☛Whenever you connect an audio or video system to your DVD-VCR, ensure that all elements
are switched off.
Refer to the documentation supplied with your equipment for detailed connection instructions
and associated safety precautions.
L
S-VIDEO OUT
COAXIAL
OPTICAL

11
GB
LINE
Connecting DVD-VCR to the TV using the Coaxial Cable
Connecting DVD-VCR to the TV using the SCART Cable
To receive television programmes a signal must be received from
one of the following sources:
◆An outdoor aerial
◆An indoor aerial
◆A cable television network
◆A satellite receiver
☛Make sure that both the television and the DVD-VCR
are switched off before connecting the cables.
1Remove the aerial or network input cable from the television.
2Connect this cable to the 75Ωcoaxial socket marked on
the rear of your DVD-VCR.
3Plug the coaxial cable supplied into the socket on your
DVD-VCR.
4Plug the other end of the coaxial cable into the connector
previously used for the aerial on the television.
5To obtain better quality pictures and sound on your television,
you can also connect your DVD-VCR to the television via the
SCART cable (see section below) if your television is equipped
with this type of connection.
TV
LINE
3
2
LINE OUT
L
R
AUDIO
You can connect your DVD-VCR to the television using the SCART cable if the appropriate input is
available on the television. You thus:
◆Obtain better quality sound and pictures
◆Simplify the setting up procedure of your DVD-VCR
☛◆Regardless of the type of connection chosen, you must always connect the coaxial cable
supplied. Otherwise, no picture will be visible on the screen when the DVD-VCR is switched off.
◆Make sure that both the television and the DVD-VCR are switched off before connecting the cables.
1Connect the coaxial cable as indicated in the above section.
2Connect one end of the SCART cable to the AV1 (EURO AV) socket on the rear of the DVD-VCR.
3Plug the other end into the appropriate connector on the television.
Aerial
SCART Cable
RF coaxial cable
2
3
TV
TV
4

12
GB
Connecting DVD-VCR to a Satellite Receiver or Other Equipment
1. AV2 IN: By means of 21-pin Scart Cable
Plug the SCART Cable with satellite receiver or other equipment into the AV2 (DEC./EXT.) socket on the rear of
the DVD-VCR.
After making this connection, select the source by pressing the INPUT SEL. button for the AV2 input sources.
2. By means of RF Coaxial Cable
After making this connection, you must preset the station received through the satellite tuner.
RF output channel of the satellite receiver should be adjusted away from channel 60, which is used by the
DVD-VCR, e.g. re-adjust to channel 65.
Satellite Receiver or other Equipment
1. AV1(EURO AV): By means of 21-pin Scart Cable
Plug the SCART Cable with satellite receiver or other equipment into the AV1 (EURO AV) socket on the rear of the
DVD-VCR.
After making this connection, select the source by pressing the INPUT SEL. button for the AV1 input sources.
2. By means of RF Coaxial Cable
After making this connection, you must preset the station received through the satellite tuner.
RF output channel of the satellite receiver should be adjusted away from channel 60, which is used by the
DVD-VCR, e.g. re-adjust to channel 65.
Aerial
Aerial Connector
SCART Cable
RF coaxial cable
1
2
TV
Satellite Receiver or other Equipment
Aerial
Aerial Connector
SCART Cable
RF coaxial cable
12
TV
You can connect your DVD-VCR to a Satellite receiver or other DVD-VCR using the SCART cable if the
appropriate outputs are available on the equipment chosen. The following illustrations give a few
examples of the connection possibilities.

13
GB
Connecting the Audio Output Cable
Plug & Auto Set Up
Your DVD-VCR will automatically set itself up when it is plugged
into the mains for the first time. TV stations will be stored in
memory. The process takes a few minutes. Your DVD-VCR will
then be ready for use.
1Connect the coaxial cable as indicated on page 11.
(Connecting Your DVD-VCR to the TV Using the Coaxial Cable)
2Plug the DVD-VCR into the mains.
3Start the auto scanning.
◆ The number of stations automatically stored by the DVD-VCR
depends on the number of stations that it has found.
4The current time and date are displayed automatically.
Check the date and time.
if it is :
◆ Incorrect, see page 17.
➢Now, you only have to switch the DVD-VCR on and it
is ready for use.
☛Function for “Plug & Auto Set Up” is fixed already.
So if you want to change this fixed one, you can change
it by Presetting the Stations Automatically in OSD “
Auto Setup” menu. (see page 19)
You can connect your DVD-VCR to a Hi-Fi system.
Example: You wish to take advantage of the quality of your Hi-Fi
stereo system when watching a programme or
recording via your DVD-VCR.
☛◆Regardless of the type of connection chosen, you
must always connect the coaxial cable supplied.
Otherwise, no picture will be visible on the screen
when the DVD-VCR is switched off.
◆Make sure that both the television and the DVD-
VCR are switched off before connecting the cables.
1Connect the coaxial cable or SCART as indicated on page 11.
2Plug the audio output cable into the audio connectors on the
rear of your DVD-VCR.
➢Respect the colour coding of the left and right channels.
3Plug the other end of the audio cable into the appropriate input
connectors on your Hi-Fi stereo system.
LINE OUT
L
R
AUD
2
2
COAXIAL
DIGITAL AUDIO OUT
LINE OUT
OPTICAL
L
R
AUDIO
1
LINE O
TV

14
GB
Tuning Your Television for the DVD-VCR
OPEN/CLOSE
STANDBY/ON
2
4
You must tune your television for the DVD-VCR only if you are
not using a Scart cable
➢To view pictures from your DVD-VCR when a Scart
cable is used, the television must be set to the
audio/video mode (AV).
1Switch on the television.
2Switch on the DVD-VCR by pressing STANDBY/ON on the front
of the DVD-VCR or STANDBY/ON on the remote control.
3Select a programme position on the television to be reserved for
use with your DVD-VCR.
4Insert the video cassette in the DVD-VCR. Check that the
DVD-VCR starts reading the cassette; if not, press
❿
II
button.
5Start a scan on your television or set the television to UHF
channel 60.
6Fine tune the television until the pictures and sound are obtained
clearly.
7If you cannot find the pictures and sound, or there is interference
from nearby channels, it may be necessary to change the setting
of the DVD-VCR output channel (see Setting the DVD-VCR
Output Channel on page 23 and Problems and Solutions on
page 69).
8When the picture and sound are perfectly clear, store this
channel at the desired programme position on the television.
Result: That programme is now reserved for use with your
DVD-VCR.

15
GB
Deck Control Keys
The DVD-VCR uses one set of controls to operate both decks.
The following keys are helpful in successfully controlling each
deck.
1STANDBY/ON Button
Press the STANDBY/ON button on the remote control or front
panel to turn on the DVD-VCR.
2DVD Button
Press the DVD button on the remote control when you want to
control the DVD deck.
◆The DVD indicator will light on the Front Panel Display to
show that the DVD deck is selected.
3VCR Button
Press the VCR button on remote control when you want to
control the VCR deck.
◆The VCR indicator will light on the Front Panel Display to
show that VHS deck is selected.
4INPUT SEL. BUTTON
Press the INPUT SEL. button repeatedly to cycle through all of
your input sources, including the Tuner (PR##), AV1 (rear AV
input), AV2 (rear AV input), AUX (front AV input).
•It is only available when VCR deck is selected.
➢Before using the VCR operation of 19~43 pages, press
the VCR button on the remote control to select VCR
mode.
Before using the DVD operation of 45~67 pages, press
the DVD button on the remote control to select and
watch DVD.
1
STANDBY/ON
1
23
4

16
GB
Basic TV Tuner Operations
The following buttons are used when watching television via the
DVD-VCR’s built-in TV tuner.
1TV/VCR Button
Press to switch between your TV’s tuner and the VCR’s internal
tuner.
2PROG Button
Press to change to the next or previous channel.
30-9 Buttons
Press to select channels directly.
4INFO.
Press to display the channel you are watching.
◆Also works in DVD and VCR mode.
1
2
2
3
OK
4

17
GB
Inserting Batteries in the Remote Control
Setting the Date and Time
You must insert or replace the batteries in the remote control
when you:
◆Purchase the DVD-VCR
◆Find that the remote control is no longer working
correctly
1Push the tab in the direction of the arrow to release the battery
compartment cover on the rear of the remote control.
2Insert two AAA, RO3 or equivalent batteries, taking care to
respect the polarities:
◆+ on the battery with + on the remote control
◆–on the battery with –on the remote control
3Replace the cover by aligning it with the base of the remote
control and pushing it back into place.
➢Do not mix different battery types (manganese and
alkaline for example).
Your DVD-VCR contains a 24-hour clock and calendar used to:
◆Automatically stop programme recording
◆Preset your DVD-VCR to record a programme
automatically
You must set the date and time when:
◆You purchase the DVD-VCR
☛◆The time and date are set automatically from the
broadcast signal. If the signal is weak or ghosting
occurs, the time and date may not be set automati-
cally. In this case, they should be set manually.
◆Do not forget to reset the time when you change
clocks from winter to summer time and vice versa.
1After pressing the MENU, press the OK or ❿.
Result: The Setup menu is displayed.
2Press the corresponding  , ❷ buttons to select the Clock
option.
3Press the OK or ❿ to select this option.
Result: The Clock Set menu is displayed.
4Press ➛ or ❿ to select the hour, minutes, day, month and year.
Result: The option selected highlight.
5Press the  or ❷ buttons to increase or decrease the value.
Result: The day of the week is displayed automatically.
➢You can hold the  or ❷ buttons down to scroll more
quickly through the values.
6On completion, press RETURN to exit the menu.
Time Date Year
Clock Set
12 : 00 1 / JAN / 2003 WED
Auto Clock : On
1
Language : English
User Set
Auto Power Off : Off
Screen Messages : On
Install

18
GB
Setting the Menu Language
1 Open “MENU”
After pressing the MENU, press the OK or ❿.
2 Select “Language”
Use the  or ❷ buttons to highlight
“Language,”then press the OK or
❿.
3 Set menu Language
Place the selection arrow next to your desired Language, then
press the OK button.
4Press the  or ❷ buttons to select language you want.
Place the selection arrow next to your desired Language, then
press the OK button.
5On completion, press RETURN to exit the menu.
Language : English
User Set
Auto Power Off : Off
Screen Messages : On
Install
Français
Deutsch
Español
Italiano
Nederlands
Language Set
English
OK
1

Presetting the Stations Automatically
19
GB
VCR
☛You do not need to preset the stations if you have already
set them automatically (see Plug & Auto Set Up on page 13).
Your DVD-VCR contains a built-in tuner used to receive
television broadcasts.
You must preset the stations received through the tuner. This can
be done:
◆Plug & Auto Set up (see page 13)
◆Automatically
◆Manually (see page 20)
You can store up to 80 stations.
1After pressing the MENU, press the OK or ❿.
Result: The Setup menu is displayed.
2Press the corresponding  , ❷ buttons to select the Install
option.
3Press the OK or ❿ to select this option.
Result: The Install menu is displayed.
4Press the corresponding  or ❷ buttons, until the Auto
Setup is selected.
And then press the OK or
❿ to select this option.
Result: A message appears, indicating that any channels
already preset on your DVD-VCR will be deleted.
5Press OK to start the auto scanning.
Result:◆The Please Wait indication highlight on the
television screen.
◆The first frequency band is scanned and the first
station found is displayed and stored.
◆The DVD-VCR then searches for the second
station and so on.
◆When the automatic scanning procedure has
finished, the DVD-VCR switches automatically to
programme 1.
➢The number of stations automatically stored by the DVD-
VCR depends on the number of stations that it has found.
6If you wish to cancel the auto scanning before the end, press
the MENU button to exit the menu.
➢◆The time and date are set automatically from the
broadcast signal. If the signal is weak or ghosting
occurs, the time and date may not be set
automatically. In this case, they should be set
manually (see page 17).
◆Once the auto scanning procedure has finished,
some stations may have been stored more than
once; select the stations with the best reception and
delete the ones no longer required (see page 21).
Auto Setup
Your date will be lost
Press OK to continue
Menu to exit
Auto Setup
Manual Setup
Install
VCR Output CH : CH 60
Language : English
User Set
Auto Power Off : Off
Screen Messages : On
Install
Auto Setup
Please Wait
15%

Presetting the Stations Manually
☛You do not need to preset the stations manually if you
have already set them automatically.
1After pressing the MENU, press the OK or ❿.
Result: The Setup menu is displayed.
2Press the corresponding  , ❷ buttons to select the Install
option.
3Press the OK or ❿ to select this option.
Result: The Install menu is displayed.
4Press the corresponding  or ❷ buttons, until the Manual
Setup option is selected.
5Press the OK or ❿ to select a Manual Setup option.
Result: The TV STATION TABLE menu is displayed.
6Press the  or ❷ buttons to select a programme number as
required.
7Press the ❿ button to preset the station.
Result: The MANUAL TUNING menu is displayed.
8Press the ➛ or ❿ buttons to start scanning channel.
Result: The frequency band is scanned and the first station
found is displayed.
9Press the  or ❷ buttons until the NAME is selected.
The station name is set automatically from the broadcast signal.
10 To change the programme’s name, press the ❿ button.
Result: The first letter of the name flashes.
11 To... Then...
Select a character Press the  or ❷ button until the
in the name required character is displayed
(letters, numbers or “-” character).
Move to the next or Press the ❿ or ➛ buttons
previous character respectively.
12 If you... Then...
Wish to store the ◆ Press the corresponding  or ❷ buttons,
station displayed until the MFT is selected.
◆Press the ➛ or ❿ buttons to adjust the
picture, if necessary.
◆Press OK to store the station
Do not wish to ◆ Press the corresponding  or ❷ buttons,
store the station until the CH is selected.
displayed ◆Press the
➛ or ❿ buttons to go on
scanning the frequency band and display
the next station
◆Go back to the beginning of Step 12
13 Repeat this procedure from Step 6onwards, until all the required
stations have been stored.
14 On completion, press the RETURN button four times to exit the
menu.
20
GB
VCR
Auto Setup
Manual Setup
Install
VCR Output CH : CH 60
Language : English
User Set
Auto Power Off : Off
Screen Messages : On
Install
MANUAL TUNING
PR :
CH : - - -
MFT : -
DECODER : OFF
NAME : - - - -
MEMORY : OK
RETURN
TV STATION TABLE
PR CH NAME DEC
1
2
3
4
5
SWAPPING : OK
DELETE : CLEAR RETURN