Saturn SX360 User manual
Saturn SX360 IP Camera Quick Guide
The Quick Guide is for quick installing and connecting the Saturn 360 IP Camera. For more details, please refer to
the User’s Manual of the camera in the supplied CD.
Camera’s Connectors (Indoor Only)
NOTE: Check the status of the link indicator and activity indicator LEDs. If the LEDs are unlit, please check
the LAN connection.
Green Link Light indicates good network connection.
Orange Activity Light flashes for network activityindication.
Function Cable (Outdoor Only)
NOTE: It is not recommended to record with the microSD card for 24/7 continuously, as it may not be able to
support long term continuous data read/write. Please contact the manufacturer of the microSD card for
information regarding the reliability and the life expectancy.
Camera Cabling
Please follow the instructions below for cable connections.
Power Connection
Please use a DC 12V power adaptor and plug it to the camera and the power outlet. Alternatively, users can use an
Ethernet cable and connect it to the RJ-45 connector of the camera and a Power Sourcing Equipment (PSE)switch.
NOTE: If PoE is used, make sure PSE is in used in thenetwork.
Ethernet Cable Connection
Connect one end of the Ethernet cable to the RJ-45 connector of the camera, and plug the other end of the cable to
the network switch or PC.
NOTE: In some cases, Ethernet crossover cable might be needed when connecting the camera directly to the
PC.
Before Login to the Camera
A client program will be automatically installed to the PC when connecting to the camera. Before logging in to the
camera, please ensure downloading the ActiveX control is allowed by either changing the ActiveX controls and plug-
ins or setting Internet’s security level to default. For further details, please refer to the User’s Manual in the supplied
CD.
No.
Connector
Pin
Definition
Remarks
1
Power
DC 12V
1
DC 12V
Power connection
2
Reserved
2
RJ-45
-
For network and PoE connections
3
microSD Card Slot
-
Insert the microSD card into the card slot to store videos and snapshots.
Do not remove the microSD card when the camera is powered on.
4
Default Button
-
Press the button with a proper tool for at least 20 seconds to restore the
system.
5
Alarm & Audio I/O
1
Alarm Out +
Alarm connection
2
Alarm Out -
3
Alarm In +
4
Alarm In -
5
GND
Ground connection
6
Audio Out
Two-way audio transmission
7
Audio In
No.
Connector
Pin
Definition
Remarks
1
Audio I/O
Pink
Audio In
Two-way audio transmission
Green
Audio Out
2
Power (DC 12V)
(2-Pin Terminal Block)
Black
DC 12V –
Power connection
Red
DC 12V +
3
Alarm I/O
(4-Pin Terminal Block)
1
Alarm In –
Alarm connection
2
Alarm In +
3
Alarm Out –
4
Alarm Out +
4
GND
-
GND
Ground connection
5
RJ-45
-
For network and PoE connections
-
microSD Card Slot
-
Refer to the Default Button in the table under section Camera’s
Connectors (Indoor Only).
-
Default Button
-
Refer to the microSD Card Slot in the table under section Camera’s
Connectors (Indoor Only).
ActiveX Controls and Plug-ins Settings
Internet Security Level
Step 1: Start the Internet Explorer (IE).
Step 2: Select <Tools> from the main menu of the
browser. Then click on <Internet Options>.
Step 3: Click on the <Security>tab and select
<Internet>, and click on <Custom level> to
change ActiveX settings.
Step 4: Set “ActiveX controls and plug-ins” items to
<Prompt> or <Enable>.
Step 1: Start the Internet Explorer (IE).
Step 2: Select <Tools> from the main menu of the
browser. Then click on <Internet Options>.
Step 3: Click on the <Security> tab and select
<Internet>.
Step 4: Down the page, click <Default Level> and click
on <OK> to confirm the setting. Close the
browser window, and open a new one later for
accessing the IP camera.
Camera Login
The default IP address of the camera is: 192.168.0.250. Therefore, to access the camera for the first time, please set
the IP address of the PC as: 192.168.0.XXX; for example:
IP Address: 192.168.0.100
Subnet Mask: 255.255.255.0
Login ID and Password
Key in the camera’s IP address in the URL bar of the web browser window and hit on“Enter”.
Enter the default username (Admin) and password (1234) in the prompt request dialogue. Note that username is
case sensitive.
Install the ActiveX Control
After connecting to the camera, the request for installing theActiveX control will appear just below the URL bar.
Right click on the information bar, and then click on <Install ActiveX Control…> to permitActiveX control installation.
In the pop-up security warning window, click on <Install> to start downloading Viewer software on thePC.
Click on <Finish> after Viewer installation is completed.
Browser-based Viewer
The main page of the IP camera user interface is shown as the figure below. Please note that function buttons will vary
depending on the camera model.
Saturn SX360 Fisheye IP Camera
Quick Guide
V1.072015
