Sanipex BAGNODESIGN BDM-BIS-T513X Series User manual

BDM-BIS-T513X-XX
BRISTOL SHOWER COLUMN SET WITH THERMOSTATIC MIXER
WITHOUT SHOWER HEAD(CROSS HANDLE)
www.sanipexgroup.com

IMPORTANT PLEASE READ
 B 
 

 






 L  C 



 x 
           
          
 



    








 

 







GENERAL CHARACTERISTICS
The Valve is suitable for all water heating systems provided it is installed correctly
by a competent and qualified installer.
Please refer to installation diagrams.
OPERATING SPECIFICATIONS
Hot water supply temperature:
Maximum: 85°C
Minimum: 5°C Higher than maximum required mixed temperature.
Advisable 65°C
Minimum difference between hot and mixed temperature is 10°C
Operating Pressure
Maximum: 5 Bar
Minimum: 0.1 Bar
Hot and Cold Operating pressure should be kept as balanced as possible in order
to maintain maximum efficiency.
When the supply pressure is higher than a 5 Bar a pressure reducing valve should
be fitted before the shower valve.
TECHNICAL DATA
The temperature control knob is with stop at 43°C to avoid scalding.
The mixer ports are supplied ¾” BSP threads.
PLUMBING RECOMMENDATIONS
•An independent hot and cold water supply is required for the shower system
please refer to installation diagrams.
•Large runs of pipe work will cause frictional loss of pressure.
•The recommended pipe work from both cylinder and water tank should be
22mm minimum for low-pressure systems.
•If more than one shower valve is installed the minimum feed from tank and
cylinder should be 28mm. (Ensure adequate supply of both hot and cold
water can be maintained).
WATER BYE LAWS
The mixing valve should be installed in accordance with the water bye laws. For
further details refer to the latest copy of Water Bye Laws guide or your local
water authority.

CLEANING OR REPLACE CARTRIDGE
•Shut off water supply to both inlets.
•Unscrew the grub screws(2) with Alan key 2,5 and remove the cross
handle(1).
•Unscrew the screws(3), take off temperature control(4) and plastic stop
ring(5).
•Remove the cartridge(6) with a spanner 30 mm.
•Clean filters(7) under running water or in vinegar for one night.
•Grease the “O”-rings and reassemble the cartridge(6) in to the body(8),
replace the plastic stop ring (5), according to the drawing and turn spindle
(A) until you reach required temperature 38°C.
•Re-fit temperature
control knob(4) and
fix it with the
screw(3).
•Re-fit the cross
handle(1) and fix it
with the grub
•screw(2).
MAINTENANCE – DIVERTER CARTRIDGE CHANGE
•Shut off water supply to both inlets.
•Unscrew the grub screws(2) with Alan key 2,5 and remove the cross
handle(1).
•Unscrew the screw(3) and remove the diverter handle(4).
•Unscrew flange(5) using 30mm spanner, remove the diverter cartridge(6).
•Place the new cartridge, inserting the pivot into the corresponding seat.
•Before re-assembling cartridge clean its housing with wet cloth and grease
“O” rings on cartridge.
•Reassemble the flange(5) using 30mm spanner.
•Re-fit the diverter handle (5) and secure with screw(4).
•Re-fit the cross
handle(1) and
secure with grub
screws(2).

IMPORTANT – CARE OF YOUR PRODUCT CLEANING
After use all finishes should be maintained by wiping with a soft, damp, clean cloth
and then polished using a dry duster. NO abrasive powder, detergents or polishes
should be used. Cleaner containing alcohol, acid or corrosive chemicals should not
be used.
NOTE
•Some household bleaches and denture cleaners can damage plated or
coloured finishes and if splashed onto a fitting should be immediately
washed off with cold water.
•If these instructions are followed we believe this fitting will give many years
of satisfactory use.
•We have a policy of continuous improvement and reserve the right to
change specification without notice.
•In case of prolonged disuse of the mixer in winter time, it is recommended
to close the system and empty the mixer to avoid damages caused by frost.

Note:

INM-BIS-T303VX-XX-02-22
www.sanipexgroup.com