Sarin Energy ML01 User manual

SARINEnergy.com 855-997-2746 | [e-mail] | 1
INSTALLATION INSTRUCTIONS
LED Mirror - ML01
INSTALLATION STEPS
STEP 1
CUT OFF THE MAIN POWER SUPPLY.
BEFORE YOU START, HERE IS SOME IMPORTANT INFORMATION.
IMPORTANT
to prevent personal injury or damage to the product; If the glass is
broken, please stop using it and replace it from agent or manufacturer.
●Ensure the mounting surface is dry and strong enough to bear four
●Special care should be taken when drilling walls to avoid hidden
●The product covers the outlet box and the wirings after installation.
●Wipe clean with a soft, dry cloth. Never use abrasives or chemical
●Please put a soft cushion under the mirror while you take the mirror
down from the wall.
MAINTENANCE
times the weight of the product for the safe fitting.
pipes or electrical cables.
INSTALLATION INSTRUCTION
●This product contains glass parts. Take care while fitting or handling
TOOLS REQUIRED
Description
Drill
Parts Image
Cross Head
Screwdriver
Description
Tape Measure
Pencil
Parts Image
Spirit Level
Hammer
WARNING: Installation must be performed
by a qualified licensed electrician.
DANGER: Before installation, make sure
the main power is cut off.
cleaners.
STEP 2 STEP 3
STEP 2
Place the metal 'Z' bar against the wall and use a level to make sure that it is level.
Use a pencil to mark the position of the screw holes. Note: The part of the 'Z' bar
sticking out from the wall will be on top when installed.
STEP 3
Drill holes where the pencil marks are and put in the wall plugs for 'Z' bar.
STEP 4
Align the 'Z' bar with the wall plugs. The lip sticking out from the wall should be on top.
Screw the metal 'Z' bar onto the wall with the mounting screws supplied.
STEP 5
Place the mirror nearby so that it's close enough to connect the wires to the main
power supply.

SARINEnergy.com
INSTALLATION INSTRUCTIONS
855-997-2746 | [e-mail] | 2
LED Mirror - ML01
INSTALLATION STEPS
STEP
1
CUT
OFF THE MAIN POWER SUPPLY.
BEFORE YOU START, HERE IS SOME IMPORTANT INFORMATION.
IMPORTANT
to prevent personal injury or damage to the product; If the glass is
broken, please stop using it and replace it from agent or manufacturer.
●Ensure the mounting surface is dry and strong enough to bear four
●Special care should be taken when drilling walls to avoid hidden
●The product covers the outlet box and the wirings after installation.
●Wipe clean with a soft, dry cloth. Never use abrasives or chemical
●Please put a soft cushion under the mirror while you take the mirror
down from the wall.
MAINTENANCE
times the weight of the product for the safe fitting.
pipes or electrical cables.
INSTALLATION INSTRUCTION
●This product contains glass parts. Take care while fitting or handling
TOOLS REQUIRED
Description
Drill
Parts Image
Cross Head
Screwdriver
Description
Tape Measure
Pencil
Parts Image
Spirit Level
Hammer
WARNING: Installation must be performed
by a qualified licensed electrician.
DANGER: Before installation, make sure
the main power is cut off.
cleaners.
STEP 2 STEP 3
STEP
2
Place
the metal 'Z' bar against the wall and use a level to make sure that it is level.
Use a pencil to
mark the position of the screw holes. Note: The part of the 'Z' bar
sticking out from the wall will be on top when installed.
STEP
3
Drill
holes where the pencil marks are and put in the wall plugs for 'Z' bar.
STEP
4
Align the 'Z' bar with the wall plugs. The lip sticking out from the wall should be on top.
S
crew the metal 'Z' bar onto the wall with the mounting screws supplied.
STEP
5
Place
the mirror nearby so that it's close enough to connect the wires to the main
power supply.