Santec Barosa 2480MC User manual

Installation Instruction
Single Control Lavatory Set
BAROSA COLLECTION
Please read the instructions completely before beginning the installation.
Barosa Collection
Model Number: 2480MC
Flush both supply lines before installation, then shut off both supply lines.
Minimum hole size for the spout and handle trim is 1-1/4” and maximum of 1-1/2”
Remove fastening nut, metal washer and rubber washer from spout
assembly. Insert the lift rod into the fixture.
1
Rev 06/2016
The measurements shown are for reference only. Products and specifications shown are subject to change without notice.
www.santecfaucet.com | P: 310.542.0063 F: 310.542.5681
SPOUT INSTALLATION
1/7

The measurements shown are for reference only. Products and specifications shown are subject to change without notice.
www.santecfaucet.com | P: 310.542.0063 F: 310.542.5681
Apply a ring of silicone caulking around hole designated for spout.
DO NOT USE PLUMBERS’ PUTTY WHICH CAN DAMAGE FINISH.
Insert faucet assembly through hole in sink or counter top, being sure to
center faucet in hole.
2
Reinstall rubber gaket and metal washer from below. Hand tighten
fastening nut from below while aligning fixture.
3
Secure fixture from below by using either an adjustable wrench, basin
wrench, or deep socket to the lock nut. Wipe away excess silicone with
a wet finger or damp cloth. Connect flexible hoses to their respedic water
supplies.
4
NOTE: FLUSH THE LINES
Debris in the line will damage fixture and cause leaking. Failure to flush fixture could result in voiding the warranty.
After all the connections have been made to the inlet supplies, remove the aerator. Open both hot and cold valve.
Slowly open the handle lever and flush the lines for approximately 45 seconds. Turn off the water and reinsert aerator.
2/7
SILICONE

POP-UP INSTALLATION
1Remove the decorative drain flange, drain plug and gasket from
pop-up assembly. Do not remove the washer and lock nut.
2
Place the flange gasket onto the drain tube beveled side upward
and on top of the washer. Apply a ring of silicon caulking around
the top of sink drain opening. Do not use plumbers' putty.
3
Insert the threaded end of the assembly up from the under the sink
so that the top of the drain tube is through the drain opening.
Make sure the bottom of the drain tube is in the p-trap.
4Completely thread the drain flange onto the top of the drain tube.
Hand tighten the locknut from under the sink.
5
Position the drain tube so the side hole in the pop-up faces you.
Place the drain plug into the drain tube so its bottom hole is in line
with the side hole of the drain tube. Place the short end of the ball rod
into the side hole of the drain tube and through the hole in the drain
plug and tighten the ball rod nut so the ball rod moves freely.
NOTE: Do not over tighten.
6
Rotate the pop-up so the ball rod faces the back wall and tighten
the lock nut giving it an extra 1/4 turn. Hand tighten the nut at the
connection with P-trap. Test the rod and pop-up plug by pushing the
ball rod up and down to see if it raises and lowers the pop-up.
If not reinstall the ball rod.
7
Slip your faucet's pop-up lift rod through
the holes at the top of the lift rod strap and
hand tighten the thumb screw. Push the ball
rod down so the drain plug is in the up position.
Slip the one leg of the ball rod clip onto the ball
rod and then slide the lift rod strap onto the ball
rod using the nearest hole. Then slide the
second leg of the clip onto the rod.Test the
pop-up for smooth operation and adjust the
strap if necessary.
The measurements shown are for reference only. Products and specifications shown are subject to change without notice.
www.santecfaucet.com | P: 310.542.0063 F: 310.542.5681
3/7
Drain Plug
Lift Rod Strap
Drain Flange
Gasket
Washer
Lock Nut
1/4” Tail Piece
Lift Rod and Knob
Thumb Screw
Ball Rod
Ball Rod Clip
Ball Rod Nut
Side Hole

The measurements shown are for reference only. Products and specifications shown are subject to change without notice.
www.santecfaucet.com | P: 310.542.0063 F: 310.542.5681
PARTS DRAWING
4/7
* Please specify the finish when ordering the part.
# PART DESCRIPTION PART #
1 Flexible Hose - Cold K1321
2 Flexible Hose - Hot K1322
3 Lift Rod P0234
4 Rubber Pad P0803
5 Pad P0804
6 Lock Nut PM-383
P03567 25mm Control Cartridge
8 Complete Single Control Spout PS-600-U

SPECIFICATION SHEETS
The measurements shown are for reference only. Products and specifications shown are subject to change without notice.
www.santecfaucet.com | P: 310.542.0063 F: 310.542.5681
5/7
POP-UP
Ø 2
14
"
1
116
"3
516
"
12"
Ø 1
14
"
6
5
8
"
3
1
2
"
6
1
8
"
1
7
8
"
4
1
4
5
"
"

We recommend that all faucets, drains, etc., be gently wiped dry with a soft cloth after use to avoid water
spotting and water deposit build-up. A mild liquid hand soap may be used occasionally if desired. Use of a
non-abrasive carnauba wax will add protection to the finish and should be used if the faucets will not be dried
after use. For clear coated finishes, it is recommended to clean your product weekly with a soft moist cloth.
WARNING: Do not clean your SANTEC product with ammonia (Window cleaner), bleach, soap, acids,
abrasives, harsh polish, harsh cleaners, a coarse surfaced cloth, coarse sponge, or any type of scouring pad.
Doing so may ruin your faucet finish and/or void the warranty.
Thank you for making SANTEC a part of your lifestyle and luxury spa experience. Our products have been
created as works of enduring quality and sophisticated design.
Luxurious finishes need proper care and attention, so in order to understand how to properly clean your
distinctive luxury finish, please refer to the finish care information below:
Your SANTEC product can be identified in one of two categories: clear coated finishes or non-clear coated
finishes. Clear coated finishes are more scratch-sensitive and are more reactant to harsh cleaning chemicals
than non-clear coated finishes. Once you have identified the specific luxury finish of your SANTEC product,
please follow the important corresponding care instructions.
We recommend that all faucets, drains, etc., be gently wiped dry with a soft cloth after use to avoid water
spotting and water deposit build-up. A mild liquid hand soap may be used occasionally if desired. Use of a
non-abrasive carnauba wax is occasionally required and will add protection to the finish if the faucets will not
be dried after use.
FINISH CARE INFORMATION
CLEAR COATED FINISHES
NON-CLEAR COATED FINISHES
TO OBTAIN WARRANTY SERVICE
Please read ‘WHAT IS COVERED BY OUR WARRANTY’ and ‘EXCLUSIONS AND LIMITATIONS OF
WARRANTY’ sections to understand what is and what is not covered. Please have ready the proof of
purchase (original sales receipt), description of the problem, and carefully package the product or defective
part with postage prepaid. Then, please contact your local SANTEC Showroom or write to SANTEC Technical
Services.
The measurements shown are for reference only. Products and specifications shown are subject to change without notice.
www.santecfaucet.com | P: 310.542.0063 F: 310.542.5681
6/7

LIFETIME LIMITED WARRANTY
SANTEC is committed to enhancing your bathroom experience by creating luxury products that will provide
enduring satisfaction. Every effort has been made to satisfy the highest standards of design and production,
to create lasting peace of mind for our customers. We provide the following limited warranties on our products:
LENGH OF WARRANTY & WHO IS COVERED BY OUR WARRANTY
This warranty extends to the original consumer purchaser only and extends for as long as the original
purchaser owns the product and the home in which the product is installed.
WHAT IS COVERED BY OUR WARRANTY
FINISHES: SANTEC Polished Chrome, Polished Nickel and Satin Nickel finishes carry a Lifetime Limited
warranty against manufacturing defects and tarnish to the original purchaser. All other finishes carry a ten
(10) year limited warranty against manufacturing defects and tarnish to the original puchaser only.
CARTRIDGES: Santec cartridges carry a lifetime limited warranty, with the exception of thermostatic and
pressure balanced cartridges, which carry a three (3) year limited warranty against manufacturing defects
to the original purchaser.
PARTS: Santec parts carry a 10-year limited warranty against manufacturing defects, to the original
purchaser.
EXCLUSIONS & LIMITATIONS OF WARRANTY
Damage due to negligence, accident, abuse, improper installation, or improper maintenance such as, but
not limited to: heat from soldering during installation, the use of plumber’s putty, damage from tools used
during installation, the use or exposure to chemicals or cleaning products either abrasive or non-abrasive,
or the use of any cleaning tool or product other than a soft, clean cloth. Reverse osmosis may also shorten
the life of the finish.
Changes in the finish or in the product due to normal wear or aging does not cover any products or parts
which have been altered or used in a manner not typical for the product.
Loss, damages, or expense, incidental or consequential whatsoever, originating from the purchase,
installation, use, repair, failure, or replacement of any SANTEC product or part, allowed by law.
This warranty does not cover:
Commercial and/or Industrial installations and use of the product.
This warranty does not include labor, travel charges, or any costs incurred for repair, removal, installation,
servicing, diagnosing, or handling of either defective or replacement parts.
SANTEC reserves the product components of the covered product will be repaired, refinished, or replaced
at the sole discretion of SANTEC. SANTEC reserves the right to examine any product claimed defective prior
to any warranty claim being accepted or processed, at its sole discretion. This warranty gives you specific
legal rights and you may have other rights which may vary from state to state.
The measurements shown are for reference only. Products and specifications shown are subject to change without notice.
www.santecfaucet.com | P: 310.542.0063 F: 310.542.5681
Damage or deterioration caused by environmental impacts.
7/7