Sanyo EM-C2000 User manual

S4q’tN‘
MIKROWELLENGERAET FUER DIE GASTRONOME
BEDIENUNGSANLEITUNG
COMMERCIAL USE MICROWAVE OVEN OPERATING
INSTRUCTIONS
FOUR PROFESSIONNEL AMICRO-ONDES
MODE D’EMPLOI
MAGNETRONOVEN VOOR COMMERCIEEL GEBRUIK
GEBRUIKSAANWIJZING
FORNO AMICROONDE PROFESSIONALE
ISTRUZIONI D’USO
EM-C2000

@
NAME AND FUNCTION OF PARTS
.10
I.Oven Cavity
Place food in this space to cook. Wipe the cavity clean each
time the oven is used.
2. Stirrer Shield
Clean with care.
3.Door Handle
When the door handle is gripped, abuilt-in switch turns off
the power before the door is opened.
4.Door
5.Door Latch
6. Glass Shielded Viewing Window
The progress of cooking can be observed while oven is op-
erating.
7.Door Arm
Prevents door swinging back.
8. Cabinet
9. Control Panel
10. Mains Lead
11 .Safety Interlock System
With built-in safety interlock.
12.Air Filter
Clean with care.
Note: When opening door, be sure to open fl)lly.
19

iii
CONTROL PANEL
,,r-—
1, Digital Timer
~].
F,a
10,,,,,,,,,,]*
1
4
9
6
2
1
Indicates when unit is operating
memory has been set.
Programme is displayed by NO.
Displays remaining cooking time.
Displays cooking power levels.
E,,
,,,
,” ,.=
a
.. .,
4-’ ,J
.-,. -.
4’,, ,, -J
/
2. Timer (Manual and Repeat)
3. Power Select Buttons (Manual cooking)
~M+~~--~
—i
4. Multiple Quantity Selection Key
——
1X211X31
~—
●For tailoring cooking to double or triple-quantity.
These keys to be used in conjunction with
Programme key.
5. Programme Selection Keys
and
6. Clear Key
●For canceling setting, interrupting the setting process when
amistake has been made, or stopping cooking before the
completion of the cooking process.
7. Memory Key
the
10
The unit is ready to begin operation as
soon as the heating time has been
programmed, using these ten keys
(numbered 1to O).
The time selected WIII be displayed, and
“count down” after the process is begun.
~
.For entering the desired power output and cooking time,
8. Power Key
m
I~I
●For entering the desired power output Into the unit’s
memory.
9. Timer Key
IAl’For determining power output anc~
cooking time during programming.
-5
~----- —8
—7
---—- 10
–— 3
Cm3
●For entering the desired cooking time into the unit’s
memory.
Start Key
101
●For timer cooking.
●For restart at programmed cooking
20

m
INSTALLATION
1.
2.
3.
The oven surrouno and also tre surrou[!.i of !PIe coiltrol 4
panel IS covered Dy aprotective L)lasIIL \illll, d;?d [:IIS 511uLilC
be rernove(~ prior tc i~uttil(; tt?e eve:] .!~to (!se.
Install the oven on aflat, level surface 5
Strong erlougl] tu %Tel~ rle,ir [II ,1.;II :: ~~ .II,I i o
avoid ttle possltllllry JT i;.l(isl!!~j .:,’ !: .:J.’-. [I(. OYCI?
MLISt be 117 :1 sTc1121(: i)us IDcI!’
Keep the oven away from heat aria water
WARNING -This appliance must be earthed
THIS PLUG !S NOT WATERPROOF =KEEP DRY
*WARNING: APLUG WITH
IS HAZARDOUS IF ENGAGED BARED FLEXIBLE CORDS
IN ALIVE SOCKET OUTLET.
21

m
HOW TO USE
YOUR SANYO MICROWAVE OVEN SAFELY
Although your oven is provided with safety features, it is
important to observe the following:
a) It is important not to defeat or tamper with safety interlocks.
b) Do not place any ob)ect between the oven front face and
the door or allow residue to accumulate on sea!r]g
surfaces. Wipe the sealing area frequently wtth an]iltl
detergent, rinse and wipe dry. Never use aoraslve pu~.!~rs
or pads.
c) When opened, the door mLISI r!o~ r)e suu; euea to ~[ra: T,.
example, achild hanging on an opened door o: any ,:.TI;I
could cause the oven to fall forward to cause lr~jury ar~cl :+isu
damage to the door.
Do not operate the oven it II is da:~iag~{! !Irw !; I:+> ::,1.
repaired by aqualrf!ed service +::g I::eer !! IS :)~~:1. /.:IrI\
important that the ove:~ CIoses ~r:~pe:iy ar~a tr:~: tnere IS rio
damage to the :
i) Door (bent)
ii) Hinges and Latches (broken or lo~seriec>’
iii) Door seals and Seallng surfaces
d) It is dangerous for anyone other than aproperly qualified
service engineer trained by SANYC tc carry OUI adjust
ments or repairs.
NOTE
It is quite normal for steam to be emitted around the door, or
for misting to occur on the door, or ever +~r waler f!roplets
to appear below the door during [t~e .kI!I. J v e
This is merely condensation trorv t!ne near UT ::, “.I ::11
does not affect the safety of your oven.
The door is not intended 10 sea’ ~he overi ;awt~ ..i>I; ::eIV
:but its special SANYO design contributes to the complete
~safety of the appliance.
———..—
Note: After cooking or wtler~ YCLI stup cooking k>v o[:e:IIr Ig
the door. The fan of the rover, VVIII tL]rn ror OVP mnote
OTHER SAFEGUARDS:
1. Never remove the cabinet
High voltage electricity IS useu [r) trlls ove II, so ue SLI!P Iu
to remove the cahlne:
HINTS FOR COOKING
1.
2.
3.
4.
2
3
4
5
6
7
8
9
10
11
12
13
14
22

ii
MICROWAVE OVEN COOKING KNOW-HOW
OPERATING INSTRUCTIONS (1)
4
?A A!
n, M
co
I.++--y: \j
~..... .———.—.——
23

iii
~TIMER (MANUAL) COOKING BY KEYS )
1) Connect mains lead to power outlet.
2) Open the door, The oven Iampwill light.
+Operational flow IDisplay window
-—.———.——————.—-——
Put food in suitable containers on the tray in the oven cavity ~
Iand close the door. The oven lamp will go out. .“O” will appear on the display
~:-z:?.::::.:’:: f?”!
display and Power Level 10 Bar.
●Input POWER level 8with the
31 PROGRAMME keys ‘n ●Power Level “8” Bar.
..Touch: number”8” —— .. ..—..~.. --–– --——
’16 ‘-
I
.Touch ~key “n “-
.NO change in display
~-- .–.———. .—.—
‘ml
●Input the desired time with the
51 PROGRAMME keys
●Touch number “l” of the desired 1a●“1” will appear on the display
minute 30 seconds
—..
6
ml
●Touch number”3” B
●“3” will ap~ear on the right of “l”,
“13” shows in the display window
—— L...
7
El
●Touch another “O” mW:::W
●“1,30” then shows in the display
t——..—.
8~m●TOuch’tartKey ~p]
●TO start cooking, the correspon-
ding indicator lights up and the
digital timer counts down to zero.
,——~ . . . . . . .
●Cooking time ends
m
●The “bee~” tone sounds, “O” will
9~ ●Remove the food fronl oven show.
The oven lamp will go o~jt.
I
Note: When you operate Max Power, don’t touch “~“key. Max power operation will autornaticallv be made so vou can skip
operation 2and 3. Max input timer is ten minutes.
Note: When apower select button is pressed to commence acooking cvcle, there w!I1 he an initial delav c; aonroximatelv 3seconds
oven stabilisation time before the cooking cycle actuallv starts.
Note: Correct operation of any of the Dower select buttons is indicated bv ashort hee~ tone. !f this tone IS not heard. onerate buttons
again, apply ing firm finger pressure to centre of button. Sho~~ld there still he notn~e, tt IS ar- Indication that the “~“bLltton
needs to be o~erated.
24

I
OPERATING INSTRUCTIONS (2)
IUSING THE PROGRAMME KEY FOR MEMORY STORAGE I
1. Programmed (l-Stage) Cooking
Power Level ...................max power
(Example) To programme the following on programme No.3: (~or30 ~econd~,
Operational flow Display window
*—. –
1m~ = pay
.The “O” will appear on the dis-
.Touch ~key (Isttime)
...—..—— .
2m●Touch ~key (2nd time) ‘n .No change
3hi ●Touch PROGRAMME key [=] .Light No.3
number “3” Power level bar”1 O“
4m“Touch” ~“key I[=] .No change
ml
●Input the operating time
5I=] pay
●The “3” will appear on the dis-
with PROGRAMME keys
.First, touch number “3” .L–—... --–––—---- ---—
6rd .Then, touch number “O” ‘c] ,,3,,
●The “0” will appear behind the
7&
1
Inplay
●The “O” will appear on the dis-
.Then, touch ~key
Note: When yOLI operate with Max. power, do not touch “~“key.Max power operation automatically be made,

b
OPERATING INSTRUCTIONS (3)
IUSING THE PROGRAMME KEY FOR MEMORY STORAGE \
2. Programmed (l-Stage) Cooking
(Example) To programme the following on programme N0,4:( ~’r~5r~~c~~~~
1
2
3
4
5
6
Operational flow
IM] .Touch ~key (Ist time).
IM] ●Touch ~key (2nd time).
IA!
●Touch PROGRAMME key
Anumber “4”.
Display window
The “O” will appear on the
dis~lay.
No change
O“ bar.
Light No,4
Power level ‘“
E@3 .Touch ~key. ~[-] ●
El ●Input ‘(power level 5“ with ~
PROGRAMME key
Touch number “5”. [~] “o
. ..... .—
m●Touch ~key pi.
.—-.
;I AI
●Input the operating time with the
7i PROGRAMME keys.
ATouch number’’4”. p]”
~~
n
●Then, touch number “5”. p,”
~. . .
‘m●Then, touch ~key. ‘n”
No change
Power Level “5” Bar.
No change.
The “4” will appear on the
display.
The “5” will appear behind the
“4”.
“45” then show in the display
window.
The “O” will appear on the
display.
POWER LEVEL LIST Note:
—4
POWER LEVEL
(Input figure) POWER (W) Max. input tlrme 1 2
L—–——-—————-–––––. -—-—- -– J
I
L’ .–- 1080 ~---:-------------
5900 30 mln 00 sec.
—.———. ——..—.. I
4720 ,,
I3540 ,,
I2360 I
L——.—.....—.-.————. . . 1
I1“I80
A“beep’’t ones oundswheneverany key is touched.
If the desired numeral is not displayed, touch
“CCI” and restart ‘procedures) from the
beginning.
If an operating time over the MAX. innut time is
selected, subsegment key o~eration is impossible.
To enter 1minute (60 seconds) inpljt “100”.
The storing Drocess is completed bv touching
If “~“ key is not touched, the information will
Inot be retained and previous memory information
be retained.
26

3. Programmed (2-Stage) Cooking
(Example) To programme the following on programme No. 3:
~ir~t ~Max power
for 30 seconds. Second (Power Level 2
for 10 minutes.
Operating flow 1-6 is the same as step 1-6 of l-stage cooking, then: (see page 25)
Operational flow Display window
7m‘Touch m‘ey =] ,ar,
.The colon will appear on th~
display and Power Level” 10’
bl
●Input POWER level 2with
8the PROGRAMME keys [~] ●Power Level “2” Bar
.Touch: number “2”
‘m““ouch m‘ey pi .No change in display
ml ●Input the desired time with
10 the PROGRAMME keys
.Touch number “l” Of the ~] ●“l” will appear on the display
desire 10 minutes
11 ml [VI “l~~~wshows in the display
.“O” will appear on the right of
●Touch number “O”
o
12
n] [~] playwindow
.“100” then shows in the dis-
.Touch another “O”
t
13 ml
●Touch another “O” ~-l ●“1000” then shows in the dis-
play window
14 &(ending input)
●Touch” ~“key
n.“O” will appear on the display
E