Sanus Systems Sanus VisionMount VMAA18 User manual

Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 USA
US Customer Service: 1-800-359-5520 • [email protected] • www.sanus.com
©2008 Milestone AV Technologies
VMAA18
Do not use this product for any purpose not explicitly specied by Sanus Systems.
Improper installation or use may cause personal injury and/or property damage. If
you do not understand these instructions, or if you have doubts about the safety
of the installation, contact Sanus Customer Service. Sanus is not liable for injury or
damage caused by incorrect installation or use.
CAUTION
This product contains small items that could be a choking hazard if swallowed.
Keep these items away from young children!
WARNING
Thank you for choosing the Sanus VMAA18 wall mount. The Sanus VMAA18 wall mount is
designed to support a monitor sized up to 50 in. (127cm) and weighing up to 59 kg (130
lbs).The mount is adjustable; it will tilt +5° to -15°, swivel to ±90°, and roll ±6.°
This product is designed for use in wood stud walls only! The wall must be capable of
supporting up to ve times the weight of the monitor and mount combined. If you
have any doubts about the ability of the wall to support the monitor, contact Sanus
Customer Service, or a qualied contractor.
CAUTION
(6901-100016 <04>)

6901-100016 <04>
Supplied Parts and Hardware
Before starting assembly verify all parts are included and undamaged If any parts are missing or damaged do not return the item
to your dealer; contact Sanus Customer Service Never use damaged parts!
[01] x 1 [02] x 1
[04] x 2
[05] x 4
[10] x 1
3/16 in.
[03] x 2
[09] x 10
[15] x 4
5/16 x 2.5 in.
001426.eps
Lag Bolt for Wall Mounts
[30] x 4
1/4-20 x 2.0 in.
[07] x 4
1/4-20
[08] x 2
5/16-18 x 1 in.
[11] x 4
M4 x 12mm
001435.eps
[31] x 1
7/32 in.
[32] x 1
3/16 in.
[12] x 4
M5 x 12mm
[13] x 4
M6 x 12mm
[14] x 4
M8 x 16mm
[24] x 4
M4 x 30mm
[25] x 4
M5 x 30mm
[26] x 4
M6 x 35mm
[27] x 4
M8 x 40mm
[17] x 4
M4
[18] x 4
M5
[19] x 4
M6
[20] x 4
M8
[23] x 4
M6 / M8
[22] x 4
M4 / M5
[29] x 4
M6 / M8
[28] x 8
M4 / M5
[06] x 4
5/16 in.
[16] x 2
[21] x 4

6901-100016 <04>
1: Attach Brackets to Monitor
For Monitors with a Curved Back or Obstruction
For Monitors with a Flat Back
001427.eps
FPM70-Flat and Curved Back Brackets
001427.eps
FPM70-Flat and Curved Back Brackets
[17], [18],
[19], [20]
[03]
[11], [12],
[13], [14]
[28], [29]
4x
4x
001429.eps
FPM70-Brackets not level
001429.eps
FPM70-Brackets not level
001428.eps
FPM70-Curved Back Hardware
[17], [18],
[19], [20]
[03]
[11], [12],
[13], [14]
[28], [29]
[28]
[22], [23]
OPT
OPT
Use washer [28] with M4 or M5
hardware only.
OPT
OPT

6901-100016 <04>
2: Install Vise Assemblies
3: Install Arm Assembly to Monitor
001430.eps
FPM70-Vise assemblies installed
4x
001431.eps
FPM70-Detail, vise installation
[30]
[03]
[05]
[07]
Do not overtighten the nut [07]. The vise assembly [05] must
rotate freely around the carriage bolt [30].
NOTE
2x
[31]
2x
001438.eps
FPM70-Arm Attachment Detail
001438.eps
FPM70-Arm Attachment Detail
6x
Do not overtighten the fastener in
the vise assemblies [05]. Tighten
only enough to prevent the tubes
[04] from moving.
NOTE
001438.eps
FPM70-Arm Attachment Detail
001420.eps
Arrows
[03]
[04]
[05]
[04]
[03]
001438.eps
FPM70-Arm Attachment Detail
[04]
[02]

6901-100016 <04>
001439.eps
Attach Plate to Wall
4: Install Wall Plate
[06]
001439.eps
Attach Plate to Wall
001439.eps
Attach Plate to Wall
[01]
Do not overtighten the lag bolts [15]. Tighten only
until the washer [06] is pulled rmly against the wall
plate [01]. Periodic maintenance may be required.
NOTE
[15]
This product must only be used with wood studs
spaced 30 - 40 cm (12 - 16 in.) on center.
NOTE
3/16 in.

6901-100016 <04>
5: Attach Arm to Wall Plate
[32]
Avoid potential injuries or property
damage! Ensure the safety bolts [08]
are secure. Periodic maintenance
may be required.
CAUTION
[08]
HEAVY! You will need
assistance with this step.
[02] [01]

6901-100016 <04>
7: Install Cable Management
Be sure to leave enough slack in the
cables to allow the monitor to move
freely. Use the cable ties [09] and wire
clips [16] to secure the cables to the
brackets [03] and arm [02].
NOTE
001454.eps
FPM70-Cable Management
[09]
[16]
001454.eps
FPM70-Cable Management
[09]
[03]
6: Install Preventer
[21]
[10]
[32]
Install the preventer [10] on the left side if
you want the arm to fold to the left. Install
the preventer on the right side if you want
the arm to fold to the right.
OPT
OPT
[16]

6901-100016 <04>
Adjust Level
[31]
8: Adjust Monitor Position
001420.eps
Arrows
001420.eps
Arrows
001449.eps
FPM70-Back of Assembly
[A]
Adjust Left / Right Swivel
001451.eps
FPM70-Left / Right Angle
001420.eps
Arrows
001420.eps
Arrows
001451.eps
FPM70-Left / Right Angle
Avoid potential injuries or property damage! Remove the safety
bracket [B] only to adjust the swivel tension nut [C]. Be sure to replace
the safety bracket after adjusting the swivel tension nut. The hex hole
in the safety bracket must seat over the swivel tension nut.
CAUTION
001451.eps
FPM70-Left / Right Angle
[B]
[C]
001451.eps
FPM70-Left / Right Angle
[B]

6901-100016 <04>
Extend or Retract Arm
001447.eps
FMP70-Lower tab/locking fastener
[E]
001452.eps
FPM70-Extend / Retract Arm
Avoid potential injuries or property damage!
Do not remove the adjustment nut [E];
tighten or loosen only as necessary for easy
arm adjustment.
CAUTION
Adjust Up / Down Pitch
001450.eps
FMP70-Up / Down Pitch
001420.eps
Arrows
001453.eps
FPM70-Full Assembly
[D]
Adjust the pitch tension by tightening or
loosening the tension knobs [D].
NOTE
[31]
001420.eps
Arrows
[E]

6901-100016 <04>
Milestone AV Technologies, Inc.and its affiliated corporations and subsidiaries (collectively,“Milestone”),intend to make this manual accurate and complete.However, Milestone makes no
claim that the information contained herein covers all details, conditions, or variations.Nor does it provide for every possible contingency in connection with the installation or use of this
product.The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied,
regarding the information contained herein.Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.