Samsung PN42B430P2D User manual

2009 Samsung TV
F/W Upgrade Guide
Samsung Electronics

¾Model List
LCD TV
. LB360 series : LN19B360C5D, LN22B360C5D, LN22B360C8D,
LN26B360C5D, LN32B360C5D
. LB361 series : LN19B361C5D
. LB460 series : LN22B460B2D, LN26B460B2D, LN32B460B2D
. LB530 series : LN32B530P7F, LN32B530P7N, LN37B530P7F
LN40B530P7F, LN40B530P7N, LN46B530P7F
LN46B530P7N, LN52B530P7F
. LB540 series : LN32B540P8D, LN40B540P8F, LN46B540P8F
LN52B540P8F
. LB550 series : LN32B550K1F, LN37B550K1F, LN40B550K1F
LN46B550K1F, LN52B550K1F
. LB650 series : LN19B650T6D, LN22B650T6D
PDP TV
. PB430 series : PN42B430P2D, PN50B430P2D
. PB450 series : PN42B450B1D, PN50B450B1D
. PB530 series : PN50B530S2F, PN58B530S2F
. PB540 series : PN50B540S3F, PN58B540S3F
. PB550 series : PN50B550T2F, PN58B550T2F, PN63B550T2F
. PB560 series : PN50B560T5F, PN58B560T5F

Step1. How to prepare the USB Memory Drive
2. Connect the USB Memory Drive
to the USB port of your PC.
Copy the file into the USB Memory Drive.
3. Go to the USB Memory Drive and then double click the file.
1. Save the firmware file into your computer.
File Name : 2009 DTV S4 firmware.exe
4. Click on the “Unzip” button. 5. Unzipping is in progress.
6. After completing, click on the
“OK” and “Close” buttons.
7. Two folders containing the firmware files
have been added to the USB memory drive.
One is “T-STL3FAUSHC” and
the other is “T-STL5PAUSFC”
8. Safely disconnect the USB memory drive
by right clicking the green check mark
on the taskbar and then left click
“Safely Remove”.
OK

9. Turn your TV on, and then insert
the USB Memory Drive containing
the firmware into the USB port
on the rear of the TV
※Important
If the firmware version you downloaded from the Samsung website
or received from Samsung is older than or has a lower version
number than the version on your TV, do not install it.
10. Press the MENU button to display
the menu. Press the ▲or ▼button
to select “Support”, then press the
ENTER button
11. Press the ▲or ▼button to select
“Software Upgrade”, then press the
ENTER button.
12. The message “Scanning for USB.
It may take up to 30 seconds”
is displayed.
13. Then, the message “Upgrade
Version XXXX to version XXXX?
The system will be reset after
upgrade.” is displayed.
Select “Yes”, then press the ENTER
button.

14. When the software upgrade is
complete; the TV will turn off and
then back on by itself.
Proceed with the ‘Plug & Play’
setup.
15. Once ‘Plug & Play’ is complete;
“Enjoy your watching.” is displayed.
Press the ‘Enter’ key and you are
done.
※Do not pull the USB drive out or
unplug the power cable until
complete
※Important
If the firmware version you downloaded from the Samsung website
or received from Samsung is older than or has a lower version
number than the version on your TV, do not install it.