Sauder Palladia 411864 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-23
Français pg 24-27
Español pg 28-31
Lot # 357575 11/25/13
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Panel TV Stand
Palladia Collection | 411864
Smart stand
for the idiot box.

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
WARNING
!
Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or
death. A TV that is too large for the available space might be accidentally pushed or bumped o the furniture, or subject to tip-over.
• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!
• This Sauder unit is designed for use with televisions weighing less than 95 pounds. Never use with a TV that weighs more.
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diagram.
• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)
• Never allow the sides of the TV to extend past the side edges of the TV support surface.
• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.
• Be sure to apply the warning label as instructed in the last assembly step. The label provides important safety related information.
3
4
5-23
24-27
28-31
32-34
35
Tip Shown Actual Size
95 lbs.
95 lbs.
18-7/8"
18-7/8"
47"
47"
411864 www.sauder.com/servicesPage 2
Tape Measure

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C RIGHT UPRIGHT (1)
D LEFT UPRIGHT (1)
E TOP (1)
F BOTTOM (1)
G BACK (1)
H DOOR (2)
I LARGE ADJUSTABLE SHELF (2)
J SMALL ADJUSTABLE SHELF (2)
K BASE (1)
L LOWER PLINTH (2)
M SIDE MOLDING (2)
N BOTTOM MOLDING (1)
O UPPER PLINTH (2)
P FRONT MOLDING (1)
Q RIGHT MOLDING (1)
R LEFT MOLDING (1)
S RIGHT END MOLDING (1)
T LEFT END MOLDING (1)
U RIGHT HINGE MOLDING (1)
V LEFT HINGE MOLDING (1)
W VALANCE (1)
X BRACE (1)
Y HALF DISK (2)
411864www.sauder.com/services Page 3
A
B
C
D
E
F
G
H
H
I
I
J
K
M
M
N
P
Q
R
S
T
U
V
W
X
L
L
Y
Y
O
O
J

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
411864 www.sauder.com/servicesPage 4
FELT DISC CARD - 1
II
TIE PLATE - 4
DD
METAL BRACKET - 14
CC
GOLD 1" MACHINE SCREW - 2
PP
BLACK 9/16" LARGE HEAD SCREW - 28
RR
BLACK 1-1/4" FLAT HEAD SCREW - 18
NN
BROWN 7/16" LARGE HEAD SCREW - 8
SS
BLACK 1-7/8" FLAT HEAD SCREW - 6
MM
ZTWIST-LOCK®FASTENER - 8
OO BROWN 1" FLAT HEAD SCREW - 10
RUBBER SLEEVE - 16
KK
METAL PIN - 20
JJ
SILVER 5/8" FLAT HEAD SCREW - 8
QQ
MOLDING
CONNECTOR - 2
GG
FF
HINGE SPACER - 4
EE HINGE - 4 KNOB - 2
HH
NAIL - 36
TT
HIDDEN CAM - 4
AA2 CAM DOWEL - 4 BB2
(Refer to the last step for proper location and application)
WARNING LABEL - 1
LL
WARNING
Never use this furniture with a TV that is too
large or too heavy. Severe injury or death
can occur.The TV and furniture will be
unstable and may tip.
-The TV must less than 95 lbs.
-The base of the TV must be able to sit
completely on this shelf.
-Refer to instruction book for complete
safety information.
Note: This is a permanent label. Do not try
to remove. Surface will be damaged.
02/ 02 269227

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push a SAUDER TWIST-LOCK®
FASTENER (Z) into the large holes in the ENDS (A and B).
Repeat this step for the BOTTOM (F)
411864www.sauder.com/services Page 5
(8 used)
Do not tighten the TWIST-LOCK® FASTENERS in this step.
Z
A
B

å Push four HIDDEN CAMS (AA2) into the
HINGE MOLDINGS (U and V).
Step 2
411864 www.sauder.com/servicesPage 6
Do not tighten the HIDDEN CAMS in this step.
Arrow
AA2
U
V
(4 used)
Hole
Arrow

å Tap two MOLDING CONNECTORS (GG) into the notches
in the MOLDINGS (P, Q, and R).
Step 3
411864www.sauder.com/services Page 7
Use your hammer to tap the MOLDING CONNECTOR (GG) into the notches in the MOLDINGS
Flat end
Flat end
PQ
R
GG GG

å Fasten the MOLDINGS (P, Q, and R) to the TOP (E). Use
eight BLACK 1-1/4" FLAT HEAD SCREWS (NN).
Step 4
411864 www.sauder.com/servicesPage 8
E
P
Q
R
BLACK 1-1/4" FLAT HEAD SCREW
(8 used in this step)
NN
Rounded edge
Surface
with holes

å Fasten the LEFT END (B) to the LEFT MOLDING (R) on
the TOP (E). Tighten two TWIST-LOCK® FASTENERS.
å Insert four METAL PINS (JJ) into the TOP (E).
å Push the UPRIGHTS (C and D) onto the METAL PINS (JJ)
in the TOP (E).
Step 5
411864www.sauder.com/services Page 9
How to use the SAUDER TWIST-LOCK®FASTENER
1. Insert the dowel end of the FASTENER into the
hole of the adjoining part.
NOTE: The dowel end of the FASTENER must
remain fully inserted in the hole of the adjoining
part while locking the FASTENER.
2. Tighten the FASTENER with a Phillips
screwdriver as tight as possible.
Dowel end
6-3/4"
7-5/8"
Finished edge
B
C
D
E
R
JJ
JJ
Surface with
6 holes
Surface with
12 holes
Surface with TWIST-LOCK®
FASTENERS
Rounded edge
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution

Step 6
å Fasten the BOTTOM (F) to the LEFT END (B). Tighten two
TWIST-LOCK® FASTENERS.
å Fasten the BOTTOM (F) to the UPRIGHTS (C and D). Use
four BLACK 1-7/8" FLAT HEAD SCREWS (MM).
å Fasten the RIGHT END (A) to the BOTTOM (F) and RIGHT
MOLDING (Q). Tighten four TWIST-LOCK® FASTENERS.
411864 www.sauder.com/servicesPage 10
Unfinished
surface
Surface without TWIST-LOCK®
FASTENERS
Q
A
B
C
D
F
These holes must be here.
BLACK 1-7/8" FLAT HEAD SCREW
(4 used in this step)
MM

Surface with
more holes.
Step 7
å Carefully set your unit onto its top.
å Fasten six METAL BRACKETS (CC) to the END
MOLDINGS (S and T). Use six BLACK 9/16" LARGE
HEAD SCREWS (RR).
å NOTE: Be sure the BRACKETS are even with the edges of
the END MOLDINGS.
å Fasten the END MOLDINGS (S and T) to the ENDS (A and B).
Use six BLACK 9/16" LARGE HEAD SCREWS (RR) through
the METAL BRACKETS and into the ENDS.
411864www.sauder.com/services Page 11
A
B
S
S
T
T
CC
CC
Surface without
METAL BRACKETS
Surface without
METAL BRACKETS
Finished edge
BLACK 9/16" LARGE HEAD SCREW
(12 used for the METAL BRACKETS)
RR

å Fasten the UPPER PLINTHS (O) to the END
MOLDINGS (S and T). Use two BLACK 1-1/4"
FLAT HEAD SCREWS (NN).
å Fasten the SIDE MOLDINGS (M) to the END
MOLDINGS (S and T). Use four BLACK 1-1/4" FLAT
HEAD SCREWS (NN).
å NOTE: There are no pre-drilled holes in the SIDE
MOLDINGS. The SCREWS will tighten into the groove.
Step 8
411864 www.sauder.com/servicesPage 12
M
M
T
S
Curved edge
BLACK 1-1/4" FLAT HEAD SCREW
(6 used in this step)
NN
O
O
The END MOLDINGS
will set in from the edge.

å Insert four CAM DOWELS (BB2) into the
END MOLDINGS (S and T).
å Then, insert the CAM DOWELS (BB2) in the END
MOLDINGS (S and T) into the HIDDEN CAMS in the
HINGE MOLDINGS (U and V). Tighten four HIDDEN CAMS.
Step 9
411864www.sauder.com/services Page 13
BB2
BB2
U
V
Finished edge
Finished edge
Surface with HIDDEN CAMS
Surface without
HIDDEN CAMS
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
T
S

å Fasten two METAL BRACKETS (CC) to the TOP (E) and
HINGE MOLDINGS (U and V). Use four BLACK 9/16"
LARGE HEAD SCREWS (RR).
å Fasten the HINGE MOLDINGS (U and V) to the BOTTOM (F).
Use two BLACK 1-7/8" FLAT HEAD SCREWS (MM).
Step 10
411864 www.sauder.com/servicesPage 14
E
F
V
CC
CC
U
BLACK 9/16" LARGE HEAD SCREW
(4 used for the METAL BRACKETS)
RR
BLACK 1-7/8" FLAT HEAD SCREW
(2 used in this step)
MM

å Fasten four TIE PLATES (DD) to the FRONT MOLDING (P).
Use four BROWN 7/16" LARGE HEAD SCREWS (SS).
å Fasten the VALANCE (W) to the TIE PLATES on the
FRONT MOLDING (P). Use four BROWN 7/16" LARGE
HEAD SCREWS (SS).
Step 11
411864www.sauder.com/services Page 15
P
W
DD
Wider edge
BROWN 7/16" LARGE HEAD SCREW
(8 used for the TIE PLATES)
SS
DD

å Fasten six METAL BRACKETS (CC) to the
BRACE (X). Use six BLACK 9/16" LARGE
HEAD SCREWS (RR).
å NOTE: Be sure the BRACKETS are even with
the edges of the BRACE.
å Fasten the BRACE (X) to the ENDS (A and B)
and BOTTOM (F). Use six BLACK 9/16" LARGE
HEAD SCREWS (RR) through the METAL
BRACKETS and into the ENDS and BOTTOM.
Step 12
411864 www.sauder.com/servicesPage 16
BLACK 9/16" LARGE HEAD SCREW
(12 used for the METAL BRACKETS)
RR
A
B
F
X
CC
CC
CC
X

å Fasten the BASE (K) and BOTTOM MOLDING (N) to the
BRACE (X). Use eight BROWN 1" FLAT HEAD SCREWS (OO).
Step 13
411864www.sauder.com/services Page 17
K
N
X
Be sure the holes are
closest to this long edge.
BROWN 1" FLAT HEAD SCREW
(8 used in this step)
OO

å Fasten the HALF DISKS (Y) to the LOWER PLINTHS (L).
Use two BROWN 1" FLAT HEAD SCREWS (OO).
å Fasten the LOWER PLINTHS (L) to the BRACE (X). Use
four BLACK 1-1/4" FLAT HEAD SCREWS (NN).
Step 14
411864 www.sauder.com/servicesPage 18
L
L
L
L
X
Y
Y
Y
The larger hole must be facing up.
BLACK 1-1/4" FLAT HEAD SCREW
(4 used in this step)
NN
BROWN 1" FLAT HEAD SCREW
(2 used for the HALF DISK)
OO
Flat edge
Flat edge
Flip the LOWER
PLINTHS (L) over.
Flip the LOWER
PLINTHS (L) over.
Y

å Carefully turn your unit over onto its front edges. Unfold
the BACK (G) and lay it over your unit.
å Line up the bottom edge of the BACK (G) with the
BOTTOM (F), then push on opposite corners of your unit
if needed to make it “square”.
å Fasten the BACK (G) to your unit using the NAILS (TT).
å NOTE: Be sure to tap NAILS into the holes that line up
over the UPRIGHTS (C and D).
å NOTE: Perforations have been provided for access
through the BACK. Carefully cut out the holes needed.
Step 15
411864www.sauder.com/services Page 19
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
Unfinished surface
NAIL
(36 used in this step)
TT
F
G
This perforation should be
closer to the BOTTOM (F).
The holes must line up over
the UPRIGHTS (C and D).

å Fasten four HINGE SPACERS (FF) and four HINGES (EE)
to the DOORS (H). Use eight SILVER 5/8" FLAT
HEAD SCREWS (QQ).
Step 16
411864 www.sauder.com/servicesPage 20
H
H
FF
FF
EE
EE
SILVER 5/8" FLAT HEAD SCREW
(8 used in this step)
QQ