Santec MONZA Series User manual

KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE
PAGE 01
MINIMUM HOLE SIZE FOR THE SPOUT AND
HANDLE TRIM IS 1 ¼” AND MAXIMUM OF 1 ½”
*** NOTE: SHUT OFF WATER SUPPLY BEFORE BEGINNING INSTALLATION***
Black plastic lock nut
Trim Cylinder
Handle
Screw
Handle Cap
Black Soft Seating China Seals
Black Soft Seating China Seals
White Nylon Slip Washer
VACUUM BREAKER INSTALLATION
- Remove complete trim from vacuum breaker valve.
Install bidet elbow into threaded outlet.
Insert gasket into bidet wye and thread onto bottom of vacuum breaker valve.
Remove black plastic lock nut, nylon slip washer and one black self-seating
china seal.
Insert diverter valve body up from below and reinstall black self-seating china seal,
nylon slip washer and black plastic lock nut being sure to tighten firmly by hand.
- Thread trim cylinder onto vacuum breaker valve and tighten firmly. Place handle on
top and secure with brass screw. Insert handle cap with arrow facing towards front
of bidet.
PLEASE READ THE INSTRUCTIONS COMPLETELY
BEFORE BEGINNING THE INSTALLATION.
DO NOT TIGHTEN
HOSE
DO NOT TIGHTEN
HOSE
BIDET
COLLECTION
This is a general installation instruction
for the following collections:
* MONZA
* NOVO

INSTALLATION INSTRUCTIONS
PAGE 02
HANDLE TRIM INSTALLATION
HANDLE TRIM IS READY FOR DROP IN INSTALLATION.
DO NOT DISSASEMBLE.
- Remove the valve body mounting hardware from valve body.
Hot valve assembly “Red” to be mounted on left.
Cold valve assembly “Blue” to be mounted on right.
- Apply a ring of silicone caulking around the handle hole on bidet top.
DO NOT USE PLUMBERS' PUTTY, WHICH CAN DAMAGE FINISH.
- Slip valve through appropriate hole on top of bidet. Reinstall valve body mounting
hardware, fiber washer and valve body locknut. Align handles with respect to the bidet,
and tighten valve body locknut until secure.
- Aim outlet hoses towards bidet wye and attach securely to avoid leakage.
SANTECSANTEC
Fiber gasket
Brass lock nut
INLET HOSEINLET HOSE
SPRITZER INSTALLATION
- Apply a ring of silicone caulking around hole designated for spritzer application.
DO NOT USE PLUMBERS' PUTTY, WHICH CAN DAMAGE FINISH.
- Drop spritzer through the appropriate hole in bidet, attach mounting hardware and
tighten to avoid leakage.
- Attach 24” hose from spritzer to bidet elbow and tighten to avoid leakage.
Aerator Connecting hose
Aerator Shank Lock Nut
Metal Washer
Black Rubber Washer
Aerator base
Aerator Washer
Aerator Basket
Aerator Housing

INSTALLATION INSTRUCTIONS
PAGE 03
POP-UP INSTALLATION
- Remove decorative drain flange and drain plug from pop-up assembly.
- Apply a ring of silicone caulking to underside of decorative drain flange.
DO NOT USE PLUMBERS' PUTTY, WHICH CAN DAMAGE FINISH.
- Insert threaded end of the assembly up from below bidet.
Completely thread drain body into decorative drain flange and align with ball rod hole
facing back and tighten lock nut from below.
- Insert drain plug into decorative drain flange with adjustable eye-screw facing back.
Attach ball rod washers and ball rod nut to horizontal ball rod and install into drain
body. Do not over tighten, ball rod must operate freely.
- Drop lift knob flange through appropriate hole in bidet and attach mounting hardware.
Insert lift rod and knob through lift knob flange, lift rod strap and tighten thumbscrew.
- Gently push the horizontal ball rod down to place the drain plug in the up position.
- Slip one leg of ball rod clip off horizontal ball rod and insert lift rod strap, reattach leg
of ball rod clip.
- Test pop-up for smooth operation and adjust if necessary.
INLET HOSEINLET HOSE
SANTECSANTEC
INLET HOSEINLET HOSE
SANTECSANTEC
Drain Flange
Lift Rod Strap
Ball Rod
Drain Tube
Ball Rod Nut
Ball Rod Clip
Thumb Screw
Lock Nut
Washer
Gasket
Side hole
Rubber Washer
Metal Washer
Lock Nut
Lift Knob Flange
Flange Shank
Lift Rod
Lift Knob
FLUSH THE LINE
- After all connections have been made from inlet supplies to angle stops, remove the
spritzer housing, basket and washer.
- Open both hot and cold valves. Slowly open angle stops from below and flush the lines
for approximately 45 seconds to clear any debris.
- Turn water off and reinstall spritzer housing, basket and washer.

PAGE 04
SANTEC LIFETIME LIMITED WARRANTY
1. Finishes: Santec Polished Chrome and Polished Orobrass finishes carry a Lifetime Limited
warranty against manufacturing defects and tarnish to the original purchaser with the exclusion of
kitchen drain assemblies which, due to the nature of their use, are not warranted. Santec
recommended custom finishes carry a ten (10) years limited warranty against manufacturing
defects and tarnish to the original purchaser with the exclusion of kitchen and pop -up drain
assemblies which, due to the nature of their use, are not warranted.
2. Cartridges: Santec Cartridges carry a lifetime limited warranty against manufacturing defects for the
life of the product to the original purchaser.
3. Parts: Santec parts carry a Ten (10) year limited warranty against manufacturing defects, to the
original purchaser.
4. Warranty exclusions and limitations : This warranty does not cover: damage due to negligence,
accident, abuse, improper installation, or improper maintenance such as, but not limited to: heat from
soldering during installation, the use of plumbers putty, damage from tools used during installation,
the use or exposure to chemicals or cleaning products either abrasive or non abrasive or the use of
any cleaning tool or product other than a soft, clean cloth. This warranty does not cover: changes in
the finish or in the product due to normal wear or aging and does not cover any product or parts
which have been altered or used in a manner not typical for the product. This warranty does not
cover and Santec will not be held liable for damage to products caused by the freight carrier
and a claim should be made immediately to the freight carrier should this occur. This warranty
does not cover any cost involved in the installation, repair, or replace ment of any Santec product or
part. This warranty does not cover and Santec will not be held liable for any loss, damages, or
expenses, incidental or consequential whatsoever, originating from the purchase, installation, use,
repair, failure, or replaceme nt of any Santec product or part, as allowed by law. The product or
components of the covered product will either be repaired, refinished or replaced, at the sole
discretion of Santec. Santec reserves the right to examine any product claimed defective pr ior to
any warranty claim being accepted or processed, at its sole discretion. This warranty gives you
specific legal rights and you may have other rights which may vary from state to state.
Effective 01/01/03 - Replaces and supersedes any previously issued warranty.
FINISH CARE INFORMATION
For clear coated or enamel color finishes:
We recommend that all faucets, drains, etc. be
gently wiped dry with a soft cloth after use to avoid
water spotting and water deposit buildup. A mild
liquid hand soap, s uch as Ivory may be used
occasionally if desired. Use of a non -abrasive
carnauba wax will add protection to the finish and
should be used if the faucets will not be dried after
use. Santec Orobrass kitchen products are clear
coated.
For non-clear coated and specialty finishes:
We recommend that all faucets, drains, etc. be
gently wiped dry with a soft cloth after use to avoid
water spotting and water deposit buildup. Use of a
non-abrasive carnauba wax is required
occasionally.