Samsung HG43CU700 Series User manual

Thank you for purchasing this Samsung product.
To receive more complete service, please registeryour product at www.samsung.com
Model Serial No.
HG43CU700** HG50CU700** HG55CU700**
HG65CU700** HG75CU700**
INSTALL GUIDE
English

English - 2
Before Reading This Install
Guide
This TV B2B (Business to Business) model is designed for hotels or the
other hospitality businesses, supports a variety of special functions,
and lets you limit some user (guest) controls.
Figures and illustrations in this Install Guide are provided for
reference only and may differfrom the actual product appearance.
Product design and specifications may change without notice.
Operational Modes
This TV has two modes: Interactive and Standalone mode.
Interactive mode: In this mode, the TV communicates with and is
fully or partially controlled by a connected Set Back Box (SBB) or
Set Top Box (STB) provided by a hospitality System Integration (SI)
vendor. When the TV is initially plugged in, it sends a command
that attempts to identifythe SBB or STB connected to it. If the TV
identifies the SBB or STB and the SBB or STB identifies the TV, the
TV gives full control to the SBB or STB.
Standalone mode: In this mode, the TVworks alone without an
external SBB orthe STB.
The TV has a Hotel Option menu that lets you easily set its various
hospitality functions. Please see page 12.
The menu also lets you activate orde-activate some TV and
hospitality functions so you can create your optimal hospitality
configuration.
Still image warning
Avoid displaying still images (such as jpeg picture files) or still image

stock or news bars or crawls) on the screen. Displaying still pictures
continually can cause uneven screen wear, which will affect image
quality. To reduce the chance that this effect will occur, please follow
the recommendations below:
Avoid displaying the same TV channel forlong periods.
Always try to display a full screen image.
Reduce brightness and contrast to help prevent the occurrence
of after-images.
Use all TV features designed to reduce image retention and
screen burn-in.
Warning! Important Safety
Instructions
Please read the Safety Instructions before using your TV.
Referto the table below foran explanation of symbols which may be
on your Samsung product.
CAUTION
RISK OF ELECTRIC SHOCK. DO NOT OPEN.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). THERE ARE NO USER SERVICEABLE
PARTS INSIDE. REFER ALL SERVICING TO QUALIFIED PERSONNEL.
This symbol indicates that high voltage is present
inside. It is dangerous to make any kind of contact with
any internal part of this product.
This symbol indicates that this product has included
important literature concerning operation and
maintenance.
Class II product: This symbol indicates that a safety
connection to electrical earth (ground) is not required.
If this symbol is not present on a product with a power
cord, the product MUST have a reliable connection to
protective earth (ground).
AC voltage: Rated voltage marked with this symbol is
AC voltage.
DC voltage: Rated voltage marked with this symbol is
DC voltage.
Caution. Consult instructions for use: This symbol
instructs the user to consult the install guide for
further safety related information.
The slots and openings in the cabinet and in the back or bottom
are provided for necessary ventilation. To ensure reliable
operation of this apparatus and to protect it from overheating,
these slots and openings must neverbe blocked or covered.
– Do not place this apparatus in a confined space, such as a
bookcase orbuilt-in cabinet, unless proper ventilation is
provided.
– Do not place this apparatus near orover a radiator or heat
register, orwhere it is exposed to direct sunlight.
– Do not place vessels (vases etc.) containing water on this
apparatus, as this can result in a fire or electric shock.
Do not expose this apparatus to rain or place it near water
(near a bathtub, washbowl, kitchen sink, or laundry tub, in a
wet basement, or near a swimming pool, etc.). If this apparatus
accidentally gets wet, unplug it and contact an authorized dealer
immediately.


Use only a properly grounded plug and wall outlet.
– An improperground may cause electric shock orequipment
damage. (Class l Equipment only.)
To turn off this apparatus completely, disconnect it from the
wall outlet. To ensure you can unplug this apparatus quickly if
necessary, make sure that the wall outlet and powerplug are
readily accessible.
Store the accessories in a location safely out of the reach of
children.
Do not drop or strike the product. If the product is damaged,
disconnect the power cord and contact a Samsung service center.
To clean this apparatus, unplug the power cord from the wall
outlet and wipe the product with a soft, dry cloth. Do not use any
chemicals such as wax, benzene, alcohol, thinners, insecticide,
air fresheners, lubricants, ordetergents. These chemicals can
damage the appearance of the TV orerase the printing on the
product.
Do not expose this apparatus to dripping or splashing.
WARNING - TO PREVENT THE SPREAD OF FIRE,
KEEP CANDLES AND OTHER ITEMS WITH OPEN
FLAMES AWAY FROM THIS PRODUCT AT ALL TIMES.
Use care when touching the TV after it has been
on forsome time. Some parts can be warm to the
touch.
Please contact your local authorities for disposal or recycling
information.
Do not overload wall outlets, extension cords, oradapters beyond
their capacity, since this can result in fire or electric shock.
Power-supply cords should be placed so that they are not likely
to be walked on or pinched by items placed upon or against them.
Pay particular attention to cords at the plug end, at wall outlets,
and at the point where they exit from the appliance.
To protect this apparatus from a lightning storm, orwhen left
unattended and unused for long periods of time, unplug it from
the wall outlet and disconnect the antenna or cable system. This
will prevent damage to the set due to lightning and power line
surges.
Before plugging in the AC power cord of the TV, make sure that
the operational voltage of the TV matches the voltage of your
local electrical powersupply. Referto the powerspecifications
section of the manual orthe power supply label on the product for
voltage and amperage information.
Never insert anything metallic into the open parts of this
apparatus. This may cause electric shock.
To avoid electric shock, never touch the inside of this apparatus.
Only a qualified technician should open this apparatus.
Be sure to plug in the power cord until it is firmly seated. When
unplugging the power cord from a wall outlet, always pull on the
powercord's plug. Neverunplug it by pulling on the power cord.
Do not touch the power cord with wet hands.
If this apparatus does not operate normally - in particular, if
there are any unusual sounds or smells coming from it - unplug
it immediately and contact an authorized dealer or Samsung
service center.
Be sure to pull the power plug out of the outlet if the TV is to
remain unused orif you are to leave the house for an extended
period of time (especiallywhen children, elderly, or disabled
people will be left alone in the house).
– Accumulated dust can cause an electric shock, an electric
leakage, ora fire by causing the power cord to generate
sparks and heat or by causing the insulation to deteriorate.
Be sure to contact an authorized Samsung service centerfor
information if you intend to install your TV in a location with
heavy dust, high or low temperatures, high humidity, chemical
substances, orwhere it will operate 24 hours a day such as in an
airport, a train station, etc. Failure to do so may lead to serious
damage to your TV.

English - 4
Before Reading This Install Guide ---------------------------- 2
Warning! Important Safety Instructions ---------------------------- 2
01 Package Content
Providing proper ventilation foryour TV ---------------------------- 5
Securing the TV to the Wall ---------------------------- 5
Installing the wall mount kit ---------------------------- 6
Wall Mount Kit Specifications (VESA) ---------------------------- 6
Installing the LED TV Stand ---------------------------- 7
02 The Remote Control
About the Buttons on the Remote
Control ---------------------------- 8
03 Initial Setup
Using the TV Controller ---------------------------- 9
04 The Connection Panel
05 Connections
Connecting to your Internet network ---------------------------- 10
Connecting the TVto a SBB or STB ---------------------------- 11
Connecting the Headphone Box ---------------------------- 12
06 Setting the Hotel Option menu
Hotel Option menu items ---------------------------- 
USB Cloning ---------------------------- 17
Settings Cloned in the Hotel Option
Menu ---------------------------- 18
Setting Auto Initialize ---------------------------- 19
Updating the TV’s Software ---------------------------- 22
07 Editing Channels
Using Channel Editor ---------------------------- 22
08 Specifications and OtherInformation
Specifications ---------------------------- 24
Environmental Considerations ---------------------------- 24
Decreasing power consumption ---------------------------- 24
Supported Resolutions for Connecting a
Computer ---------------------------- 25
Supported Resolutions forVideo Signals ---------------------------- 26
Supported Resolutions for UHD Input
Signals ---------------------------- 26
Read Before Using the Internet Function ---------------------------- 27
Dimensions ---------------------------- 27
Licenses ---------------------------- 28
Important Warranty Information
Regarding Television Format Viewing ---------------------------- 29
SAMSUNG ELECTRONICS NORTH
AMERICAN LIMITED WARRANTY
STATEMENT ---------------------------- 29
Contents

English - 5
01 Package Content
Make sure the following items are included with your TV. If any items
are missing, contact your dealer.
Remote Control & Batteries
(AAA x 2) Power Cord
Quick Setup Guide / Regulatory
Guide
Data Cable x 2
(Depending on the model)
The items’ colors and shapes mayvary depending on the models.
Cables not included can be purchased separately.
Check for any accessories hidden behind or in the packing
materials when opening the box.
The screen can be damaged from direct pressure when
handled incorrectly. As shown in the figure, make sure to
grip the edges of the screen whenyou lift the TV.
Do Not Touch
This Screen!
Providing properventilation for your TV
When you install your TV, maintain a distance of at least 4 inches (10
cm) between the TV and other objects (walls, cabinet sides, etc.) to
ensure properventilation. Failing to maintain properventilation may
result in a fire or a problem with the product caused by an increase in
its internal temperature.
When you install your TV with a stand or a wall mount, we strongly
recommend you use parts provided by Samsung Electronics
only. Using parts provided by another manufacturermay cause
difficulties with the product or result in injury caused by the
product falling.
Securing the TV to the Wall
Caution: Pulling, pushing, or climbing on the TV may
cause the TV to fall. In particular, ensure your children
do not hang on or destabilize the TV. This action may
cause the TV to tip over, causing serious injuries ordeath.
Follow all safety precautions provided in the Safety Flyer
included with your TV. For added stability and safety, you
can purchase and install the anti-tip device.
Preventing the TV from falling
1. Using the appropriate screws, firmly fasten a set of brackets to
the wall. Confirm that the screws are firmly attached to the wall.
– You may need additional material such as wall anchors
depending on the type of wall.
2. Using the appropriately sized screws, firmly fasten a set of
brackets to the TV.
– Forthe screw specifications, refer to "Wall Mount Kit
Specifications (VESA)" in the table on page 6.
3. Connect the brackets fixed to the TV and the brackets fixed to
the wall with a durable, heavy-duty string, and then tie the string
tightly.
– Install the TV near the wall so that it does not fall backwards.
– Connect the string so that the brackets fixed to the wall are
at the same height as or lowerthan the brackets fixed to
the TV.
Wall-anchor
(not supplied)
The displayed image may differ from your TV, depending on the model.

English - 6
– Forwall mounts that do not complywith the VESA standard
screw specifications, the length of the screws may differ
depending on the wall mount specifications.
– Do not fasten the screws too firmly. This may damage the
product or cause the product to fall, leading to personal
injury. Samsung is not liable forthese kinds of accidents.
– Samsung is not liable forproduct damage or personal injury
when a non-VESA or non-specified wall mount is used or the
consumerfails to follow the product installation instructions.
– Do not mount the TV at more than a15 degree tilt.
– Always have two people mount the TV onto a wall.
TV size in
inches
VESA screw hole
specs ( * ) in
millimeters
(inches) (inches) (inches)

200 x 200
14.9  
50 17.9 5.9 11.5
55 20.2 8.1 11.8
65  20.6 8.9 11.9
75 400 x 400 25.0 9.1 12.8
TV size in
inches C (mm)Standard Screw Quantity

20-22 M8 4
50
55
65
75
Do not install yourwall mount kit while your TV is turned
on. This may result in personal injuryfrom electric shock.
Installing the wall mount kit
You can mount the TV on the wall using a wall mount kit (sold
separately).
TVWall mount
bracket
C
The Product shape may differ depending on the model.
The wall mount kit (sold separately) allows you to mount the TV on
a wall.
Fordetailed information on installing the wall mount, see the
instructions provided with the wall mount. Contact a technician
forassistance when installing the wall mount bracket. Samsung
Electronics is not responsible for any damage to the product orinjury
to yourself or others if you select to install the TV on yourown.
Wall Mount Kit Specifications (VESA)
Install your wall mount on a solid wall perpendicular to the floor. If
you are attaching the wall mount to building materials otherthan
plaster board, contact your nearest dealer. If installed on a ceiling or
slanted wall, the TV may fall and cause severe personal injury.
The wall mount kit is not supplied, but sold separately.
NOTE
– Standard dimensions for wall mount kits are shown in the
table below.
– Samsung wall mount kits contain a detailed installation
manual. All parts necessary for assembly are provided.
– Do not use screws that do not comply with the VESA
standard screw specifications.
– Do not use screws that are longer than the standard
dimension or do not complywith the VESA standard screw
specifications. Screws that are too long may cause damage
to the inside of the TV set.

English - 7
Installing the LED TV Stand
Assembling the Stand and Components
When installing the stand, use the provided components and parts.
Stand Power Cord
1
R
2 3
43″
75″
50-65″
4
NOTE
Make sure to distinguish between the front and back of each component when assembling them.
Make sure that at least two persons lift and move the TV.

English - 8
02 The Remote Control
About the Buttons on the Remote
Control
The images, buttons, and functions of the remote control may
differwith the model orgeographical area.
If you use the remote control that comes with yourTV to control
another TV, some functions may not operate normally.
A button without a description in the image below is not
supported on the product.
2
1
3
Alkaline batteries are recommended for longer battery life.
(Power)Press to turn the TV on oroff.
(Settings - Number
- Option button)
Each time you press this button, Settings menu
/ virtual numeric pad / Option pad are displayed
alternately.
Use this button to access additional options
that are specific to the feature in use.
Press to bring up the virtual numeric pad
on the screen. Use the numeric keypad to
enter numeric values. Select numbers and
then select Done or Enter Number to enter
a numeric value. Use to change the channel,
enter a PIN, ZIP code and etc.
(Color button) When pressed, colored buttons appearon the
screen. Use this button to access additional
options that are specific to the feature in use.
1Select Selects or runs a focused item. When pressed
while you are watching content, detailed
program information appears.
2Directional button
(up/down/left/right)
Use to navigate the menu or move the focus to
highlight items on the Home Screen.
(Volume)Move the button up or down to adjust the
volume. To mute the sound, press the button.
When pressed for 2 seconds or more, the
Accessibility Shortcuts appears.
(Channel)Move the button up or down to change the
channel. To see the Guide screen, press the
button. When pressed for1 second or more, the
Channel List screen appears.
Press and hold the button up or down to quickly
change the channel.
(Return)Returns to the previous menu. When pressed
for1 second or more, the running function
is terminated. When pressed while you are
watching a program, the previous channel
appears.
(Play/pause) When pressed, the playback controls appear.
Using these controls, you can control the media
content that is playing.
(Smart Hub)Press to switch to the Home Screen.
3Launch app button Launch the app indicated by the button.
Available apps may differdepending on the
geographical area or contents provider.
Fire orexplosion may occur, resulting in damage to the remote control or personal injury.
Do not apply shock to the remote control.
Be careful not to let foreign substances such as metal, liquid, or dust come in contact with the charging terminal of the remote
control.
When the remote control is damaged or you smell smoke or burning fumes, immediately stop operation and then repair it at the
Samsung service center.
Do not arbitrarily disassemble the remote control.
Be careful not to let infants orpets suck or bite the remote control. Fire or explosion may occur, resulting in damage to the
remote control or personal injury.

English - 9
03 Initial Setup
When you turn on your TV forthe first time, it immediately starts the
Initial Setup. Follow the instructions displayed on the screen and
configure the TV's basic settings to suit your viewing environment.
If you already completed the Initial Setup, run the Initial Setup again
using the following menu.
Hotel Option menu > System > TV Reset
If you select TV Reset, the TV resets all values to their factory defaults.
When the TV turns off, press the Power button on the remote control
to turn on the TV. The TV starts the Initial Setup.
1
Select the region settings
Before select region, refer to the country list information on
the right.
If you select the incorrect region, execute TV Reset again after
the Initial Setup is completed.
If the region is changed, the TV automatically turns off and on.
2
Selecting yourTV installation type
TV Basic Setup: Select to proceed to the next step to set the
basic options for using your TV.
Cloning Mode: Copy the system settings from the USB or server
to the TV.
Factory Menu: End Initial Setup and go to Hotel Option menu
directly.
Follow the instructions on the screen to configure the settings for
your own viewing environment.
Using the TV Controller
You can turn on the TV with the TV Controller button at the bottom
of the TV, and then use the Control menu. The Control menu appears
when the TV Controller button is pressed while the TV is On. Formore
information about its usage, referto the figure below.
The screen may dim if the protective film on the SAMSUNG
logo orthe bottom of the TV is not removed. Please remove the
protective film.
Control menu
:Power On/Off
:Channel Up
:Channel Down
:Volume Up
:Volume Down
:Source
TV Controller button / Remote control sensor
Short Press: Move
Long Press & Hold: Select
The TV Controller button is located on the bottom of the TV.
04 The Connection Panel
⑧
⑦
①
④
②
⑤
⑥
③
BACK OF TELEVISION
* EX-LINK: Dedicated to service technicians.
When connecting an external device, match the colorof the
connection port to the cable.
Wheneveryou connect an external device to your TV, make sure
that poweron the TV and the device is turned off.
①USB (5V 0.5A), USB (HDD 5V1A)
– Connectorforsoftware upgrades and Media Play, etc.
– Service connection.
②HP-ID
Connect the cable to HP-ID and Headphone Jack simultaneously
and connect it to separated Headphone Box. See page 12. When
connecting Headphone to Headphone Box, it works same as
Headphone function.
③HEADPHONE JACK
Headphones may be connected to the headphone jack on your TV.
While the headphones are connected, the sound from the built-in
speakers is disabled.
④HDMI IN 1, 2, 3 (eARC )
Connects to the HDMI jack of a device with an HDMI output.
– No separate sound connection is needed for an HDMI to HDMI
connection. HDMI connections carry both audio and video.
– It is recommended that the external device of the HDMI

compatible problem like no sound or the abnormal screen
or etc with the device of the HDMI 1.2 version, contact to the
Samsung customercare center.

English - 10
⑤DATA
– Used to support data communication between the TV and the
SBB or STB.
– Connects using RJ-12 TV type plugs.
⑥ANT IN
To viewtelevision channels correctly, the TV must receive a signal
from one of the following sources:
– An outdoorantenna / A cable television system
⑦DIGITAL AUDIO OUT (OPTICAL)
Connects to a Digital Audio component.
⑧LAN
To connect a LAN cable, use a CAT 7 (*STP type) cable for the
connection. (100/10 Mbps)
* Shielded Twisted Pair
05 Connections
Connecting to your Internet network
You can set up your TV so that it can access the SMART TV applications
through your local area network (LAN) using a wired orwireless
connection.
Afteryou have physically connected the TVto yournetwork, you
must configure the network connection to complete the process.
You can configure the connection after the Initial Setup process,
through the TV’s menu (Hotel Option menu > Smart Service >
Network Setup > (Open Network Settings > Wireless or Wired)).
Establishing a wireless Internet connection
Connect the TVto the Internet using a wireless access point or
modem.
Wireless IP access point or
modem with a DHCP Server
LAN Cable (Not Supplied)
The LAN Port on the Wall
This TV supports the IEEE 802.11 a /b /g /n /ac communication
protocols. Samsung recommends using IEEE 802.11n. Otherwise,
when you play video over a network connection, the video may
not play smoothly.
– Some of the IEEE 802.11 communication protocols may not
be supported depending on the model orgeographical area.
To use a wireless network, the TV must be connected to a wireless
access point ormodem. If the wireless access point supports
DHCP, the TV can use a DHCP or static IP address to connect to the
wireless network.
Select a channel that is not currently in use for the wireless access
point. If the channel set for the wireless access point is currently
being used by another device, the result is usually interference or
a communications failure.
Most wireless networks have an optional security system. To
enable a wireless network's security system, you need to create
a security key using characters and numbers, and then enterthat
key into the access point through its menu. You then must enter
this security key into any other devices you want to connect to the
wireless network.

English - 11
Connecting the TV to a SBB or STB
ETH MODEM
TV Rear Panel
STB (SBB)
Data Cable
Connect the DATA port of the TV to the ETH MODEM port of the STB
(SBB) with the Data cable.
The ETH MODEM port name that you connect the Data Cable to
may differ depending on the SBB or STB type.
IR signals sent by the remote control to the TV or SBB / STB must
meet the following specification to use IR pass through function.
IR signal receiver specification
– Band pass filter center frequency:  ㎑
– Carrier Frequency, Duty 50%
– 
– Minimum Gap Time Between the burst (tburst gap): 16
pulses (422 us)
– Minimum Gap Time between the data commands (tpause):
25 ㎳
List of Hospitality SI Vendors and compatible data
cables supplied with the TV
Confirm you are using the correct data cable foryour SI vendor.
Referto the code label on the data cables.
Contact your nearest dealer oryour SI Vendorto buy the data
cable not included in the TV.
1
6
1
2
3
4
5
Confirm the code on the Code Label.
TV side STB (SBB) side
Cable code Pin assign REMARK

(Color: BLACK)
TV SIDE
1: NC
2: RX
3: TX
4: IR
5: GND
STB (SBB) SIDEP1 P2
31
52
63
14
25
1: IR
2: GND
3: NC
4: NC
5: RX
6: TX
RED
GREEN
WHITE
BLACK
YELLOW
SAMSUNG
and others

(Color: LIGHT
GRAY)
TV SIDE
1: CLK
2: RX
3: TX
4: IR
5: GND
P1 P2
61
52
33
14
25
1: IR
2: GND
3: TX
4: NC
5: RX
6: CLK
RED
GREEN
WHITE
BLACK
YELLOW
STB (SBB) SIDE
MTI
RX and TX notation is based on TV.

Network Security Protocols
The TV only supports the following wireless network security
protocols:
Authentication Modes: WEP, WPAPSK, WPA2PSK
Encryption Types: WEP, TKIP, AES
In compliance with the Wi-Fi certification specifications, Samsung TVs
do not support WEP or TKIP security encryption in networks running
in the 802.11n mode.
If the wireless access point supports WPS (Wi-Fi Protected Setup),
you can connect the TV to your network using PBC (Push Button
Configuration) or a PIN (Personal Identification Number). WPS
automatically configures the SSID and WPA key settings.
Your Smart TV cannot connect to uncertified wireless access point.
Establishing a wired Internet connection
There are three main ways to connect the TV to your network using
cable, depending on your network setup. They are illustrated below:
The Modem Port on
the Wall
Modem Cable (Not Supplied) LAN Cable (Not Supplied)
TV Rear Panel
External Modem
(ADSL / VDSL / Cable TV)
TV Rear Panel
The Modem Port on the Wall
Modem Cable
(Not Supplied)
LAN Cable
(Not Supplied)
LAN Cable
(Not Supplied)
External Modem
(ADSL / VDSL / Cable TV)
IP access point that
has a DHCP Server
TV Rear Panel
The LAN Port on the Wall
LAN Cable (Not Supplied)
The TV will not be able to connect to the Internet if your network
speed is below10 Mbps.
To connect a LAN cable, use a CAT 7 (*STP type) cable for the
connection. (100/10 Mbps)
* Shielded Twisted Pair

English - 12
Connecting the Headphone Box
You can connect the Headphone box using the following method.
Audio Loop in
An additional Headphone Box can be installed on a bed or business
desk foradded convenience. The installation procedures are given
below.
Detailed Drawing of the Headphone Box.
TV Rear Panel
Headphone Box
"The rearpanel may differ depending on the model.
1
2
4
5
3
6
7
Shield wire
Red Wire (Audio-R)
HP-ID
Headphone
Red wire + White wire
Headphone Box
White wire (Audio-L)
Shield Wire
06 Setting the Hotel Option
menu
To access the Hotel Option menu, press the following buttons on the
remote control:
1. Press the button.
2. Press the up directional button.
3. Press the down directional button.
4. Press the Select button.
To control the TV functions in the Hotel Option menu, the TV has the
Standalone mode.
SI Vendor: OFF / SSCP
Aftera menu appears, followthese general directions to navigate and
change values:
Use the directional buttons on the remote control to move from
menu item to menu item.
Press the Select button on the remote control to select a menu
item. The screen displays that menu item only.
Press the left or right directional button to change a value. The
right directional button increases numerical values. The left arrow
button decreases numerical values.
When the screen is displaying one menu item, you can press the
up or down directional button to display the next or previous
menu item.
Press the button to exit the current menu item and go to a
higher menu level.
To exit a Hotel Option menu, turn off the TV, and then turn it on
again. Any changes you made are saved except changes to SI
(System Integration) vendor. Forchanges to SI vendor, you must
turn the TV off, wait until the power indicatorat the bottom of the
TV glows steadily. And then unplug the TV's power cord, wait for
the powerindicator to go off, and then plug the TV's powercord
in again.


Hotel Option menu items
To exit from this menu, turn off the TV, and then turn on again. Any
changes you made are saved.
The menu items may not be supported depending on the models.
Hotel Option menu Item Description
Hospitality Mode
Select Hospitality Mode.
Interactive: TVworks with an SI STB or SBB.
Standalone: TVworks alone, without an SI STB or SBB.
SI Vendor
Interactive: Samsung / OCC / MTI / Nstreams / Enseo / Cardinal /
Guestek / Seachange / MDC / Innvue
Standalone: Off / SSCP
SI Config
MDC ID Settings This function is only available when set to
Hospitality Mode: Interactive, SI Vender: MDC.
Power On
Power On Channel Set the channel to displaywhen the TV is turned
on.
User Defined: Lets you set the channel
number manually on Power On Channel
Num. See PowerOn Channel Num below.
Last Saved: If you select this item, when the
TV is turned on, it displays the channel it
was displaying when it was turned off.
PowerOn Channel Num When the TV is turned on, it switches
automatically to this channel.
PowerOn Channel Type Select the type of the channel will be displayed
when the TV is turned on.
ATV (analog air band), DTV (digital air band),
CATV (analog cable band), CDTV (digital cable
band), IPTV (IP channel, IPTV is set when
deployed from solution.)
Power On Volume Set volume level when the TV is turned on.
User Defined: Lets you set volume level
manually.
Last Saved: When the TV is turned on, it
returns to the volume that had been set
when the power had been turned off.
Power On Volume Num The TV turns on with set volume level in
Standalone mode.
Min Volume The minimum volume level the user can set in
Standalone mode.
Max Volume The maximum volume level the user can set in
Standalone mode.
Power On Source Select the input source to be displayed when the
TV is turned on.
Hotel Option menu Item Description
Power On Option Determines the TV's state when power returns
after a power failure orafteryou have unplugged
the TV and then plugged it in again.
Power ON: When the powerreturns, the TV
turns on.
Standby: When the powerreturns, the TV
enters the standby mode.
Last Option: Returns to its last power state.
If it was in standby mode, it returns to
standby mode. If it was on, it turns on.
Channel
Channel setup Gives you direct, immediate access to some
of the channel menu functions on the
Broadcasting menu such as Audio Options, Auto
Program etc.
Channel Editor Lets you edit the channels stored in the TV's
memory.
Change the channel numbers and names,
manage genre and language groups and
delete channels.
Apply the Screen Off to channels you select.
The Screen Off blanks out the video from a
channel and outputs only audio.
Lets you view information about each
channel easily, without your having to
display each channel directly.
Mixed Channel Map Enables showing/browsing all antenna type
(Air/Cable) channels at the same time.
ON: When set to on, guests can access the
complete channel map irrespective of the
selected antenna type. The Channel List/
Channel Editor will also populate Airas well
Cable type channels.
OFF: When set to off, guest can access the
channel map corresponding to the selected
antenna type (Air/Cable) only. The Channel
List/Channel Editor will only show the
selected antenna type channels.
Dynamic SI ON: Do not check the DTV program channel
number.
OFF: Check the DTV program channel
number.
MyChannel Enable or disable the MyChannel function.
This function is available when set to
Hospitality Mode: Standalone.
ON: Let hoteliers set Language and genre
forthe channels provided by the hotel to
display the corresponding channel when
user choose language and genre.
OFF: Disable MyChannel mode.

English - 14
Hotel Option menu Item Description
Headphone Management
HP Mode ON: When the Headphone is connect to the
TV, allows you to listen to audio through
the TV's speakerand the connected
headphones simultaneously. But, you can
only adjust the volumes of TV speaker.
OFF: When the Headphone is connect to the
TV, allows you to listen to audio through the
connected headphones only.
Default HPVolume Configure the values of headphone's volume
when HP MODE is set to ON.
Main Speaker ON: Plays the TV sound through the TV
speaker.
OFF: Plays the TV sound through the
headphones only.
Power and Energy Saving
Brightness Reduction ON: Turns on the energy saving function.
OFF: Turns off the energy saving function.
Cloning
Clone TV to USB Clone the current TV options to a USB device.
Clone USB to TV Clone the saved TV options on a USB device to
the TV.
Setting Auto Initialize If you set Setting Auto Initialize to On, the TV
menu items are restored again to theirvalues
cloned initiallywhen the TV turns off and then
on.
Hotel Option menu Item Description
Menu OSD
Picture Menu Lock ON or OFF the Picture menu.
Menu Display ON: The main menu is displayed.
OFF: The main menu is not displayed.
Channel Menu Display ON: Broadcasting menu is enable forguest.
OFF: Broadcasting menu is disable for
guest.
Panel Button Lock Turning the TV Controller button operations
on or off.
Unlock: Unlocks TV Controller button.
Lock: Locks TV Controller button.
OnlyPower: Locks TV Controller button
except the power off function.
Clock
Local Time Select the way to update the clock data
Standalone: Manual / Time Channel
Interactive: Manual / Auto / Time Channel
– Manual: The clock is set manually by the
userwhen the TV is in Standalone mode.
– Auto: The clock is set automaticallywhen
the TV is in Interactive mode.
– Time Channel: The clock is set from the
selected channel.
Time Channel Type Select the type of the channel to update the
clock data.
DTV (digital air band), CDTV (digital cable band),
SDTV
This function is only available Local Time set
to Time Channel.
Time Channel Num Select the number of the channel to update the
clock data.
This function is only available Local Time set
to Time Channel.
External Source
USB Pop-up Screen When USB is connected to the TV :
Automatic: This enters the USB content
menu automatically.
Disable: Neither the popup window nor the
menu appears.
External Source Banner If set to On, the TV displays the External Source
Banner (information) when you change the TV
source to another external input, press the Info
key, or turn the TV on.
ON: The External Source information is
displayed on the TV screen.
OFF: The External Source information is not
displayed on the TV screen.
Anynet+Return Source Select the return TV source after stopping an
Anynet+ (HDMI-CEC) connection. (This function
is especially useful for the Guestlink RJP.)

English - 15
Hotel Option menu Item Description
IGMPversion The level in which the device is connected in the
Network switch.
AUTO: Network switch is will connected
automatically to available IGMPversion.
V2: Network switch is will connected to
IGMP version 2.
V3: Network switch is will connected to

Security
Factory Lock Disable entry to Hotel Option menu.
ON: The password is needed before entering
Hotel Option menu.
OFF: Disable this function.
Password Popup Enable or disable password input popup
window. If this option is set to off, the TV will not
display the password input popup windowwhen
entering the Hotel Option menu. If set to ON,
the password input popup window appears.
Password Input If this function is enabled, the password input
popup window appears which asks foran
8-character security password. The admin
must enter a password before applying or
updating security preferences. After the correct
password is entered, options such as Password
Setting, Password Reset and Security Mode are
available.
Password Setting User can change the password.
Password Reset Password is reset to "00000000."
Security Mode Provides password protected administrative
functionality to enable or disable features of
hospitality TV, such as USB, HDMI. To use this
option, Security Mode set to ON. After Security
Mode set to ON, options such as USB, HDMI are
automatically enabled.
USB Enable or disable USB access. If this function is
set to Disable, access to USB media is blocked.
Clone USB to TV and TV Reset will be disabled in
the Hotel Option menu.
HDMI Enable or disable HDMI access. If this function
is set to Disable, Anynet+, HDMI source, HDMI
type external channels will not be accessible
to the user.
Hotel Option menu Item Description
Smart Service
Network Setup Run the Network menu to configure your TV's
network settings. You can set the following
items:
Network Status: View the current network
and Internet status.
Open Network Settings: Connect to an
available network.
Reset Network: Restore the network
settings to the factory default.
Expert Settings: Configure advanced
network settings.
Download by App ID Enterthe App ID. Only a registered ID can be
entered.
Apps Editable Provide a way to enable or disable the Apps and
Notification Settings menu.
ON: Enable the Apps and Notification
Settings menu.
OFF: Disable the Apps and Notification
Settings menu.
Ambient Editable Provide a way to enable or disable the Ambient
Settings menu in Ambient Mode.
ON: Enable the Ambient Settings menu.
OFF: Disable the Ambient Settings menu.
Terms & Policy Viewthe entire text of the Terms & Policy
document.
You must agree to the Smart Hub service
agreement.
Smart Features Run the Start Screen Option menu.
Start with Smart Hub Home: Automatically
display Smart Hub when the TV is turned on.
Autorun Last App: Automatically launch the
last used application when TV is turned on.
Autorun Multi View Mirroring: Multi View
runs automatically when you mirroryour
mobile screen.
Quick Settings Editor Edit the items to be displayed in Quick Settings
and change their order.
Samsung Account Create and manage your own Samsung account.
Service Discovery Used to block orunblock 'universal plug and
play' protocol communications.
ON: Unblock the universal plug and play
protocol.
OFF: Block the universal plug and play
protocol.

English - 16
Hotel Option menu Item Description
OTN Update Lets you upgrade the TV Software over the
network when a valid upgrade file is present
on server.
OTN Update changed to ON and disabled
when Enrollment Status in LYNK Cloud
is Yes.
SW Update Lets you upgrade the TV Software with a USB
device.
Remote Management Allow the Samsung Call Centerto remotely
access and troubleshoot your TVwhen you need
assistance.
About This TV Display the Samsung website, and product and
software information.
Standby LED When the TV is in standby mode, you can
configure the settings of the powerindicator.
ON: The LED is on.
OFF: The LED is off.
TV Reset Returns all settings on the TV to theirfactory
defaults.
LYNK Cloud
Enrollment Lets you enroll the TVwith LYNK Cloud solution.
Enrollment Status Check the status of the TV enrollment in the
LYNK Cloud service.
*Virtual Standby
Virtual Standby Mode When the AC powercord is plugged in and
the poweris off, this option maintains the TV's
important features even afterthe screen is off.
Electricity consumption may vary
depending on the environment.
Reboot Time After the TV poweris off (in Virtual Standby
Mode) if there is no input from the userwithin
the set Reboot Time, the TVwill reboot and
enter Virtual Standby Mode again.
Room Number
You can set the room numberof the TV's location.
*: This function is available when Enrollment Status in LYNK
Cloud is set to ON.
Refer to the manual of each solution for details about functions
and settings of the solutions such as LYNK Cloud.
Hotel Option menu Item Description
DRM
DRM Mode Configures DRM support.
OFF: Turns off DRM support.
LYNK DRM: Select to turn on LYNK CAS
support only.
Pro:idiom: Select when there are any
Pro:Idiom channels.
LYNK DRM, PI: Select when there are
LYNK-DRM and Pro:Idiom channels at the
same time.
System
Self Diagnosis for HTV Lets you check the state of Pro:Idiom and
its communication with the SI STB or SBB. If
you have any problems with the Pro:idiom
encryption channel orthe communications
with the SI STB or SBB, use this diagnosis
function. If PI DTV Channel Key Loss (Pro:Idiom
DTV Channel Key Loss) appears to have failed
and the Pro:Idim encryption channel has failed
to play content, first check the broadcasting
systems related to Pro:Idiom encryption. If
your broadcasting system does not have a
problem, contact Samsung Service. If STB SI
Vendor Setting appears to have failed and
communication with the SI STB or SBB has
failed, first check your SI STB or SBB. If your SI
STB or SBB does not have a problem, contact to
Samsung Service.
Self Diagnosis for TV Run the Device Care menu.
Video Test: Use this test when you
experience a problem with yourTV's video.
Smart Hub Connection Test: Use this test
when you experience a problem with your
TV's smart hub.
HDMI Troubleshooting: Use this test when
you experience a problem with your TV's
HDMI connection.
Start Picture Test: Use this test when you
experience a problem with yourTV's picture.
Start Sound Test: Use this test when you
experience a problem with yourTV's sound.
Signal Information: Show digital
broadcasting signal information.
Reset Smart Hub: Reset the Smart Hub
and Samsung account settings stored on
your TV.
System Manager Gives you direct, immediate access to System
Manager functions such as Time, Language,
Change PIN.
System Manager allow you to adjust your TV's
system and customize settings foryourviewing
environment.

English - 17
USB Cloning
Hotel Option menu > Cloning
The USB cloning function lets you download user-configured settings
(Picture, Sound, Broadcasting, and Hotel Option menu) from one TV
to a USB device, and then upload these settings from the USB device
to other TV sets. This lets you create a standard file of settings and
distribute that standard file to all the TVs in yourfacility.
After cloning, certain features are applied when the TV is turned
on again.
Cloning TV to USB: Copies stored menu settings from
a TV to a USB device
Hotel Option menu > Cloning > Clone TVto USB
1. Insert a USB device into the USB port on the rearof the TV.
2. Go to the Hotel Option menu.
3. Press the up ordown directional button to select Clone TV to USB,
and press the Select button on the remote control.
4. The cloning message is displayed.
– The clone folderwill be labeled T-NKLCAKUC.
– The cloned values include the values on the guest side menu
(Picture, Sound, Broadcasting and so on) and the Hotel Option
menu.
Cloning USB to TV: Copies menu settings and channel
data in a USB device to a TV
Shortcut: Turn the TV off, insert the USB device, turn the TV on, and
then press the Select button on the remote control for5 seconds.
To clone data to the TV using the Hotel Option menu, follow these
steps:
1. Turn the TV off.
2. Insert the USB device into the USB port on the rearof the TV.
3. Turn the TV on.
4. Go to the Hotel Option menu.
5. Press the up or down directional button to select Clone USB to TV,
and press the Select button on the remote control.
6. The message Clone settings from USB to TV is displayed. Press
the Select button on the remote control.
– If there is no file to copy on the USB device or the message that
there is no file appears, check the folder on yourUSB device.
– The folder name should be T-NKLCAKUC.
– Tables that list the settings that are cloned in the Hotel Option
menu begin on the next page.
"To enter the function, turn off the TV and insert a USB device, and
then turn on the TV and press the Select button for 5 seconds.
Pre-condition forcloning (check point)
Cloning should be done between the devices with the same
model and same software version.
Before cloning, all displays should be updated at the latest
version (same software version).

English - 18
Settings Cloned in the Hotel Option
Menu
The menu items may not be supported depending on the models.
Menu Item Sub Item Cloned or
not
Hospitality Mode Standalone / Interactive
(Default : Standalone) Yes
SI Vendor
Interactive: Samsung /
OCC / MTI / Nstreams /
Enseo / Cardinal / Guestek /
Seachange / MDC / Innvue
Standalone: Off / SSCP
Yes
SI Config
MDC ID Settings Yes
Power On
Power On Channel User Defined / Last Saved Yes
PowerOn Channel Num *** Yes
PowerOn Channel Type ATV / DTV / CATV / CDTV / IPTV Yes
Power On Volume UserDefined / Last Saved Yes
Power On Volume Num 0~100 Yes
Min Volume 0~100 Yes
Max Volume 0~100 Yes
Power On Source 
/ Last Saved Yes
Power On Option Power On / Standby / Last
Option Yes
Channel
Channel Setup Yes
Channel Editor Yes
Mixed Channel Map On / Off Yes
Dynamic SI On / Off Yes
MyChannel On / Off Yes
Menu OSD
Picture Menu Lock On / Off Yes
Menu Display On / Off Yes
Channel Menu Display On / Off Yes
Panel Button Lock Unlock / Lock / OnlyPower Yes
Clock
Local Time
Standalone Mode: Manual /
Time Channel
Interactive Mode: Manual /
Auto / Time Channel
Yes
Time Channel Type DTV / CDTV Yes
Time Channel Num *** Yes
Menu Item Sub Item Cloned or
not
External Source
USB Pop-up Screen Automatic / Disable Yes
External Source Banner On / Off Yes
Anynet+Return Source
PowerOn Src / Last Source
/ Each model source list (AV,
COMP, PC, HDMI1…)
Yes
Headphone Management
HP Mode On / Off Yes
Default HP Volume 0~100 Yes
Main Speaker On / Off Yes
Power and Energy Saving
Brightness Reduction On / Off Yes
Cloning
Clone TV to USB No
Clone USB to TV No
Setting Auto initialize On / Off Yes
Smart Service
Network Setup No
Download by App ID Yes
Apps Editable On / Off Yes
Ambient Editable On / Off Yes
Terms & Policy Yes
Smart Features Yes
Quick Settings Editor Yes
Service Discovery On / Off Yes
IGMP version  Yes
Samsung Account Yes
Security
FactoryLock On / Off Yes
Password Popup On / Off Yes
Password Input No
Password Setting Yes
Password Reset No
Security Mode On / Off Yes
USB Enable / Disable Yes
HDMI Enable / Disable Yes
DRM
DRM Mode Off / LYNK DRM / Pro:idiom /
LYNK DRM, PI Yes

English - 19
Setting Auto Initialize
OHotel Option menu > Cloning > Setting Auto Initialize
When you clone settings from one TV to another, you clone both
the guest side menu and hotel side menu settings: Picture, Sound,
Broadcasting, and Hotel Option menu. This lets you set nearly all
of the menu values on your hospitality TVs to the same, standard
settings. If you allow guests access to the guest side menus, for
example the Picture menu, they can change the settings in those
menus so they are no longerstandard. If you set the Setting Auto
Initialize function to on, the TV automatically restores (initializes) any
guest side menu values to the cloned, standard values when the TV is
turned off and then turned on again. Note that Setting Auto Initialize
works on cloned guest side menu values only. Settings which have
not been cloned are ignored.
The table below lists the settings that are restored to their cloned
values when you set the Setting Auto Initialize function to on.
The menu items may not be supported depending on the models.
Menu Item
Picture
Picture Mode Dynamic
Standard
Eco
Movie
FILMMAKER MODE
Picture Size Settings Picture Size
Fit to screen
Zoom and Position
Expert Settings Brightness
Contrast
Sharpness
Color
Tint (G/R)
Apply Picture Settings
Picture Clarity
Settings
Picture Clarity
Judder Reduction
LED Clear Motion
Noise Reduction
Contrast Enhancer
HDR Tone Mapping
Film Mode
Color Tone
Menu Item Sub Item Cloned or
not
System
Self
Diagnosis
for HTV
STB SI Vendor
Setting "Si Name" Ok / Failure No
Self Diagnosis for TV No
System Manager No
OTN Update On / Off Yes
SW Update No
Remote Management No
About This TV No
Standby LED On / Off Yes
TV Reset No
LYNK Cloud
Enrollment No
Enrollment Status Yes / No No
Virtual Standby
Virtual Standby Mode On / Off No
Reboot Time  Yes
Room Number No

English - 20
Menu Item
Connection
Device Name
Network Network Status
Open Network Settings
Reset Network
Expert Settings Power On with Mobile
IP Remote
Wi-Fi
External Device
Manager
Anynet+ (HDMI-CEC)
Input Signal Plus
HDMI Black Level
Input Device Manager Bluetooth Device List
Keyboard Settings
Keyboard Language
Keyboard Type
Mouse Settings
Primary Button
Pointer Speed
Device Connect
Manager
Access Notification
Device List
Game Mode Settings Game Mode
Game HDR
Broadcasting
Auto Program
Antenna
Audio Options Preferred Language
Multi-Track Sound
Menu Item
Expert Settings White Balance 2 Point
R-Gain
G-Gain
B-Gain
R-Offset
G-Offset
B-Offset
Reset
20 Point Settings
20 Point
Interval
Red
Green
Blue
Reset
Gamma
BT.1886
Shadow Detail
Color Space Settings Color Space
Color Gamut
Color
Red
Green
Blue
Reset
Reset Picture
Sound
Sound Output TV Speaker
Receiver (Optical)
Bluetooth Speaker List
Sound Mode Standard
Adaptive Sound
Amplify
Wi-Fi Speaker Surround Setup
Expert Settings Balance
Equalizer
HDMI-eARC Mode
Digital Output Audio Format
Digital Output Audio Delay
Auto Volume
Sound Feedback
Simultaneous Optical Output
Reset Sound