Sauder Rustic Country 412373 User manual

sauder.com
Panel TV Stand
Rustic Country Collection | Model 412373
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-28
Français pg 29-32
Español pg 33-36
Lot # 531642 07/16/19
Purchased: __________________
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
Share your journey!
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-445-1527.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
It stands. You sit.
A thing of beauty,
this one.

Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
Table of Contents Assembly Tools Required
3
4
5-28
29-32
33-36
37-38
39
WARNING
!
Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or
death. A TV that is too large for the available space might be accidentally pushed or bumped o the furniture, or subject to tip-over.
• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!
• This Sauder unit is designed for use with televisions weighing less than 70 pounds. Never use with a TV that weighs more.
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diagram.
• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)
• Never allow the sides of the TV to extend past the side edges of the TV support surface.
• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.
• Be sure to apply the warning label as instructed in the last assembly step. The label provides important safety related information.
70 lbs.
70 lbs.
18-5/8"
18-5/8"
47-1/2"
47-1/2"
Page 2 www.sauder.com 412373

åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Part Identification Now you know
our ABCs.
A2 TOP SHELF (1)
B MIDDLE SHELF (1)
C BOTTOM SHELF (1)
E CONNECT TUBE (1)
F BACK PANEL (1)
I MIDDLE PANEL (1)
J BACK SUPPORT PANEL (1)
K LEFT DRAWER FRONT (1)
L RIGHT DRAWER FRONT (1)
M LEFT DRAWER PANEL (2)
N RIGHT DRAWER PANEL (2)
O REAR DRAWER PANEL (2)
P BOTTOM DRAWER PANEL (2)
Q2 LEFT LEG FRAME (1)
R2 RIGHT LEG FRAME (1)
S UPPER CONNECT TUBE (1)
T MIDDLE CONNECT TUBE (1)
U LOWER BACK CONNECT TUBE (1)
V LOWER FRONT CONNECT TUBE (1)
W SHORT DECORATIVE METAL (2)
X LONG DECORATIVE METAL (2)
A2
B
C
F
J
K
L
M
N
O
P
Q2
R2
S
T
V
X
I
X
O
P
N
M
W
E
U
Page 3www.sauder.com412373

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
CAM SCREW - 14
CC
LARGE HIDDEN
CAM - 6
AA SMALL HIDDEN
CAM - 8
BB
WOOD DOWEL - 5
DD METAL
BRACKET - 16
EE HEX WRENCH - 1 GG
NUT - 4
HH CASTER - 4 II HANDLE - 2 JJ GLUE - 1 KK
2-15/16" PAN HEAD SCREW - 2
MM 1-3/4" BOLT - 4 NN
1-3/16" MACHINE SCREW - 2
PP
1/2" PAN HEAD SCREW - 40
VV
1/2" MACHINE SCREW - 4
UU
1/2" BOLT - 12
TT
1" FLAT HEAD SCREW - 8
SS
1" PAN HEAD SCREW - 3
RR
1" BOLT - 4
QQ
1/2" FLAT HEAD SCREW - 16
WW
CABINET RAIL SET - 4
Y
(R)
(L)
DRAWER SLIDE SET - 4
Z
(R)
(L)
WARNING LABEL - 1
LL
(Refer to the last step for proper
location and application)
522,68 22,68
70 lbs. 31,75 kg 31,75 kg
L-WRENCH - 1
FF
Page 4 www.sauder.com 412373

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty carton
to avoid scratching your unit or the floor.
å Fasten a CABINET RAIL SET (Y) to both surfaces of the
MIDDLE PANEL (I). Use four 1/2" FLAT HEAD SCREWS (WW).
Page 5www.sauder.com412373
I
Y(L)
Some assembly
(and snacks) required.
These edges
must be even.
F
L
I
P
O
V
E
R
Roller end
Use the second hole
from the roller.
(R)
These edges
must be even.
I
Y
Use the first hole
from the roller.
Roller end
1/2" FLAT HEAD SCREW
(4 used for the RAILS)
WW

å Fasten a CABINET RAIL SET (Y) to the LEG FRAMES (Q2
and R2). Use four 1/2" FLAT HEAD SCREWS (WW).
Step 2
Page 6 www.sauder.com 412373
(L)
Y(R)
Q2
R2
Y
1/2" FLAT HEAD SCREW
(4 used for the RAILS)
WW
Roller end Roller end

å Fasten four METAL BRACKETS (EE) to the LEG
FRAMES (Q2 and R2). Use four 1/2" PAN HEAD
SCREWS (VV).
Step 3
Page 7www.sauder.com412373
EE
EE
EE
EE
Q2
R2
1/2" PAN HEAD SCREW
(4 used for the METAL BRACKETS)
VV
(4 used)
Use this hole
Use this hole
Use this hole

å Fasten the CONNECT TUBE (E) to the MIDDLE PANEL (I).
Use two 1-3/16" MACHINE SCREWS (PP). Tighten with
the L-WRENCH (FF).
Step 4
Page 8 www.sauder.com 412373
I
E
FF
1-3/16" MACHINE SCREW
(2 used in this step)
PP

Step 5
Page 9www.sauder.com412373
S
I
F
å NOTE: You will need someone's help in this step.
å Fasten the CONNECT TUBE (E) on the MIDDLE PANEL (I) to
the UPPER CONNECT TUBE (S). Use two 1/2" PAN HEAD
SCREWS (VV).
å Fasten the CONNECT TUBE (E) on the MIDDLE PANEL (I) to
the BACK PANEL (F). Use two 1/2" PAN HEAD SCREWS (VV).
å Fasten the MIDDLE PANEL (I) to the BACK PANEL (F). Use
a 1" PAN HEAD SCREW (RR).
E
1/2" PAN HEAD SCREW
(4 used for the CONNECT TUBE)
VV
1" PAN HEAD SCREW
(1 used in this step)
RR
This hole should be
closer to this edge.
Roller end
Surface with holes
These holes
must be here.

å Fasten the UPPER CONNECT TUBE (S) to the LEFT LEG
FRAME (Q2). Use a 1/2" BOLT (TT). Tighten with the
L-WREN CH (FF).
å Turn two 1" BOLTS (QQ) into the LEFT LEG FRAME (Q2).
Then, push the BACK PANEL (F) onto the pin of the 1"
BOLT in the LEFT LEG FRAME.
Step 6
Page 10 www.sauder.com 412373
Q2
F
S
1/2" BOLT
(1 used in this step)
TT
FF
1" BOLT
(2 used in this step)
QQ

å Turn your unit onto its front edges.
å Fasten two METAL BRACKETS (EE) to the MIDDLE CONNECT
TUBE (T). Use two 1/2" PAN HEAD SCREWS (VV).
å Fasten the MIDDLE CONNECT TUBE (T) to the LEFT LEG
FRAME (Q2). Use a 1/2" BOLT (TT). Tighten with the
L-WREN CH (FF).
Step 7
Page 11www.sauder.com412373
EE
T
Q2
1/2" PAN HEAD SCREW
(2 used for the METAL BRACKETS)
VV
1/2" BOLT
(1 used in this step)
TT
These holes should be
closer to this edge.
FF

å Fasten the MIDDLE SHELF (B) to the LEFT LEG
FRAME (Q2). Use two 1/2" PAN HEAD SCREWS (VV)
through the METAL BRACKETS on the LEFT LEG FRAME
and into the MIDDLE SHELF.
å Fasten the MIDDLE SHELF (B) to the MIDDLE CONNECT
TUBE (T). Use two 1/2" PAN HEAD SCREWS (VV)
through the METAL BRACKETS on the MIDDLE
CONNECT TUBE and into the MIDDLE SHELF.
Step 8
Page 12 www.sauder.com 412373
B
Q2
T
These holes
must be here.
1/2" PAN HEAD SCREW
(4 used for the METAL BRACKETS)
VV

å Fasten two LONG DECORATIVE METALS (X) to the long
edges of the BACK SUPPORT PANEL (J) as shown. Use
four 1/2" PAN HEAD SCREWS (VV).
Step 9
Page 13www.sauder.com412373
X
X
J
1/2" PAN HEAD SCREW
(4 used in this step)
VV

å Drop a few beads of GLUE (KK) onto two WOOD
DOWELS (DD) and insert them into the holes in the edge
of the BACK PANEL (F) as shown in the lower diagram.
å Place a SHORT DECORATIVE METAL (W) over the
WOOD DOWELS (DD).
å Drop a few beads of GLUE (KK) into the two holes in the
short edge of the BACK SUPPORT PANEL (J). Push the
BACK SUPPORT PANEL onto the WOOD DOWELS. Wipe
away the excess glue with a damp cloth.
å Fasten the BACK PANEL (J) to the MIDDLE SHELF (B).
Use two 1" PAN HEAD SCREWS (RR).
Step 10
Page 14 www.sauder.com 412373
J
F
B
W
Inspect the parts thoroughly before
assembling. Disassembly of glued
parts is extremely dicult.
Caution
!
1" PAN HEAD SCREW
(2 used in this step)
RR
KK
DD

å Fasten six METAL BRACKETS (EE) to the CONNECT
TUBES (U and V) exactly as shown. Use six 1/2" PAN
HEAD SCREWS (VV).
Step 11
Page 15www.sauder.com412373
EE
U
V
EE
1/2" PAN HEAD SCREW
(6 used for the METAL BRACKETS)
VV

å Fasten the LOWER FRONT CONNECT TUBE (V) to
the LEFT LEG FRAME (Q2). Use two 1/2" BOLTS (TT).
Tighten with the L-WRENCH (FF).
Step 12
Page 16 www.sauder.com 412373
1/2" BOLT
(2 used in this step)
TT
FF
V
These holes should be
closer to this edge.
Now might be a
good time to refresh
your drink.
Q2
Surface with METAL BRACKETS

å Fasten the LOWER BACK CONNECT TUBE (U) to the
LEFT LEG FRAME (Q2). Use two 1/2" BOLTS (TT).
Tighten with the L-WRENCH (FF).
å Fasten the LOWER BACK CONNECT TUBE (U) and
SHORT DECORATIVE METAL (W) to the BACK
SUPPORT PANEL (J). Use two 2-15/16" PAN HEAD
SCREWS (MM) through the LOWER BACK CONNECT
TUBE, through the SHORT DECORATIVE METAL, and
into the BACK SUPPORT PANEL.
Step 13
Page 17www.sauder.com412373
Surface without METAL BRACKETS
Q2
FF
U
J
W
2-15/16" PAN HEAD SCREW
(2 used in this step)
MM
The opposite surface holes
should be closer to this edge.
1/2" BOLT
(2 used in this step)
TT

å Fasten four METAL BRACKETS (EE) to the BOTTOM
SHELF (C). Use four 1/2" PAN HEAD SCREWS (VV).
Step 14
Page 18 www.sauder.com 412373
C
EE
EE
1/2" PAN HEAD SCREW
(4 used for the METAL BRACKETS)
VV

å Fasten the BOTTOM SHELF (C) to the CONNECT
TUBES (U and V). Use six 1/2" PAN HEAD SCREWS (VV)
through the METAL BRACKETS on the CONNECT TUBES
and into the BOTTOM SHELF.
Step 15
Page 19www.sauder.com412373
Surface with holes
U
C
V
1/2" PAN HEAD SCREW
(6 used for the METAL BRACKETS)
VV

å Turn two 1" BOLTS (QQ) into the RIGHT LEG FRAME (R2).
Then, push the pin of the 1" BOLT into the BACK PANEL (F).
å Fasten the RIGHT LEG FRAME (R2) to the CONNECT
TUBES (S, T, U, and V). Use six 1/2" BOLTS (TT). Tighten
with the L-WRENCH (FF).
Step 16
Page 20 www.sauder.com 412373
S
R2
T
V
U
F
1/2" BOLT
(6 used in this step)
TT
FF
1" BOLT
(2 used in this step)
QQ