Samsung PS-37S4A1 User manual

ENG
Infrared Remote Control
➢The performance of the remote control may be affected by bright light.
PICTURE EFFECT SELECTION
PICTURE SIZE/
TELETEXT SIZE SELECTION
MENU DISPLAY/
TELETEXT INDEX
TELEWEB DISPLAY
(DEPENDING ON THE MODEL)
MOVE TO THE REQUIRED
MENU OPTION/
ADJUST AN OPTION VALUE
RESPECTIVELY
TURNS THE PDP ON AND OFF
FASTEXT TOPIC SELECTION
INFORMATION DISPLAY/
TELETEXT REVEAL
TV MODE SELECTION
EXIT TELETEXT
EXIT TELEWEB
(DEPENDING ON THE MODEL)
DIRECT CHANNEL SELECTION
EXTERNAL INPUT SELECTION/
TELETEXT PAGE HOLD
AUTOMATIC SWITCH-OFF/
TELETEXT SUB-PAGE
CONFIRM YOUR CHOICE
(STORE OR ENTER)
NEXT CHANNEL/
TELETEXT NEXT PAGE/
TELEWEB FORWARD
SOUND MODE SELECTION
IF YOUR REMOTE CONTROL IS NOT
FUNCTIONING PROPERLY, TAKE
OUT THE BATTERIES AND PRESS
THE RESET BUTTON FOR ABOUT
2~3 SECONDS. RE-INSERT THE
BATTERIES AND TRY USING THE
REMOTE CONTROL AGAIN.
TruSurround XT
MODE SELECTION
PREVIOUS CHANNEL/
TELETEXT PREVIOUS PAGE/
TELEWEB BACKWARD
PIP FUNCTIONS;
-PIP ACTIVATING OR DEACTIVATING
(PIP ON)
-SWAPPING THE MAIN AND THE SUB
PICTURE (SWAP)
-LOCATION SELECTION (POSITION)
-SOURCE SELECTION (SOURCE)
-SIZE SELECTION (SIZE)
-SCAN
-SELECTING THE CHANNEL OF SUB
PICTURE (P )
MAKE THE REMOTE CONTROL WORKS
FOR TV, VCR, CATV, DVD PLAYER, STB
SOUND EFFECT SELECTION
TELETEXT CANCEL
VOLUME INCREASE
TEMPORARY SOUND SWITCH-OFF
VOLUME DECREASE
TELETEXT DISPLAY/
MIX BOTH TELETEXT INFORMATION
AND THE NORMAL BROADCAST
PICTURE STILL
WHEN YOU PRESS A BUTTON , ‘
’
APPEARS ALONG WITH SELECTED MODE
(TV, VCR, CATV, DVD OR STB) AND
REMAINING BATTERIES ON LCD
VCR/DVD FUNCTIONS;
-REWIND (REW)
-STOP
-PLAY/PAUSE
-FAST FORWARD (FF)
REMOTE CONTROL SETUP
BN68-00707A-00Eng_0806 9/14/04 1:25 PM Page 8

ENG
Connecting to the External Devices
“MONITOR OUT” are used for the equipment with an RGB output, such as
video game devices or video disc players.
Rear of the TV
(Input/Output)
① This end can be fitted with:
◆A SCART connector
◆Three RCA connectors (VIDEO + AUDIO-L/R)
② If you have a second VCR and wish to copy cassettes tape, connect the source VCR to “EXT.1(EXT.2,
EXT.3, AV1 or AV2)”
and the target VCR to “MONITOR OUT” so that you can redirect the signal from
“EXT.1(EXT.2, EXT.3, AV1 or AV2)” to “MONITOR OUT” .
③ When you wish to record a programme, connect the receiver to “EXT.1(EXT.2, EXT.3, AV1 or AV2)”
and the VCR to “MONITOR OUT” so that you can redirect the signal from “EXT.1(EXT.2, EXT.3, AV1
or AV2)”
to “MONITOR OUT” .
or
①
VCR
Decoder /
Video game device
Video disc player
Satellite receiver
DVD
②
③
Input/Output Specification
Connector Input Output
Video Audio (L/R) S-Video RGB Video + Audio (L/R)
EXT.1 ✔✔ ✔✔ Only TV output is available.
EXT.2 ✔✔ ✔ Output you can choose.
EXT.3 ✔✔ ✔ Output you can choose.
BN68-00707A-00Eng_0806 9/14/04 1:31 PM Page 55

ENG
Connecting to the S-Video Input
The S-VIDEO and RCA (AUDIO-L/R) connectors are used for equipment with an S-Video output,
such as a camcorder or VCR.
Rear of the TV
Camcorder
VCR
① To play picture and sound, both the S-VIDEO and RCA connectors must be used.
and
①
☛Whenever you connect an audio or video system to your television,
ensure that all elements are switched off. Refer to the documentation
supplied with your equipment for detailed connection instructions
and associated safety precautions.
BN68-00707A-00Eng_0806 9/14/04 1:31 PM Page 56

ENG
Connecting to the DVI Input
Connecting to the PC Input
The “RGB” (video) and “AUDIO” connectors are used for interfacing with your PC.
Personal Computer
and
Rear of the TV
The “DVI” (video) and “L-AUDIO-R” connectors are used for equipment with a DVI output.
Personal Computer
Rear of the TV
and
BN68-00707A-00Eng_0806 9/14/04 1:31 PM Page 57

ENG
Connecting to the Component Input
① The “COMPONENT 1” connectors are
used for equipment with a DVD output.
(480i/480P/576i/576P/720P/1080i)
② The “COMPONENT 2” connectors are
used for DTV receiver.
(480i/480P/576i/576P/720P/1080i)
DVD
Rear of the TV
DTV receiver
①②
BN68-00707A-00Eng_0806 9/14/04 1:31 PM Page 58

ENG
Connecting and Using the Home Theater System
Connecting the Home Theater System
① Connect the monitoring audio out L, and
R jacks of the MONITOR OUT on the
rear-side connection panel of the PDP
TV to the AUDIO IN jacks of the DVD
Home Theater System (or AV Receiver)
using the audio cable.
② Press the SOURCE button to select the
desired external device connected to the
PDP TV.
③ If you want to hear the sound through
separate speakers, cancel the internal
amplifier.
To Display the DVD Home Theater
! Turn the PDP on and press the SOURCE button to select the Ext.1 (or Ext.2,Ext.3).
@ Be sure to connect the video cable properly if desired external input (Ext.1, Ext.2, or Ext.3)
cannot be selected.
# Play the DVD after activating the DVD Home Theater System.
$ Use the volume control of the Home Theater System while watching the PDP using the DVD
Home Theater, where the PDP TV does not produce the audio.
DVD Home Theater
Rear of the TV
AV Receiver Amplifier
①②
Use the Monitor Out ports of the PDP for Home Theater System Connections.
☛◆Refer to corresponding user’s manual from the manufacturer for wiring the
speakers to the DVD Home Theater System (or AV Receiver).
◆Disable the PDP TV internal speaker to enjoy the rich sound through the
speakers of your Home Theater System.
◆In this case, enjoy the sound from the Home Theater System while the PDP TV
does not produce the audio.
BN68-00707A-00Eng_0806 9/14/04 1:31 PM Page 59