Sanyo Dp50749 - 50" plasma tv User manual

Sanyo Service Tip USIK / YX6E CHASSIS 07/27/12

IC5750A is located under the large shield. IC 5750A is a 48 pin NAND FLASH IC wit

easy access for replacement. This will fix +80% of the boards with the symptom below.

Sanyo Part Number: QXXAVD058- - -M

Chassis

Version IC 5700

Samsung IC 5700

Quimonda

P37819-00 SW84 SW82

P42849-00 SW84 SW82

P42849-01 SW84 SW82

P42849-02 SW84 SW82

P42849-04 SW84 SW82

P42849-05 SW84 SW82

P46849-00 SW84 SW82

P46849-01 SW84 SW82

P46849-02 SW84 SW82

P46849-03 SW84 SW82

P46819-00 SW84 SW82

P50749-00 SW84 SW82

P50749-01 SW84 SW82

P50749-02 SW84 SW82

P50749-03 SW84 SW82

P50719-00 SW84 SW82 IC5750 to be replaced

P52449-01 SW85 SW83 Check IC manufacture for either Samsung or Quimonda

P42840-02 SW84 SW82 The IC 5750A you receive will have software 84 installed in it

P42840-03 SW84 SW82 IC 5700's manufacture is Quimonda or TV is a 52" then the

P42840-04 SW84 SW82 software will need to be changed with the use of a USB drive.

P46840-01 SW84 SW82

P46840-02 SW84 SW82 Note : Only use this software in the Sanyo TVs listed.

If used in wrong chassis, it could cause TV not to come

P50740-01 SW84 SW82 on and IC 5750 will need to be changed again.

SYMPTOM: If the power LED on front of the TV is turning ON

for 10-20 seconds, OFF for 1-2 second and keeps repeating, the

problem is most likely IC5750A. Affected models are the 2009 &

2010 TVs (LCD and Plasma) listed.

SYMPTOM: If the power LED on front of the TV is turning ON for 10-20 seconds, OFF for

1-2 second and keeps repeating, the problem is most likely IC5750A. Affected models are

the 2009 & 2010 TVs (LCD and Plasma) listed.

You must use the 3

dashes when ordering

this IC.

DP50749-00

Panel: Self Test

Panel is capable of generating internal patterns without the Main

Signal Board attached. (rotating: white / red / green / blue / and

various other patterns)

This test eliminates Main Signal Board from circuit and confirms if

panel itself is operating properly.

1) Unplug these connectors on Main Signal Board.

K8P

K8B

2) Short pins 1-4 together on Logic Bd. at under connector

CN2000. (a small screw works good to short all together)

3) K8P Connector

These pins must be shorted together.

p#1 & #3

p#2 & #7

Shorting these pins together will automatically energize the panel,

after AC power has been applied in step #4 below.

4) AC power must be applied to panel. Power cord can still be

attached to AC Filter, or power can be applied directly to

CN800s on SMPS.

(recommend that AC Filter still be used for ease of connection,

but can be bypassed if needed)

5) Please remember to remove the screw on the Logic Board under

CN2000, when finished.

note: no audio is available with panel self test

Specifications

POWER RATING . . . . . . . . . . . . . . . . . . . . . . . . . 120VAC

464 W (AVG.)

ANTENNA INPUT IMPEDANCE. . . . . . . . . . . . . . . . . 75Ω

UHF/VHF/CATV

DIGITAL

RECEIVING CHANNEL . . . . . . . . . . . . . . . . . 2 - 13 (VHF),

14 - 69 (UHF),

01, 14-94, 95-135 (CATV)

1-135 (DIGITAL)

REMOTE READY. . . . . . . . . 54 KEY REMOTE CONTROL

SOUND OUTPUT. . . . . . . . . . . . . . . . . . . . . . . 10.0 W/CH

INTERMEDIATE FREQUENCY

PICTURE IF CARRIER . . . . . . . . . . . . . . . . . . 45.75MHz

SOUND IF CARRIER . . . . . . . . . . . . . . . . . . . 41.25MHz

COLOR SUB CARRIER . . . . . . . . . . . . . . . . . 42.17MHz

CABINET DIMENSIONS

WIDTH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1245mm

HEIGHT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 842mm

DEPTH INCLUDING BASE . . . . . . . . . . . . . . . . 360mm

REFERENCE No. SM780163

DP50749, J4FE, PRODUCT CODE 1-110-109-04

FILE NO.

SERVICE MANUAL Remote Control Digital

Color Television DP50749 (U.S.A.)

(CANADA)

ORIGINAL VERSION

Chassis No. P50749-00

NOTE: Match the Chassis No. on

the unit’s back cover with

the Chassis No. in the

Service Manual.

If the Original Version

Service Manual Chassis

No. does not match the

unit’s, additional Service

Literature is required. You

must refer to “Notices” to the

Original Service Manual

prior to servicing the unit.

Servicing should be performed by only trained and qualified service personnel.

Contents

SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . 2

SERVICE ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . 3

ON-SCREEN SERVICE MENU . . . . . . . . . . . . . . . . . . . . . 4

POWER FAILURE CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . 5

MECHANICAL DISASSEMBLY . . . . . . . . . . . . . . . . . . . . 6

CHASSIS ELECTRICAL PARTS LIST . . . . . . . . . . . . . . . . 8

COMPONENT AND TESTPOINT LOCATIONS . . . . . . 22

BLOCK DIAGRAM POWER LINES. . . . . . . . . . . . . . . . . 25

BLOCK DIAGRAM SIGNAL LINES . . . . . . . . . . . . . . . . 26

IC BLOCK DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . 27

TROUBLESHOOTING FLOW CHARTS . . . . . . . . . . . . . 33

CONTROL PORT FUNCTIONS. . . . . . . . . . . . . . . . . . . . 36

MAIN SHEET BLOCK DIAGRAM & PERIPHERICALS. . 38

SCHEMATIC NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

IC, DIODE, AND TRANSISTOR PIN LAYOUTS. . . . . . . 40

PC BOARD CONNECTIONS AND LOCATIONS . . . . . . 41

CAPACITOR AND RESISTOR CODE CHART . . . . . . . . 42

SCHEMATIC DIAGRAMS. . . . . . . . . . . . . . . . . . . . . . . . 43

– 2 –

SAFETY PRECAUTIONS

WARNING: The chassis of this receiver has a floating

ground with the potential of one half the AC line voltage in

respect to earth ground. Service should not be attempted by

anyone not familiar with the precautions necessary when

working on this type of equipment.

The following precautions must be observed:

1. An isolation transformer must be connected in the power

line between the receiver and the AC line before any ser-

vice is performed on the receiver.

2. Comply with all caution and safety-related notes provid-

ed inside the cabinet, on the chassis, and on the back.

3. When replacing a chassis in the cabinet, always be certain

that all the protective devices are installed properly, such

as control knobs, adjustment covers, shields and barriers.

4. Before replacing the back cover of the set, thoroughly

inspect the inside of the cabinet to see that no stray parts

or tools have been left inside.

Before returning any television to the customer, the

service technician must perform the following safety

checks to be sure that the unit is completely safe to

operate without danger of electrical shock.

ANTENNA COLD CHECK

Remove AC plug from the 120 VAC outlet and place a

jumper across the two blades. Connect one lead of an ohm-

meter to the jumpered AC plug, and touch the other lead to

each exposed antenna terminal (UHF and VHF antenna ter-

minals). The resistance must measure between 1M ohm and

5.2M ohm. Any resistance value below or above this range

indicates an abnormality which requires corrective action.

LEAKAGE CURRENT CHECK

Plug the AC line cord directly into a 120 VAC outlet. (Do not

use an isolation transformer for this check.) Use an AC volt-

meter, that has 5000 ohms per volt or more sensitivity.

Connect a 1500 ohm 10 watt resistor, paralleled by a 0.15 μF

150 VAC capacitor, between a known good earth ground

(water pipe, conduit, etc.) and all exposed metal parts of the

cabinet (antennas, handle bracket, metal cabinet, screw

heads, metal overlays, control shafts, etc.). Measure the AC

voltage across the 1500 ohm resistor. The AC voltage

should not exceed 750 mV. A reading exceeding 750 mV

indicates that a dangerous potential exists. The fault must

be located and corrected. Repeat the above test with the

receiver power plug reversed.

NEVER RETURN A RECEIVER TO THE CUSTOMER

WITHOUT TAKING THE NECESSARY CORRECTIVE ACTION.

PRODUCT SAFETY NOTICE

When replacing components in a receiver, always keep in

mind the necessary product safety precautions. Pay special

attention to the replacement of components marked with a

in the parts list and in the schematic diagrams. To ensure

safe product operation, it is necessary to replace those com-

ponents with the exact same PARTS.

SERVICING ELECTROSTATICALLY SENSITIVE DEVICES

Semiconductors (solid-state devices) that can be damaged

by static electricity are referred to as Electrostatically

Sensitive (ES) devices. Examples of typical ES devices are:

Integrated Circuits (IC), Field-Effect Transistors (FET), and

“chip” components. The following techniques should be

observed strictly, to reduce the occurrence of semiconduc-

tor damage due to electrostatic discharge.

1. Immediately prior to handling any semiconductor com-

ponent or an assembly containing a semiconductor

device or devices, discharge the electrostatic buildup on

your body by touching a known earth ground. You may

also obtain and wear a commercially available discharg-

ing wrist strap device.

CAUTION: Be sure to remove the wrist strap before

applying power to any unit being serviced.

2. After removing an ES equipped assembly, place it on a

conductive surface, such as, aluminum foil, to prevent

buildup or exposure to static electricity.

3. Use only grounded-tip soldering irons to solder or unsol-

der ES devices.

4. Use only anti-static solder removal devices. Some suc-

tion-type devices can generate static electricity adequate

to damage ES devices.

5. A replacement ES device will come packaged in protective

material (conductive foam, aluminum foil, or some compa-

rable conductive material). Do Not remove an ES device

from its protective packaging unless you are prepared to

install it immediately.

6. Precisely prior to removing an ES device from its protective

packaging, touch the protective packaging to the chassis or

assembly in which the device will be installed.

CAUTION: Be sure that no power is applied to the chassis or

circuit assembly.

7. Incidental body movements, such as, lifting a foot from a

carpeted floor or the rubbing of fabric together can gener-

ate static electricity sufficient to damage ES devices.

Therefore, minimize all body movements while handling

exposed (unpackaged) ES devices.

SAFETY INSTRUCTIONS

– 3 –

SERVICE ADJUSTMENTS

GENERAL

This set has an On-screen Service Menu system included in

the CPU that allows remote operation for most of the

service adjustments.

ON-SCREEN SERVICE MENU SYSTEM

1. Enter the Service Menu:

•Turn off the receiver and disconnect the AC power

supply.

•While pressing the Volume (–) button on the televi-

sion, reconnect the AC power supply. The Service

Menu will now appear. The remote can now be used

to make adjustments. See Figure 1 below.

2. Service Adjustments:

•Press the Cursor  and key to select the desired

service menu item you want to adjust. See page 4 for

the On-screen Service Menu.

•Use the Cursor or key to adjust the data.

The or key will increase or decrease the data

sequentially.

3. Exit from the Service Menu:

•Press the MENU key to turn off the Service Menu

display.

Figure 1. Service Menu Display

HEX DATA

ITEM NO. TITLE

POWER

VOL

Menu:

Exit Service Menu Cursor :

Select Item

Cursor :

Adjust the data

Volume – :Enter Service Menu

– 4 –

ON-SCREEN SERVICE MENU

Table 1. ON-SCREEN SERVICE MENU

When IC801 (EEPROM) is replaced, check the bus data to confirm they are the same as below. See page 3 for

On-Screen Service Menu access and adjustments.

PROGRAM CODES

The microprocessor used in this model is a multi-purpose type and is used in several different models. To ensure

proper operation and the correct features for your particular model, the program codes must be correct.

Note 1. Option Data 1 (NO. 087 OP1) should be hexadecimal

00. See 087 above. If this program code is wrong the TV will

not operate properly.

Note 2. Option Data 2 (NO. 088 OP2) should be hexadecimal

3D. See 088 above. If this program code is wrong the TV will

not operate properly.

No. Title Initial Data Note

1A0 MUTE A0h Audio mute at Power ON

086 VOL 30h Volume setup inspection

087 OP1 00h Option 1 Data (HDMI)

088 OP2 3Dh Option 2 Data (Display Panel)

101 1R00 00h ROM Correction Data

102 1R01 00h ROM Correction Data

↓↓ ↓ ↓

197 2R47 00h ROM Correction Data

198 2R48 00h ROM Correction Data

• All data except in gray box area is fixed. Do not change for correct operating.

• Data in gray box is initial and can be set according to adjusment information.

– 5 –

POWER FAILURE CIRCUIT

Check the following if the unit is turned off by the power

failure detector.

1. Disconnect the AC power cord (120V AC line) for a short

time.

2. Connect a DC Voltmeter to the circuits shown below.

3. Press the Power key and check for the proper voltage

supplies.

4. If any of these voltages is low, the power failure detec-

tor should turn the unit off within three seconds.

5. Check all circuits shown below.

Note: If power failure is detected 3 times in 15 minutes,

the set will enter the standby mode and cannot be

switched On.To reset the operating programs of the

CPU it is necessary to disconnect the AC cord for a

short time.

CPU (IC800) is programmed so the set will go to standby

mode when there is circuit failure as described below.

(Refer to“Block Diagram Power Lines”.)

This unit is equipped with a Power Failure Detector function

included in the CPU which checks for an abnormal condi-

tion in the chassis power supplies.

If, while the power is on, a failure is caused by any of the

following that results in a low voltage supply, the CPU will

turn the unit off in 1.5 seconds to prevent further damage:

•Failure within the power supply circuits.

•A short circuit in the load side from the supply.

Power Failure: Detected voltage failure for circuit.

(Connected to IC800 pin 48 and pin 23.)

(Normal: High; Failure: Low)

If, while the power is off, the power is switched on and any

of these failures remains uncorrected, the CPU will shut off

the power within three seconds.

IC800 (SUB-CPU)

1,2

5,6

4,2

Power Fail

Power On

Power Fail

(LVDS)

Power Board

Main

D1660

D1683

K8B

D1651

D1674

IC1680

Q1651

IC1670

15V

K8B

LVDS_POW

D1633

3,6

D1632 IC1630

3.3V

– 6 –

STAND REMOVAL

Note: Position TV face down on a padded or cushioned

surface to protect the screen and finish.

Remove 4 screws (B: 6x16) to take the stand off.

MECHANICAL DISASSEMBLY

CCC

CCCC

CAUTION:

This PDP TV uses several different kinds of screws. Using the correct screw is necessary to prevent damage. Lead wires must

be redressed to their previous locations after servicing. The Earth sheet and gasket are provided to prevent interference to

other radio and television receivers. The Earth sheet and gasket should be returned to its previous position after servicing.

BACK CABINET REMOVAL

Remove 33 screws to take the back cabinet off.

A:4x10, 13pcs; B:6x16, 4pcs; C4x8, 16 pcs

– 7 –

BOARD LOCATIONS

MAIN BOARD REMOVAL

Remove 10 screws (D3x12, 3 pcs; E:PC terminal nuts, 2 pcs;

F:3x6, 5 pcs) and 1 nut (Tuner) to take the main board off.

244

Nut (Tuner)

FFF

Main Board

MECHANICAL DISASSEMBLY (CONT.)

ELECTROSTATICALLY SENSITIVE DEVICES

Many solid-state devices (especially Integrated

Circuits) are Electrostatically Sensitive, and, therefore,

require special handling techniques as described

under “Servicing Electrostatically Sensitive Devices,”

on page two in this service literature.

– 8 –

1: KEW SW BOARD REMOVAL

Remove 1 screw (D: 3x12) to take the key sw board off.

2: RC LED REMOVAL

Remove 1 screw (H:3x6) to take the rc led board off.

3: SPEAKER REMOVAL

Remove 4 screws (A: 4x10) to take off each speaker.

HAA

Speaker

RC LED Board

KEY SW Board

AAAA

AAII

MECHANICAL DISASSEMBLY (CONT.)

FILTER GLASS REMOVAL

1. Take the connectors of below lead wire off.

control Board ~ Main Board: K8CTR

Speakers ~ Main Board: KSP

2. Remove 10 screws (A:4x10, 8 pcs; I:4x8, 2 pcs)

to take the panel module and panel holders

(Mounting Frames) with boards off.

Continued...

– 9 –

MECHANICAL DISASSEMBLY (CONT.)

PANEL MODULE REMOVAL

1. Disconnect the following socket connections.

PDP Module (Power Unit) ~ Main Board: P813

PDP Module (Power Unit) ~ AC inlet: SC101

2. Remove 6 screws (J:4x14) from the panel holders

(Mounting Frames) to take the panel module off.

3. Remove 8 screw (I4x8) to take off each mounting

panel (4 pcs).

3. Remove 18 screws (F3x6) to take the mounting

filter (6 pcs) and filter glass off.

FFF F F F

Mounting Filter

Filter Grass

Mounting Frame

Mounting Panel

(under the

Mounting Frame,

4pcs)

– 10 –

CHASSIS ELECTRICAL PARTS LIST

CAUTION: To Protect against electrical shock and for continued product safety, refer to SAFETY PRECAUTIONS

and PRODUCT SAFETY NOTICE on Page 2.

PRODUCT SAFETY NOTICE

PRODUCT SAFETY SHOULD BE CONSIDERED WHEN A REPLACEMENT IS MADE IN ANY AREA OF A RECEIVER.

COMPONENTS INDICATED BY A IN THIS PARTS LIST AND THE SCHEMATIC DIAGRAM DESIGNATE

COMPONENTS IN WHICH SAFETY CAN BE OF SPECIAL SIGNIFICANCE. IT IS PARTICULARLY RECOMMENDED

THAT ONLY PARTS DESIGNATED ON THE FOLLOWING PARTS LIST BE USED FOR COMPONENT REPLACE-

MENT DESIGNATED BY A . NO DEVIATIONS FROM RESISTANCE, WATTAGE, AND VOLTAGE RATINGS MAY

BE MADE FOR REPLACEMENT ITEMS DESIGNATED BY A .

Schematic

Location Part No. Description Schematic

Location Part No. Description

Note: Schematic part location numbers may not always match with the part descriptions.

The part descriptions are correct and should be used.

CAPACITORS RESISTORS

– 11 –

Schematic

Location Part No. Description

CAPACITORS

C016 CK1E105KGMBNG CERAMIC 1U K 25V

C017 CEXLB1E102VEJ ELECT 1000U M 25V

CE1E102MZVANC ELECT 1000U M 25V

C019 CK1A105KLZBNG CERAMIC 1U K 10V

C020 CK1H104KLZBNG CERAMIC 0.1U K 50V

C021 CK1A105KLZBNG CERAMIC 1U K 10V

C022 CK1A105KLZBNG CERAMIC 1U K 10V

C023 CK1A105KLZBNG CERAMIC 1U K 10V

C024 CK1E474KLZBNG CERAMIC 0.47U K 25V

C025 CK1H104KLZBNG CERAMIC 0.1U K 50V

C026 CK1H104KLZBNG CERAMIC 0.1U K 50V

C027 CK1E224KLZBNG CERAMIC 0.22U K 25V

C028 CK1A105KLZBNG CERAMIC 1U K 10V

C029 CK1E474KLZBNG CERAMIC 0.47U K 25V

C030 CK1H104KLZBNG CERAMIC 0.1U K 50V

C031 CEXLB1H100VEJ ELECT 10U M 50V

CE1H100MZVALC ELECT 10U M 50V

C032 CK1E105KGMBNG CERAMIC 1U K 25V

C033 CK1A105KLZBNG CERAMIC 1U K 10V

C034 CK1A105KLZBNG CERAMIC 1U K 10V

C035 CK1A105KLZBNG CERAMIC 1U K 10V

C038 CK1A105KLZBNG CERAMIC 1U K 10V

C039 CK1A105KLZBNG CERAMIC 1U K 10V

C040 CK1E474KLZBNG CERAMIC 0.47U K 25V

C041 CK1H104KLZBNG CERAMIC 0.1U K 50V

C042 CK1H104KLZBNG CERAMIC 0.1U K 50V

C043 CK1E224KLZBNG CERAMIC 0.22U K 25V

C044 CK1E474KLZBNG CERAMIC 0.47U K 25V

C045 CK1H104KLZBNG CERAMIC 0.1U K 50V

C046 CK1H104KLZBNG CERAMIC 0.1U K 50V

C047 CK1E105KGMBNG CERAMIC 1U K 25V

C050 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C800 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C801 CK1H104KLZBNG CERAMIC 0.1U K 50V

C802 CK1A105KLZBNG CERAMIC 1U K 10V

C803 CK1H104KLZBNG CERAMIC 0.1U K 50V

C806 CEXLB0J221VDJ ELECT 220U M 6.3V

C808 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C809 CK1A105KLZBNG CERAMIC 1U K 10V

C813 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C820 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C821 CC1H180JLZCNG CERAMIC 18P J 50V

C822 CC1H220JLZCNG CERAMIC 22P J 50V

C1000 CEXLB1H4R7VDJ ELECT 4.7 U M 50V

C1002 CK1A105KLZBNG CERAMIC 1U K 10V

C1004 CK1A105KLZBNG CERAMIC 1U K 10V

C1006 CK1A105KLZBNG CERAMIC 1U K 10V

C1009 CK1A105KLZBNG CERAMIC 1U K 10V

C1010 CK1A105KLZBNG CERAMIC 1U K 10V

C1012 CK1A105KLZBNG CERAMIC 1U K 10V

C1014 CK1A105KLZBNG CERAMIC 1U K 10V

C1016 CK1A105KLZBNG CERAMIC 1U K 10V

C1025 CC1H471JLZCNG CERAMIC 470P J 50V

C1201 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C1610 CC1H221JLZCNG CERAMIC 220P J 50V

C1611 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C1612 CK1A105KLZBNG CERAMIC 1U K 10V

C1613 CK1E103KMNBNG CERAMIC 0.01U K 25V

C1614 CK1H103KLZBNG CERAMIC 0.01U K 50V

C1615 CK1H103KLZBNG CERAMIC 0.01U K 50V

C1617 CK1H103KLZBNG CERAMIC 0.01U K 50V

C1618 CK1E103KMNBNG CERAMIC 0.01U K 25V

C1619 CK1A105KLZBNG CERAMIC 1U K 10V

C1620 CEXLB0J102VDJ ELECT 1000U M 6.3V

C1621 CK1A105KLZBNG CERAMIC 1U K 10V

C1623 CC1H331JLZCNG CERAMIC 330P J 50V

C1625 CEXLB0J222VEJ ELECT 2200U M 6.3V

C1625 CE0J222MZVALC ELECT 2200U M 6.3V

C1631 CEXLB0J221VDJ ELECT 220U M 6.3V

C1634 CEXLB0J102VDJ ELECT 1000U M 6.3V

C1636 CK1H563KLZBNG CERAMIC 0.056U K 50V

C1637 CK1H333KLZBNG CERAMIC 0.033U K 50V

C1642 CK1A105KLZBNG CERAMIC 1U K 10V

C1644 CEXLB0J102VDJ ELECT 1000U M 6.3V

C1645 CK1H333KLZBNG CERAMIC 0.033U K 50V

C1651 CEXLB0J221VDJ ELECT 220U M 6.3V

C1660 CEXLB1C101VDJ ELECT 100U M 16V

C1664 CEXLB1C101VDJ ELECT 100U M 16V

C1672 CEXLB1V471VDJ ELECT 470U M 35V

C1674 CEXLB1E102VEJ ELECT 1000U M 25V

CE1E102MZVANC ELECT 1000U M 25V

C1675 CK1H104KLZBNG CERAMIC 0.1U K 50V

C1680 CK1A105KLZBNG CERAMIC 1U K 10V

C1681 CC1H221JLZCNG CERAMIC 220P J 50V

C1693 CC1H102JLZCNG CERAMIC 1000P J 50V

C1801 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C1811 CK1H102KLZBNG CERAMIC 1000P K 50V

C1816 CK0J106KGMBNG CERAMIC 10U Z 6.3V

C2403 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C2404 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C2405 CK1A105KLZBNG CERAMIC 1U K 10V

C2407 CK1A105KLZBNG CERAMIC 1U K 10V

C2409 CC1H101JLZCNG CERAMIC 100P J 50V

C2410 CC1H101JLZCNG CERAMIC 100P J 50V

C2416 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C2417 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C2418 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C3900 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C3902 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C3904 CK0J106KGMBNG CERAMIC 10U Z 6.3V

C5501 CK0J106KGMBNG CERAMIC 10U Z 6.3V

C5503 CK0J106KGMBNG CERAMIC 10U Z 6.3V

C5504 CK0J105KMNBNG CERAMIC 1U K 6.3

C5505 CK0J105KMNBNG CERAMIC 1U K 6.3

C5506 CK0J105KMNBNG CERAMIC 1U K 6.3

C5507 CK0J105KMNBNG CERAMIC 1U K 6.3

C5508 CK0J105KMNBNG CERAMIC 1U K 6.3

C5509 CK0J106KGMBNG CERAMIC 10U Z 6.3V

C5510 CK0J105KMNBNG CERAMIC 1U K 6.3

C5511 CC1H221JLZCNG CERAMIC 220P J 50V

C5512 CK0J105KMNBNG CERAMIC 1U K 6.3

Schematic

Location Part No. Description

– 12 –

Schematic

Location Part No. Description Schematic

Location Part No. Description

C5513 CK0J105KMNBNG CERAMIC 1U K 6.3

C5517 CK0J106KGMBNG CERAMIC 10U Z 6.3V

C5518 CK0J105KMNBNG CERAMIC 1U K 6.3

C5519 CK0J105KMNBNG CERAMIC 1U K 6.3

C5521 CK0J105KMNBNG CERAMIC 1U K 6.3

C5523 CK0J476KGBBNG CERAMIC 47U M 6 .3V

C5524 CK0J106KGMBNG CERAMIC 10U Z 6.3V

C5525 CK0J106KGMBNG CERAMIC 10U Z 6.3V

C5526 CK0J105KMNBNG CERAMIC 1U K 6.3

C5527 CK0J105KMNBNG CERAMIC 1U K 6.3

C5529 CK0J105KMNBNG CERAMIC 1U K 6.3

C5530 CK0J105KMNBNG CERAMIC 1U K 6.3

C5532 CK0J105KMNBNG CERAMIC 1U K 6.3

C5534 CK0J105KMNBNG CERAMIC 1U K 6.3

C5535 CK0J105KMNBNG CERAMIC 1U K 6.3

C5536 CK0J106KGMBNG CERAMIC 10U Z 6.3V

C5537 CK0J105KMNBNG CERAMIC 1U K 6.3

C5538 CK0J106KGMBNG CERAMIC 10U Z 6.3V

C5539 CK0J105KMNBNG CERAMIC 1U K 6.3

C5540 CC1H101JLZCNG CERAMIC 100P J 50V

C5541 CK1H102KLZBNG CERAMIC 1000P K 50V

C5542 CK1H102KLZBNG CERAMIC 1000P K 50V

C5544 CK1E103KMNBNG CERAMIC 0.01U K 25V

C5546 CK0J105KMNBNG CERAMIC 1U K 6.3

C5548 CK1C104KMNBNG CERAMIC 0.1U K 16V

C5549 CK1E103KMNBNG CERAMIC 0.01U K 25V

C5550 CK1E103KMNBNG CERAMIC 0.01U K 25V

C5551 CK1E103KMNBNG CERAMIC 0.01U K 25V

C5552 CK0J105KMNBNG CERAMIC 1U K 6.3

C5553 CK1C104KMNBNG CERAMIC 0.1U K 16V

C5555 CK0J105KMNBNG CERAMIC 1U K 6.3

C5556 CK1C104KMNBNG CERAMIC 0.1U K 16V

C5557 CK1E103KMNBNG CERAMIC 0.01U K 25V

C5558 CK0J105KMNBNG CERAMIC 1U K 6.3

C5559 CK0J105KMNBNG CERAMIC 1U K 6.3

C5560 CK0J106KGMBNG CERAMIC 10U Z 6.3V

C5561 CK0J105KMNBNG CERAMIC 1U K 6.3

C5562 CK0J106KGMBNG CERAMIC 10U Z 6.3V

C5564 CK0J105KMNBNG CERAMIC 1U K 6.3

C5565 CK0J105KMNBNG CERAMIC 1U K 6.3

C5567 CK1E103KMNBNG CERAMIC 0.01U K 25V

C5568 CK1E103KMNBNG CERAMIC 0.01U K 25V

C5569 CK0J105KMNBNG CERAMIC 1U K 6.3

C5570 CK0J105KMNBNG CERAMIC 1U K 6.3

C5571 CK1E103KMNBNG CERAMIC 0.01U K 25V

C5572 CK0J105KMNBNG CERAMIC 1U K 6.3

C5573 CK0J105KMNBNG CERAMIC 1U K 6.3

C5574 CK0J105KMNBNG CERAMIC 1U K 6.3

C5575 CK1E103KMNBNG CERAMIC 0.01U K 25V

C5576 CK0J105KMNBNG CERAMIC 1U K 6.3

C5577 CK0J105KMNBNG CERAMIC 1U K 6.3

C5578 CK0J105KMNBNG CERAMIC 1U K 6.3

C5579 CK0J105KMNBNG CERAMIC 1U K 6.3

C5580 CK0J105KMNBNG CERAMIC 1U K 6.3

C5581 CK1C104KMNBNG CERAMIC 0.1U K 16V

C5582 CK0J105KMNBNG CERAMIC 1U K 6.3

C5583 CK0J105KMNBNG CERAMIC 1U K 6.3

C5584 CK1E103KMNBNG CERAMIC 0.01U K 25V

C5585 CK0J105KMNBNG CERAMIC 1U K 6.3

C5586 CK0J105KMNBNG CERAMIC 1U K 6.3

C5587 CC1H120JLZCNG CERAMIC 12P J 50V

C5588 CK0J105KMNBNG CERAMIC 1U K 6.3

C5589 CK0J105KMNBNG CERAMIC 1U K 6.3

C5590 CK0J105KMNBNG CERAMIC 1U K 6.3

C5591 CK1C104KMNBNG CERAMIC 0.1U K 16V

C5592 CK1C104KMNBNG CERAMIC 0.1U K 16V

C5593 CK0J106KGMBNG CERAMIC 10U Z 6.3V

C5594 CK0J106KGMBNG CERAMIC 10U Z 6.3V

C5595 CK0J106KGMBNG CERAMIC 10U Z 6.3V

C5597 CK1C104KMNBNG CERAMIC 0.1U K 16V

C5598 CK1C104KMNBNG CERAMIC 0.1U K 16V

C5600 CK1C104KMNBNG CERAMIC 0.1U K 16V

C5601 CK1C104KMNBNG CERAMIC 0.1U K 16V

C5602 CK1C104KMNBNG CERAMIC 0.1U K 16V

C5603 CK1C104KMNBNG CERAMIC 0.1U K 16V

C5604 CK1C104KMNBNG CERAMIC 0.1U K 16V

C5605 CK1C104KMNBNG CERAMIC 0.1U K 16V

C5606 CK1C104KMNBNG CERAMIC 0.1U K 16V

C5607 CK1C104KMNBNG CERAMIC 0.1U K 16V

C5608 CK0J105KMNBNG CERAMIC 1U K 6.3

C5609 CK0J105KMNBNG CERAMIC 1U K 6.3

C5610 CK0J105KMNBNG CERAMIC 1U K 6.3

C5611 CK0J106KGMBNG CERAMIC 10U Z 6.3V

C5614 CK1E103KMNBNG CERAMIC 0.01U K 25V

C5616 CK0J105KMNBNG CERAMIC 1U K 6.3

C5617 CK1C104KMNBNG CERAMIC 0.1U K 16V

C5618 CK0J105KMNBNG CERAMIC 1U K 6.3

C5619 CK0J105KMNBNG CERAMIC 1U K 6.3

C5620 CK0J106KGMBNG CERAMIC 10U Z 6.3V

C5621 CK0J106KGMBNG CERAMIC 10U Z 6.3V

C5628 CC1H2R0CLZCNG CERAMIC 2P C 50V

C5629 CC1H1R0CLZCNG CERAMIC 1P C 50V

C5650 CC1H470JLZCNG CERAMIC 47P J 50V

C5651 CC1H470JLZCNG CERAMIC 47P J 50V

C5652 CC1H470JLZCNG CERAMIC 47P J 50V

C5653 CC1H470JLZCNG CERAMIC 47P J 50V

C5654 CC1H470JLZCNG CERAMIC 47P J 50V

C5655 CC1H470JLZCNG CERAMIC 47P J 50V

C5656 CC1H470JLZCNG CERAMIC 47P J 50V

C5657 CC1H470JLZCNG CERAMIC 47P J 50V

C5658 CC1H470JLZCNG CERAMIC 47P J 50V

C5659 CC1H470JLZCNG CERAMIC 47P J 50V

C5660 CC1H470JLZCNG CERAMIC 47P J 50V

C5661 CC1H470JLZCNG CERAMIC 47P J 50V

C5702 CK1C104KMNBNG CERAMIC 0.1U K 16V

C5703 CK0J106KGMBNG CERAMIC 10U Z 6.3V

C5704 CK0J105KMNBNG CERAMIC 1U K 6.3

C5705 CK1C104KMNBNG CERAMIC 0.1U K 16V

C5706 CK0J105KMNBNG CERAMIC 1U K 6.3

C5707 CK1C104KMNBNG CERAMIC 0.1U K 16V

C5708 CK1C104KMNBNG CERAMIC 0.1U K 16V

– 13 –

Schematic

Location Part No. Description Schematic

Location Part No. Description

C5709 CK0J106KGMBNG CERAMIC 10U Z 6.3V

C5710 CK0J105KMNBNG CERAMIC 1U K 6.3

C5711 CK1C104KMNBNG CERAMIC 0.1U K 16V

C5712 CK0J105KMNBNG CERAMIC 1U K 6.3

C5713 CK0J105KMNBNG CERAMIC 1U K 6.3

C5714 CK1C104KMNBNG CERAMIC 0.1U K 16V

C5715 CK0J105KMNBNG CERAMIC 1U K 6.3

C5716 CK1C104KMNBNG CERAMIC 0.1U K 16V

C5717 CK1E103KMNBNG CERAMIC 0.01U K 25V

C5718 CK1H333KLZBNG CERAMIC 0.033U K 50V

C5731 CEXLB0J221VDJ ELECT 220U M 6.3V

C5734 CEXLB0J102VDJ ELECT 1000U M 6.3V

C5735 CK1H333KLZBNG CERAMIC 0.033U K 50V

C5736 CEXLB0J102VDJ ELECT 1000U M 6.3V

C5751 CEXLB1V470VEJ ELECT 47U M 35V

CE1V470MZVALC ELECT 47U M 35V

C5755 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C5756 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C5802 CC1H680JLZCNG CERAMIC 68P J 50V

C5803 CC1H680JLZCNG CERAMIC 68P J 50V

C5804 CC1H680JLZCNG CERAMIC 68P J 50V

C5806 CC1H270JLZCNG CERAMIC 27P J 50V

C5807 CC1H270JLZCNG CERAMIC 27P J 50V

C5808 CC1H270JLZCNG CERAMIC 27P J 50V

C5810 CC1H5R0CLZCNG CERAMIC 5P C 50V

C5811 CC1H5R0CLZCNG CERAMIC 5P C 50V

C5812 CC1H5R0CLZCNG CERAMIC 5P C 50V

C5814 CC1H120JLZCNG CERAMIC 12P J 50V

C5815 CC1H120JLZCNG CERAMIC 12P J 50V

C5816 CC1H120JLZCNG CERAMIC 12P J 50V

C5818 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C5819 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C5820 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C5821 CK1H104KLZBNG CERAMIC 0.1U K 50V

C5822 CEXLB1H100VDJ ELECT 10U M 50V

C5823 CEXLB1H100VDJ ELECT 10U M 50V

C5901 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C5902 CK1E224KLZBNG CERAMIC 0.22U K 25V

C6101 CK1H103KLZBNG CERAMIC 0.01U K 50V

C6102 CK1H103KLZBNG CERAMIC 0.01U K 50V

C6103 CC1H470JLZCNG CERAMIC 47P J 50V

C6105 CC1H470JLZCNG CERAMIC 47P J 50V

C6106 CC1H470JLZCNG CERAMIC 47P J 50V

C6110 CEXLB0J102VDJ ELECT 1000U M 6.3V

C6111 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C6112 CK1H104KLZBNG CERAMIC 0.1U K 50V

C6115 CK1H103KLZBNG CERAMIC 0.01U K 50V

C6130 CK1H102KLZBNG CERAMIC 1000P K 50V

C6131 CK1H102KLZBNG CERAMIC 1000P K 50V

C6133 CC1H120JLZCNG CERAMIC 12P J 50V

C6134 CC1H120JLZCNG CERAMIC 12P J 50V

C6135 RGFR000ZTCANL MT-GLAZE 0.000 ZA 1 /10W

C6136 RGFR000ZTCANL MT-GLAZE 0.000 ZA 1 /10W

C6207 CEXLB1H100VDJ ELECT 10U M 50V

C6208 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C6223 CK1A105KLZBNG CERAMIC 1U K 10V

C6250 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C6251 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C6252 CEXLB1V470VDJ ELECT 47U M 35V

C6253 CK1H103KLZBNG CERAMIC 0.01U K 50V

C6254 CK1H103KLZBNG CERAMIC 0.01U K 50V

C6255 CK0J475KLZBNG CERAMIC 4.7U K 6.3V

C6256 CK0J475KLZBNG CERAMIC 4.7U K 6.3V

C6257 CK0J106KGMBNG CERAMIC 10U Z 6.3V

C6258 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C6259 CK0J106KGMBNG CERAMIC 10U Z 6.3V

C6260 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C6270 CEXLB1H100VEJ ELECT 10U M 50V

CE1H100MZVALC ELECT 10U M 50V

C6272 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C6274 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C6275 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C6276 CEXLB1H100VEJ ELECT 10U M 50V

CE1H100MZVALC ELECT 10U M 50V

C6277 CEXLB1H100VEJ ELECT 10U M 50V

CE1H100MZVALC ELECT 10U M 50V

C6278 CK1A105KLZBNG CERAMIC 1U K 10V

C6279 CK1A105KLZBNG CERAMIC 1U K 10V

C6301 CC1H471JLZCNG CERAMIC 470P J 50V

C6302 CC1H680JLZCNG CERAMIC 68P J 50V

C6303 CC1H680JLZCNG CERAMIC 68P J 50V

C6304 CC1H680JLZCNG CERAMIC 68P J 50V

C6305 CC1H471JLZCNG CERAMIC 470P J 50V

C6306 CC1H680JLZCNG CERAMIC 68P J 50V

C6309 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C6310 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C6312 CEXLB1H100VDJ ELECT 10U M 50V

C6321 CK1A105KLZBNG CERAMIC 1U K 10V

C6322 CK1A105KLZBNG CERAMIC 1U K 10V

C6324 CK1A105KLZBNG CERAMIC 1U K 10V

C6501 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C6502 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C6503 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C6531 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C6533 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C6561 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C6563 CK1H104ZLZFNG CERAMIC 0.1U Z 50V

C6605 CK1A105KLZBNG CERAMIC 1U K 10V

C6606 CC1H220JLZCNG CERAMIC 22P J 50V

C6607 CC1H220JLZCNG CERAMIC 22P J 50V

C6609 CEXLB1V471VDJ ELECT 470U M 35V

C6611 CK1E103KMNBNG CERAMIC 0.01U K 25V

– 14 –

Schematic

Location Part No. Description Schematic

Location Part No. Description

DIODES

D001 DD1SS352——G DIODE 1SS352-(TPH3)