4
25
6
13
Remove all packaging from the TV. Retain the packaging.
If you dispose of it please do so according to any local regulations.
(P.N.: 1066522)
Do not connect the TV to the mains supply until you have
completed all the connections.
Install the batteries correctly by following the polarity (+ and -)
indications in the battery compartment.
Congratulations on the purchase of your new
Sandstrøm TV.
Your new TV incorporates the latest technology to enhance your viewing experience.
We would suggest that you allow about 20 mins for initial setup.
Please follow this guide for a successful first time installation.
Well done, your new TV is now ready to use.
You will find that there are many exciting features available. To get to know all
these features, please take some time to read the instruction manual provided
with your TV.
Quick Start Guide
40” / 46” HD Ready 1080p
LED Backlit LCD TV
S40LDIB10 / S46LDIB10
TV
Instruction Manual
TV Base
SCART Adapter CableScrews x 4 Audio Cable
Digital TV Switchover
Addendum
Remote Control /
AAA Batteries x 2
1. Lay the TV down on a flat surface with the back side facing up. Please make
sure to place a soft cushioned material (such as a pillow or thick piece of
foam) beneath the screen.
2. Slide in the base stand until the scew holes are aligned. Secure the base stand
with the 4 screws.
Slide in
Screws x 4 (included)
Connect one end of the RF coaxial cable to the aerial socket on the wall and
the other end of the cable to the ANT socket on the right rear side of your TV.
1. Slide the back cover to open the
battery compartment of the
remote control.
1
1
2
1. Connect the mains cable to the mains socket after you have completed all the
connections.
2. Switch on the POWER ON/OFF switch at the bottom of the TV. At this
stage, the TV switches to standby mode. The red LED indicator will illuminate
on the front panel of the TV.
3. Touch the touch control panel of the TV once to activate it (indicators on the
touch control panel will illuminate), and then press the touch sensitive control
on the touch control panel of the TV or press the button on the remote
control directly to turn the TV on (the red LED indicator will flash for a few
seconds).
2
Connecting the Aerial
Unpacking
Installing the Base Stand
Operating Your Remote Control
Connecting to the Mains Socket
Turning the TV on for the First Time
Still
Radio
DMP PVR
Rotate
Lang.
Subtitle
PagedownPageup
StopPlay/Pause
Browse
Zoom
Exit
TV/DTV Source
123
456
789
0
Recall Info
CHVOL
FAV
Sound
Picture
Recall
EPG
Menu
OK
CHList
Text Size Reveal Cancel
Hold
Sleep
Index
Sub.Code
Mix
2. Insert two AAA size batteries.
Close the battery compartment
cover.
Installation Guide
Mode Set ti ng Home Mode
Langua ge E ng li sh
Countr y UK
Auto Ins ta ll
Select Adjust Retu rn
Please ensure aerial is plugged in!!
1. Press the OK button or the button on the remote control to select Auto
Install.
2. A pop-up screen will be displayed. Press the OK button to start the auto
tuning. Auto tuning will commence. This operation may take about 15 minutes.
After auto tuning is complete, the first DTV channel tuned will be displayed on
screen.
The first time you turn the TV on, it will go straight into the Installation Guide.
Add channel only
Country selection UK
Start
It is always recommended to select "No"
to retune and overwrite the existing
channel list for the first time.
OR
COMMON INTERFACE
ANT 75 Ω
5V 50mA/Output
RF coaxial cable
(not included)
Installation Guide
Mode Setting Home Mode
Language English
Country UK
Auto Install
OK Enter Select Return
I/O
To mains socket
LED indicator
I/O
