Jackson 436DL User manual

JACKSON TOOL • P. O. BOX 5701 • GREENVILLE, SC 29606
877-522-8995 or 864-721-4235 • FAX [phone] • www.jacksontoolinc.com
Model 436DL
Deluxe V-Head Pipe Stand
This manual is free of charge. All personnel who operate this Pipe Stand
should have a copy of this manual and read and understand its contents.
To obtain a copy, call, write to the address below, or visit our website.
Read and understand this material before operating
or servicing the Pipe Stand. Failure to understand how
to safely operate and service this unit may result in
property damage, serious injury or death.
Operating, Safety and Parts Manual
10/17

2
TABLE OF CONTENTS
Safety Alerts .............................................. 2
Safety Information ......................................... 3
Features.................................................. 4
Specifications ............................................. 4
Operating Instructions...................................... 5
Transporting Instructions ................................... 5
Exploded View and Parts List – 436DL ........................ 6
Optional Hold Down Device Operating Instructions ............7,8
Exploded View and Parts List – 436DL-200 ..................... 9
SAFETY ALERTS
Safety Alert
Symbol
THIS SAFETY SYMBOL is used to call your attention to instructions
that concern your personal safety. It means: ATTENTION! BE
AWARE! THIS IS AN IMPORTANT SAFETY INSTRUCTION!
Read, understand and follow these safety instructions. Failure to
follow these safety instructions may result in injury or death.
DANGER
WARNING
CAUTION
Immediate hazards which, if not avoided, WILL result in serious personal
injury or death.
Hazards or unsafe practices which, if not avoided, COULD result in serious
personal injury or death.
Hazards or unsafe practices which, if not avoided, COULD result in minor
personal injury or property damage.

ALWAYS place the Pipe Stand on a smooth, level, firm surface that will
support the weight of the load. NEVER use on dirt or gravel surface. Be sure
all feet of the Pipe Stand make contact with the floor.
ALWAYS be sure the pipe is properly placed onto the Pipe Stand. Improperly
loaded pipe can cause tipping of the Pipe Stand, falling pipe and serious
injury.
ALWAYS inspect the Pipe Stand before each use. Never use if any legs or
other part of the Pipe Stand is bent, deformed, broken or has been modified.
ALWAYS adjust the quick height adjustment tube prior to loading pipe onto
the stand.
NEVER exceed the maximum rated capacity of the Pipe Stand.
NEVER alter the Pipe Stand. Only use for its designed purpose.
NEVER drop pipe onto the Pipe Stand.
NEVER allow anyone under the pipe while it is supported by the
Pipe Stand.
ALWAYS use a minimum of 2 Pipe Stands to support the pipe.
NEVER load more than one pipe onto the Pipe Stand.
DO NOT release lock ring with a load on the stand.
DO NOT exceed recommended working height of stand.
NEVER raise the quick height adjustment tube past the sight hole.
ALWAYS carry the Pipe Stand by both the V-Head assembly and the base. This
will help prevent injury from an improperly secured assembly.
ALWAYS make sure the lock ring is properly placed on the lock ring retainer
and the roll pin is in place.
ONLY use Jackson Tool replacement parts on the Pipe Stand. Use of parts
not supplied by Jackson Tool WILL NOT work properly on the Pipe Stand
and could result in serious personal injury or death.
BE SURE the pipe rests in the center of the V-Head and that the pipe is level
as it sits on the pipe stands.
ALWAYS wear gloves and other safety equipment for your specific job when
using the Pipe Stand.
RETAIN SAFETY INFORMATION
3
IMPORTANT SAFETY INFORMATION
Follow ALL safety information provided by the manufacturer.
WARNING
DANGER
CAUTION
This manual should be read and understood by all personnel who operate or service this
Pipe Stand. Failure to understand how to safely operate and service this unit could result in
injury or death. This unit should only be operated or serviced by qualified personnel.
WARNING
DANGER
CAUTION
WARNING
DANGER
CAUTION
WARNING
DANGER
CAUTION
WARNING
DANGER
CAUTION
WARNING
DANGER
CAUTION
WARNING
DANGER
CAUTION
WARNING
DANGER
CAUTION
WARNING
DANGER
CAUTION
WARNING
DANGER
CAUTION
WARNING
DANGER
CAUTION
WARNING
DANGER
CAUTION
WARNING
DANGER
CAUTION
WARNING
DANGER
CAUTION
WARNING
DANGER
CAUTION
WARNING
DANGER
CAUTION
WARNING
DANGER
CAUTION
WARNING
DANGER
CAUTION

4
FEATURES
SPECIFICATIONS
Model No. 436DL
Pipe Size Capacity 1/2" to 12"
Max. Weight Capacity 2500 lbs. per Stand
Overall Dimensions L 24" W 201⁄2" H 32" (fully retracted)
Min. Stand Height 30"*
Max. Stand Height 51"*
Weight 21 lbs.
Retainer bracket
keeps V-head assembly
captured in the quick
height adjustment tube
12” diameter pipe capacity
Alignment hole
Sight hole
(To help avoid over
extension of quick height
adjustment tube)
Base legs made
from 1" square tubing
Height adjustment nut
Transport hole to safely
secure quick height adjustment tube
for transport
Lock ring retained with roll pin
2,500 lb. working
load capacity
Quick height adjustment
tube to help avoid hands
from being pinched
T-screw
Powder coat
finish
*See drawing in the features section above
NOTE: The minimum
stand height and
maximum stand
height measurements
are from the bottom of
the legs of the stand
to the bottom
of the “V.”
*Min. stand height 30"
*Max. stand height 51"

5
1. Inspect the Pipe Stand before each use. NEVER use if any legs or other part of the stand is bent,
deformed, broken or has been modified.
2. Place the Pipe Stand on a smooth, level, firm surface that will support the weight of the load. Be
sure all feet of the stand make contact with the floor.
3. With no load on the Pipe Stand, loosen the T-screw. Grasp the quick height adjustment tube and lift
to desired height. NOTE: DO NOT raise the quick height adjustment tube past the sight hole. If you
are not able to see the quick height adjustment tube in the sight hole, lower the quick height
adjustment tube until it completely fills the sight hole. Release the quick height adjustment tube and
ensure that the lock ring has engaged. This will help prevent the quick height adjustment tube from
lowering further. NOTE: ALWAYS
make sure the lock ring is properly
placed on the lock ring retainer and
the roll pin is in place. See Figure 5.
4. Securely tighten the T-screw.
5. Turn the height adjustment nut to
the desired height. For adjustment
purposes, leave approximately 2"
to 3" of thread showing under the
“V”. NOTE: use only hand pressure
to turn the height adjustment nut.
6. Place the pipe onto the pipe stands.
Be sure the pipe rests in the center
of the V-Head and that the pipe is
level as it sits on the pipe stands.
NOTE: After pipe is removed from the stands, lower the stands by loosening the T-Screw. Then
securely grasp the quick height adjustment tube and lift up on the tabbed end of the lock ring.
OPERATING INSTRUCTIONS
1. DO NOT move the stand(s) until the pipe has been removed.
2. Remove the pipe hold down device if it is being used.
3. Turn the height adjustment nut to fully lower the head assembly.
4. Loosen the T-screw.
5. Securely grasp the quick height adjustment tube and lift up on the tabbed end of the lock ring.
While continuing to lift the lock ring, COMPLETELY lower the quick height adjustment tube.
Place the alignment hole in line with the lock ring retainer.
6. To secure the stand for transport, tighten the T-screw through the transport hole in the quick
height adjustment tube until it tightens. Stand will then be ready for transport.
TRANSPORTING INSTRUCTIONS
CORRECT PLACEMENT OF LOCK RING INCORRECT PLACEMENT OF LOCK RING
Lock ring
retainer Lock ring
(Tabbed end)
Sight hole
T-screw
Figure 5
WARNING
ALWAYS support the pipe with a minimum of two (2) Pipe Stands. Place stands to properly support the pipe.
Pipe size, weight and length are some of the factors to consider when supporting pipe with the Pipe Stands.
WARNING
NEVER drop the pipe onto the pipe stands. NEVER exceed the maximum rated capacity of the pipe stands. To
avoid tipping, be sure the Pipe Stands are properly aligned, the pipe rests in the center of the V-Head and the
pipe is level as it sits on the pipe stands. Never allow anyone under the pipe while it is supported by the stands.

6
EXPLODED VIEW — 436DL DELUXE PIPE STAND
COMPONENTS LIST
ITEM# PART# QTY DESCRIPTION
1 436DL-121 1 Base
2 436DL-123 1 V-Head assembly
3 436-088 1 Lock ring
4 436DL-122 1 Quick height adjustment tube
5 2508-581 1 T-screw
6 436DL-103 1 Retainer bracket
7 436-112 2 Screw, button head cap – 1/4-20 ×1/2"
8 186-20 1 Roll pin – 3/16
PARTS LIST — 436DL DELUXE PIPE STAND
5
4
2
1
6
8
7
3

1. Place the hold down device on top of the pipe,
in line with the center of the pipe stand base
(See photo 1).
2. In order that you have the maximum amount of
adjustment travel, adjust the handle/nut so that the
nut is flush with the end of the acme screw. (See
photo 2.)
3. Pull the loose end of the chain and wrap once
around the acme threaded rod. Chain should
be under the V and above the height
adjustment nut (See photo 3.)
4. Continue the chain around the pipe and pull as
tight as possible. Insert chain link onto the
hook of the hold down bracket (See photo 4).
7
OPTIONAL HOLD DOWN DEVICE 436DL-200 OPERATING INSTRUCTIONS
DANGER
WARNING
CAUTION
Hold down device is only to secure pipe to the Pipe Stand.
DO NOT use for any other purpose.
Photo 1
Photo 2
nut acme
screw
Photo 3
Photo 4

8
OPTIONAL HOLD DOWN DEVICE #436 DL-200 OPERATING INSTRUCTIONS – CONTINUED
5. Turn hold down device handle/nut to tighten
chain. As you tighten the chain with the
handle/nut, check to ensure that the full length
of the chain tightens against the pipe.
(See photo 5).
NOTE: If the chain does not tighten before
you run out of adjustment, loosen the
handle/nut and place the next link of
the chain into the hook on the hold
down bracket. Be sure the hold down
bracket and chain are in line with the
V-head assembly to ensure the chain
remains tight. (See photos below).
Right Wrong
Photo 5

ITEM# PART# QTY DESCRIPTION
1 ...................636-7 ..................1................ Handle/Nut
2 .................636-858 ................1................ Hold Down Bracket
3 .............. 436DL-201 ..............1................ Acme Screw/Chain
Assembly
HOLD DOWN DEVICE #436DL – 200
EXPLODED VIEW AND PARTS LIST
9
1
2
3