Sauder Palladia 411864 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-23
Français pg 24-27
Español pg 28-31
Lot # 357575 11/25/13
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Panel TV Stand
Palladia Collection | 411864
Smart stand
for the idiot box.

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
WARNING
!
Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or
death. A TV that is too large for the available space might be accidentally pushed or bumped o the furniture, or subject to tip-over.
• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!
• This Sauder unit is designed for use with televisions weighing less than 95 pounds. Never use with a TV that weighs more.
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diagram.
• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)
• Never allow the sides of the TV to extend past the side edges of the TV support surface.
• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.
• Be sure to apply the warning label as instructed in the last assembly step. The label provides important safety related information.
3
4
5-23
24-27
28-31
32-34
35
Tip Shown Actual Size
95 lbs.
95 lbs.
18-7/8"
18-7/8"
47"
47"
411864 www.sauder.com/servicesPage 2
Tape Measure

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C RIGHT UPRIGHT (1)
D LEFT UPRIGHT (1)
E TOP (1)
F BOTTOM (1)
G BACK (1)
H DOOR (2)
I LARGE ADJUSTABLE SHELF (2)
J SMALL ADJUSTABLE SHELF (2)
K BASE (1)
L LOWER PLINTH (2)
M SIDE MOLDING (2)
N BOTTOM MOLDING (1)
O UPPER PLINTH (2)
P FRONT MOLDING (1)
Q RIGHT MOLDING (1)
R LEFT MOLDING (1)
S RIGHT END MOLDING (1)
T LEFT END MOLDING (1)
U RIGHT HINGE MOLDING (1)
V LEFT HINGE MOLDING (1)
W VALANCE (1)
X BRACE (1)
Y HALF DISK (2)
411864www.sauder.com/services Page 3
A
B
C
D
E
F
G
H
H
I
I
J
K
M
M
N
P
Q
R
S
T
U
V
W
X
L
L
Y
Y
O
O
J

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
411864 www.sauder.com/servicesPage 4
FELT DISC CARD - 1
II
TIE PLATE - 4
DD
METAL BRACKET - 14
CC
GOLD 1" MACHINE SCREW - 2
PP
BLACK 9/16" LARGE HEAD SCREW - 28
RR
BLACK 1-1/4" FLAT HEAD SCREW - 18
NN
BROWN 7/16" LARGE HEAD SCREW - 8
SS
BLACK 1-7/8" FLAT HEAD SCREW - 6
MM
ZTWIST-LOCK®FASTENER - 8
OO BROWN 1" FLAT HEAD SCREW - 10
RUBBER SLEEVE - 16
KK
METAL PIN - 20
JJ
SILVER 5/8" FLAT HEAD SCREW - 8
QQ
MOLDING
CONNECTOR - 2
GG
FF
HINGE SPACER - 4
EE HINGE - 4 KNOB - 2
HH
NAIL - 36
TT
HIDDEN CAM - 4
AA2 CAM DOWEL - 4 BB2
(Refer to the last step for proper location and application)
WARNING LABEL - 1
LL
WARNING
Never use this furniture with a TV that is too
large or too heavy. Severe injury or death
can occur.The TV and furniture will be
unstable and may tip.
-The TV must less than 95 lbs.
-The base of the TV must be able to sit
completely on this shelf.
-Refer to instruction book for complete
safety information.
Note: This is a permanent label. Do not try
to remove. Surface will be damaged.
02/ 02 269227

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push a SAUDER TWIST-LOCK®
FASTENER (Z) into the large holes in the ENDS (A and B).
Repeat this step for the BOTTOM (F)
411864www.sauder.com/services Page 5
(8 used)
Do not tighten the TWIST-LOCK® FASTENERS in this step.
Z
A
B

å Push four HIDDEN CAMS (AA2) into the
HINGE MOLDINGS (U and V).
Step 2
411864 www.sauder.com/servicesPage 6
Do not tighten the HIDDEN CAMS in this step.
Arrow
AA2
U
V
(4 used)
Hole
Arrow

å Tap two MOLDING CONNECTORS (GG) into the notches
in the MOLDINGS (P, Q, and R).
Step 3
411864www.sauder.com/services Page 7
Use your hammer to tap the MOLDING CONNECTOR (GG) into the notches in the MOLDINGS
Flat end
Flat end
PQ
R
GG GG

å Fasten the MOLDINGS (P, Q, and R) to the TOP (E). Use
eight BLACK 1-1/4" FLAT HEAD SCREWS (NN).
Step 4
411864 www.sauder.com/servicesPage 8
E
P
Q
R
BLACK 1-1/4" FLAT HEAD SCREW
(8 used in this step)
NN
Rounded edge
Surface
with holes

å Fasten the LEFT END (B) to the LEFT MOLDING (R) on
the TOP (E). Tighten two TWIST-LOCK® FASTENERS.
å Insert four METAL PINS (JJ) into the TOP (E).
å Push the UPRIGHTS (C and D) onto the METAL PINS (JJ)
in the TOP (E).
Step 5
411864www.sauder.com/services Page 9
How to use the SAUDER TWIST-LOCK®FASTENER
1. Insert the dowel end of the FASTENER into the
hole of the adjoining part.
NOTE: The dowel end of the FASTENER must
remain fully inserted in the hole of the adjoining
part while locking the FASTENER.
2. Tighten the FASTENER with a Phillips
screwdriver as tight as possible.
Dowel end
6-3/4"
7-5/8"
Finished edge
B
C
D
E
R
JJ
JJ
Surface with
6 holes
Surface with
12 holes
Surface with TWIST-LOCK®
FASTENERS
Rounded edge
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution

Step 6
å Fasten the BOTTOM (F) to the LEFT END (B). Tighten two
TWIST-LOCK® FASTENERS.
å Fasten the BOTTOM (F) to the UPRIGHTS (C and D). Use
four BLACK 1-7/8" FLAT HEAD SCREWS (MM).
å Fasten the RIGHT END (A) to the BOTTOM (F) and RIGHT
MOLDING (Q). Tighten four TWIST-LOCK® FASTENERS.
411864 www.sauder.com/servicesPage 10
Unfinished
surface
Surface without TWIST-LOCK®
FASTENERS
Q
A
B
C
D
F
These holes must be here.
BLACK 1-7/8" FLAT HEAD SCREW
(4 used in this step)
MM