Santiva Outdoors GOFR Livewell Adapter User manual

WARNING: This product contains chemicals known to the State of California to cause cancer and birth
defects or other reproductive harm. For more information go to https://www.p65warnings.ca.gov.
GOFR Livewell Adapter
Owner’s Manual

www.gofroutdoors.com
The GOFR Livewell Adapter allows you to convert most hard coolers, round or rectangular
buckets into a livewell.
Please follow the instructions below and please read all warnings and tips
to ensure the best results.
02
PARTS LIST :
P1 Bellhousing
P2 Core Assembly
P3 Flat Gasket
P4 Contoured Gasket
P5 Bucket Adaptor
P6 Screw Lock for Bucket Adaptor
P7 Drain Tube
P8 Caps for Air, Water in, Water out
P9 Hose Clamps
P10 Drain Cap
P11 Bucket Template
P12 Hole Saw
P13 Drain Elbow
P14 Elbow Connector
P15 Suction Cup
P16 Sand Paper
GOFR Livewell Adapter Owner’s Manual

www.gofroutdoors.com
STEP 1:
03
HARD COOLER CONVERSION
STEP 2:
P2
P1
• Screw Core (P2) into a hard cooler drain port. Secure firmly by hand tightening.
• From the inside of the cooler, place a
loosened Hose Clamp (P9) over the
Core (P2) as shown.
• Align the Bellhousing (P1) nipples with
the openings in the Core (P2) and push
as far as it will go.
• Move the Hose Clamp (P9) near the
base of the Bellhousing (P1), leaving
1mm of the Core still showing. Tighten
the clamp using a screw driver until
firm.
GOFR Livewell Adapter Owner’s Manual

www.gofroutdoors.com
STEP 5:
STEP 1:
BUCKETS (ROUND OR RECTANGULAR)
- REQUIRES DRILL -
04
STEP 4:
• If desired, connect our existing Air Tubing (P30) and Bellhousing (P1).
• Tape the template or find your desired location on the bucket to insert your Livewell
Connection System.
TIP: Drill the hole and position the system as low as possible (while still allowing room for
the connectors) on the container to allow for maximum water exchange.
• On the outside of the cooler, connect tubing as needed for air,
water, or full circulation.
• Assemble Drain Elbow (P13), and Drain Tube
(P7) using adapter. Install assembly on the
large drain nipple of the Bellhousing (P1)
with the Drain Tube (P7) pointed vertically.
TIP: Cut the Drain Tube (P7) to desired water
level, and install Drain Suction Cup (P15).
P1
GOFR Livewell Adapter Owner’s Manual

www.gofroutdoors.com
STEP 2:
STEP 4:
STEP 3:
STEP 5:
05
P3
or
P6P2
P5
P4
• Turn the bucket upside down and use the Hole Saw (P12) and electric
drill to cut a hole in bucket. Keep the drill perpendicular to the bucket
while drilling.
WARNINGS
- Make sure the surface area is clean and safe.
- Always use safety glasses when cutting or drilling.
- Make sure the bucket or container is secure and held firmly before
using the hole saw.
- Always use safety glasses and gloves when cutting or drilling.
• Install the Flat (P5) or Contoured Gasket (P4) onto the Bucket Adapter (P5)
depending on whether the bucket is rectangular or round respectively.
Install the assembly through the hole from the inside of the bucket.
STEP 6:
• Install Core Assembly
(P2) into the Bucket
Adaptor (P6) and screw
in until a firm
connection is made.
• After you have a hole cut, take a small piece of Sand Paper (P16) and gently
clean shavings and plastic pieces from inside the bucket and discard.
• Install Screw Lock for Bucket Adaptor (P6) onto Bucket Adapter (P5) from the
outside. For round buckets be sure to align the contoured gasket against the
side of the bucket to follow the natural shape and prevent gaps from forming.
GOFR Livewell Adapter Owner’s Manual

www.gofroutdoors.com
STEP 8:
• On the outside of the bucket, connect tubing as
needed for air, water, or full circulation.
• If desired, connect our existing Air Tubing (P30)
and Bellhousing (P1).
STEP 7:
06
• Assemble Elbow (P13), and Drain Tube (P7)
using adapter. Install assembly on the large
drain nipple of the Bellhousing (P1) with the
drain tube pointed vertically.
TIP: Cut the Drain Tube (P7) to desired water
level, and install Drain Suction Cup (P15).
P1
GOFR Livewell Adapter Owner’s Manual