SASSOON VS7890A User manual

Model VS7890A
I-TRIM PRECISE STUBBLE TRIMMER

IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, especially when children are
present, basic safety instructions should always be followed,
including the following:
Polythene bags over product or package may be dangerous. To
avoid danger of suffocation, keep this wrapper away from babies
and children. This bag is not a toy.
DANGER: When the unit is used in a bathroom, unplug after use
since the proximity of water presents a hazard even when the unit
is switched off.
WARNING: Do not use or leave the appliance or AC
power adaptor in a position where it can become wet or
there is danger of it falling into a basin or other vessels
containing water.
• Take care to avoid contact between the moving blades of the unit
and the skin, paying particular attention to the face, neck and
hands.
• This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety.
• Children should be supervised to ensure that they do not play
with the appliance.
IMPORTANT: Always unplug the appliance when not in use or before
cleaning. Do not leave unattended when plugged in or switched on.
Do not place on any heat sensitive surface.
• Do not use any attachments other than those supplied by Conair
Australia Pty Ltd.
• Use this appliance only for its intended use as described within
this instruction booklet.

• Always unplug the appliance when fully charged.
• This appliance is not intended for commercial use.
• Never drop or insert any object into any opening.
• Do not use the appliance with damaged or broken attachment
combs or with any teeth missing from the blades, as injury may
occur.
• Do not place appliance on any surface while it is operating.
• Do not use outdoors or operate where aerosol (spray) products
are being used or where oxygen is being administered.
• Keep the cord away from heated surfaces.
• Do not use this appliance if it is damaged. In the event of
damage, discontinue use immediately and contact your dealer for
instructions on returning it for examination or exchange. If the
supply cord is damaged, it must be replaced by the manufacturer,
its service agent or similarly qualified person in order to avoid a
hazard.
• Never twist or pull on the trimmer adaptor cord.
• After use do not wrap the cord around the appliance as in time
this may cause the cord to fracture. Coil cord loosely by the side
of the appliance in storage.
• Always ensure that the voltage to be used corresponds to the
voltage marked on the unit.
• For additional protection, the installation of a residual current
device (RCD) with a rated operating current not exceeding 30mA is
advisable in the electrical current circuit supplying the bathroom.
Ask your installer for advice.

I-TRIM PRECISE
AUTOMATIC ALL-IN-ONE DC MOTOR STUBBLE TRIMMER
Thank you for purchasing the VS For Men i-trim precise Stubble
Trimmer, an automatic all-in-one DC motor stubble trimmer that
provides the ultimate in stubble control.
This next generation design stubble trimmer features a unique
contouring flex head with exclusive blade design that adjusts
flawlessly to the contours of the face. Its’ advanced design provides
more precise and even results, minimizes pressure for less skin
irritation and provides exceptional accuracy for perfect stubble
results, every time.
The i-trim precise delivers VS For Men’s best cutting performance
by combining ‘Hard Like Diamond’ (HLD) carbon coated stainless
steel blades with titanium and a high performance professional DC
motor to provide precision control for exact stubble.
FEATURES
1. Innovative motorised comb
guide system with up and
down selections
2. 1 integrated motorised
stubble comb guide that
delivers the ultimate in
length consistency for
effortless ease
3. Unique contouring flex
head with exclusive blade
design minimizes pressure,
for less irritation, and exact
precision control
4. Trimmer blades – ‘Hard Like
Diamond’ (HLD) carbon
coated stainless steel blades
with Titanium
5. On/Off button
6. LCD display shows:
7. Selected cutting
length in mm
8. Battery life remaining /
charging indicator
9. Cord/cordless design
10. AC power adaptor
11. Cleaning brush
12. Lubricating oil

2
4
3
5
6
11
12
9
10
1
7
8

INSTRUCTIONS FOR USE
• A plastic cover has been placed over the adaptor plug to protect
it from damage during transportation. Remove the plastic cover
before inserting into a suitable power outlet.
• Always inspect the appliance before use to ensure the cutting head
is free from hair and debris, and is running smoothly.
• Ensure the appliance is switched off before plugging into a suitable
power outlet.
CHARGING THE TRIMMER
(FOR CORDLESS OPERATION)
To charge the appliance, place the adaptor charging cord directly
into the base of the trimmer.
1. Plug the AC power adaptor into a 100v – 240v power supply.
2. When the appliance is switched off, plug the charging cord
directly into the base of the trimmer.
3. Switch the adaptor on. The LCD display will then illuminate and
the charging indicator will appear in the LCD display. Always
check the charging indicator illuminates, so you know you have
correctly inserted the adaptor charging cord into the base of the
trimmer.
IMPORTANT: Before using the appliance for the first time, charge
for a full 16 hour continuous charge.
After the first charge, the trimmer has a 90 minute charge and
60 minute run time, plus the 5 minute quick charge and 3 minute
run time. Maximum battery capacity will only be reached after
3 charging and discharging cycles.
In order to maintain optimum capacity of the rechargeable
batteries, every 3 months the trimmer should be charged for a
full 16 hour continuous charge.

4. The blue LCD will always stay illuminated and the charging
indicator in the LCD display will always be flashing when the
product is charging. When the product is fully charged, the
charging indicator will be solid and no longer flashing – this
indicates that a full charge has been reached.
5. A full charge will supply enough power for minimum 60 minutes
use. The remaining battery life is shown in the LCD display. The 5
minutes quick charge function will provide 3 minutes use.
CORDED USE – OPERATION WITH POWER CORD
1. Plug the AC power adaptor into a 100v – 240v power supply.
2. When the appliance is switched off, plug the charging cord
directly into the base of the trimmer.
3. Switch the adaptor on, and the trimmer can now be used in
corded operation.
NOTE – If battery power is weak, wait about 2 minutes before
pressing the on/off button.
24 Ultra Precise Cutting Length Settings (0.4mm to 5mm)
The innovative i-trim precise Stubble Trimmer uses an integrated
stubble comb guide with 24 ultra precise control settings eliminating
the need for charging and storing different attachment combs.
The cutting guide is motorised for easy one touch adjustment and
features an LCD display for confirmation of the length setting
selected. When you select your required length, the length setting
will then remain displayed in the LCD screen.
1. Use the cutting length setting buttons on the trimmer to adjust
the motorised stubble comb guide.
2. Press the power on button to activate the trimmer motor.
3. Press the up or down arrow buttons to select the required length
setting in 0.2mm increments from 0.4mm through to 5mm (NB –
the trimmer will stop while the comb guide is being adjusted).

STARTING AND USING YOUR I-TRIM PRECISE
1. Press the on/off button to activate the trimmer.
2. When the trimmer is switched on, the battery indicator in the LCD
display will cycle through a few times (approx 5 times) before the
remaining battery life is displayed.
3. Press the up or down arrow buttons to adjust and set the cutting
length. Pressing one of these buttons will stop the trimmer motor.
It is always suggested to start cutting with a longer length first,
then trim again if the length is longer than desired.
4. Hold the trimmer against the hair, the teeth of the comb guide
should be pointing upwards and should be flat against the face.
The unique contouring flex head with excusive blade design
allows for trimming at any angle – it perfectly adjusts to the
contours of your face for precision stubble results, every time,
whilst the integrated stubble comb guide helps to avoid uneven
cuts, by providing direction and helping you to hold the trimmer
comfortably on the face.
5. Move the trimmer upwards through the hair, a little at a time,
with and against the direction of hair growth, whichever is most
comfortable, as most men have hair growing in many different
directions.
6. The i-trim precise will work most effectively when cutting
through the hair at its own speed – never force the trimmer. You
may experience a little resistance around the moustache area,
where hair is thicker and grows in many different directions. This
is completely normal.
7. Never switch the trimmer off whilst in the hair.
8. To turn the trimmer off:
Either: Press and hold the on/off button for more than 2 seconds,
the trimmer will shut down completely and the cutting guide will
return to its original position;
Or: Press the on/off button for less than 2 seconds, only the motor
will turn off, but the display will remain lit for 15 seconds. After 15
seconds you still have 5 minutes to change the cutting length.

After 5 minutes the trimmer turns itself off and the cutting guide comb
will return to its original position next time you activate the trimmer.
USING THE STUBBLE COMB GUIDE
Your i-trim precise comes assembled with the integrated motorised
all-in-one stubble comb guide already installed. The integrated
stubble comb guide allows you to change the cutting length of your
trimmer with ease. You’ll need to experiment to find your preferred
length, but as a guide, 0.4mm will give you an ultra close, short
shadow stubble effect, whilst 2mm will give you a longer designer
stubble look and 3.4mm+ will give you a longer, more rugged look
(short beard).
IMPORTANT: Always detach and attach the integrated stubble comb
guide BEFORE turning the trimmer on.
Always ensure when using the trimmer that the integrated stubble
comb guide is correctly positioned in place. Check this by pushing
the comb guide gently downwards to ensure it is secured in place.
Using The Trimmer Without The Comb Guide
Using the trimmer without the comb guide is
ideal for detailing/shaping and general tidying
of edges around your stubble, sideburns and
moustache.
1. To detach the comb guide, gently hold the
trimmer in one hand and with your thumb and
index finger, push the comb guide up on each
side (Fig.1).
2. Flip the comb guide to the back of the unit and
lock it into position by clicking it securely onto
the fastener on the back of the handle (Fig.2).
IMPORTANT: When using the trimmer without the stubble comb
guide, the cutting length will be below 0.4mm. The length setting
show on the LCD screen will no longer be relevant when the comb
guide is detached.
Fig. 2
Fig. 1

HOW TO CREATE DIFFERENT LOOKS USING THE I-TRIM PRECISE
A popular and most recent trend in men’s grooming is the stubble
look – a well groomed light hint of facial hair. The stubble look is a
rugged way to add interest to a man’s face without sporting a full
beard – it can help make a man’s face look romantic, sophisticated,
cool rugged or even refined, depending on which way you wear it.
It is one of the lasting hints of facial hair trends that works for so
many different men.
Maintaining a stubble look requires regular grooming with the i-trim
precise, to ensure that you don’t get a patchy or uneven appearance.
It is recommended to trim every couple of days to keep your shadow
effect from sprouting into a full beard. The key to staying trimmed
is paying attention to how fast your facial hair grows. The faster
you can grow a beard, the quicker you’ll need to keep up with your
stubble to ensure it stays shaped – stubble is an ongoing process of
upkeep, so you can’t just shape it and leave it.
NB – Use on clean, dry hair. If possible when using for the first time,
try and grow your facial hair for at least 4 days before cutting. This
will give you a better result, as your facial hair will feel thicker.
To create a short, shadow stubble look:
1. If your hair is already quite short, set the motorised comb guide
to 0.4mm trimming length. If your hair is quite long, thic k and
coarse, pre-trim the hair using a longer length setting, such as
5mm, then once all hair has been trimmed, set the motorised
comb guide to 0.4mm length.
2. Move the trimmer upwards through the hair, a little at a time,
with and against the direction of hair growth, whichever is
most comfortable, as most men have hair growing in various
directions.
3. For a close finish around the sideburns and cheeks, detach the
stubble comb guide (refer to ‘Using The Trimmer Without The
Comb Guide’ for further information) and turn the trimmer
over so that the blades are closest to the face. Trim around the

sideburns, cheeks and edge of your stubble, taking care around
the sideburns and edges of your stubble so that you do not trim
the hair too short.
To create a longer, designer stubble look (mid-length stubble):
1. If your hair is already quite short, set the motorised comb guide to
2mm trimming length. If your hair is quite long, thick and coarse,
pre-trim the hair using a longer length setting, such as 5mm, then
once all hair has been trimmed, set the motorised comb guide to
2mm length.
2. Move the trimmer upwards through the hair, a little at a time,
with and against the direction of hair growth, whichever is
most comfortable, as most men have hair growing in various
directions.
3. For a close finish around the sideburns and cheeks, detach the
stubble comb guide (refer to ‘Using The Trimmer Without The
Comb Guide’ for further information) and turn the trimmer
over so that the blades are closest to the face. Trim around the
sideburns, cheeks and edge of your stubble, taking care around
the sideburns and edges of your stubble so that you do not trim
the hair too short.
To create a longer, more rugged look (short beard):
1. If your hair is already quite short, set the motorised comb guide
to 3.4mm trimming length. If your hair is quite long, thick and
coarse, pre-trim the hair using a longer length setting, such as
5mm, then once all hair has been trimmed, set the motorised
comb guide to 3.4mm length.
2. Move the trimmer upwards through the hair, a little at a time,
with and against the direction of hair growth, whichever is
most comfortable, as most men have hair growing in various
directions.
3. For a close finish around the sideburns and cheeks, detach the
stubble comb guide (refer to ‘Using The Trimmer Without The
Comb Guide’ for further information) and turn the trimmer
over so that the blades are closest to the face. Trim around the

sideburns, cheeks and edge of your stubble, taking care around
the sideburns and edges of your stubble so that you do not trim
the hair too short.
To create a longer, beard look:
1. If your hair is already quite short, set the motorised comb guide
at any length between 3.6mm and 5mm trimming length.
2. Move the trimmer upwards through the hair, a little at a time,
with and against the direction of hair growth, whichever is
most comfortable, as most men have hair growing in various
directions.
3. For a close finish around the sideburns and cheeks, detach the
stubble comb guide (refer to ‘Using The Trimmer Without The
Comb Guide’ for further information) and turn the trimmer
over so that the blades are closest to the face. Trim around the
sideburns, cheeks and edge of your stubble, taking care around
the sideburns and edges of your stubble so that you do not trim
the hair too short.

MULTI VOLTAGE
This appliance has a multi voltage feature for worldwide use. The
voltage automatically converts for ease of use from 100v - 240v.
This appliance has an automatic internal converter which will
automatically convert the voltage without the need of a switch.
A suitable plug adaptor will be required, please refer to the chart
below.
Plug adaptor
required
Voltage and
plug adaptors
Country Voltage
setting
British plug:
240V
Ireland, Great Britain, Singapore, South America,
Hong Kong (parts only), Africa (parts only)
240V
European plug:
240V
Asia, Europe, Middle East Noumea, Scandinavia,
South America, Hong Kong (parts only)
240V
Australian and
New Zealand
plug: 240V
Australia, New Zealand 240V
American
plugs: 120V
North America, Japan, Canada
(parts of)
120V

CLEANING AND MAINTENANCE
To maintain optimum performance, the appliance should be cleaned
after each use:
1. Switch the trimmer off and remove the power supply, if
connected.
2. Detach the comb guide by gently lifting the front of the comb
guide from both sides and flipping it over to the back of the
unit, and locking it into position by clicking it securely onto the
fastener on the back of the handle (refer to ‘Using The Trimmer
Without The Comb Guide’ for further information).
3. Using the cleaning brush supplied, brush away any hair and
debris. Do not use a sharp object to clean the trimmer head.
4. To make cleaning even easier, the blades can be removed from
the trimmer and comb guide.
To remove the blades, hold the handle of the trimmer with one
hand, place your thumb underneath the blades and push the
blades up and away from the handle. Place the blades in a secure
place whilst cleaning.
Gently blow away any hair that is trapped beneath the blades.
The blades can also be rinsed under cool running water. ONLY
THE BLADES CAN BE RINSED UNDER THE TAP – THE TRIMMER
SHOULD NEVER BE PLACED UNDER THE TAP OR UNDER RUNNING
WATER.
5. Ensure the blades are dry before re-attaching to the trimmer
body.
6. To replace the blades, ensure the stubble comb guide is detached
and then place the back of the blades back into the cavity on the
top of the trimmer. Press the blades down so that they click into
place.
7. When used regularly, the blades will not need to be oiled.
However, if the blades have been rinsed under the tap or the
trimmer has not been used for a prolonged period of time,
then it is advisable to apply a small amount of lubricating oil
(provided) onto the blades before using. This helps to keep the
blades as sharp as possible.

8. To oil the blades, add a few drops of the oil supplied over the
blades. Switch the trimmer on for a minute and then turn off.
Wipe away any excess oil with a soft cloth. Be careful not to use
too much oil, and don’t oil your trimmer more than necessary.
Oil the blades regularly to maintain optimum performance. This
light, natural oil is similar to oil used in sewing machines, which
can be purchased from your local art and crafts store.
BATTERY DISPOSAL
The appliance contains Nickel Metal-Hydrate batteries. To protect
the environment, the appliance must be disposed of safely at the
end of its useful life. Please take the appliance to a recycling centre,
where the internal rechargeable battery should be removed by a
professional and recycled separately.
For more information about the recycling of electrical and battery
operated appliances, please contact your local council office or your
household waste disposal service

®
Vidal Sassoon and related logos are trademarks of
The Procter & Gamble Company used under licence by Conair
©2012 Conair Corporation USA
Conair Australia Pty Ltd, Suites 20 & 21,
7 Narabang Way, Belrose NSW 2085.
Australia Customer Service Hotline (Australia): 1800 650 263
Customer Service e-mail: [e-mail]
Conair New Zealand Limited, PO BOX 251159, Pakuranga, Auckland
1706 New Zealand
Customer Service Hotline (New Zealand): 0800 266 247
LIMITED THREE YEAR WARRANTY
This product is subject to the express warranty given on the
warranty card included with the product, as may be amended by
reference to and in accordance with the terms of the warranty
cards displayed on VS For Men websitewww.vsformen.com.au 
To make a warranty claim you must retain your proof of purchase.
Further details can be found at www.vsformen.com.au and click on
‘customer service’.