ScaffoldMart UTLSCAFF4 Installation and operating manual

User Manual & Safety Guide
4’ Utility Scaffolding
MODEL: UTLSCAFF4
ONE YEAR
WARRANTY
Thoroughly read
this manual before
assembling or using
scaffolding unit. Failure
to do so can result in
injury or death.
Seriously... read it.
LB

Safety Guide
Read Instructions thoroughly before assemblage. Non-compliance with
guidelines may result in serious injury or death.
Do Not Over Encumber
This unit was designed for a maximum
capacity load of 500 lbs (227 kg)
Per decking unit: 250 lbs (113 kg)
Tool Shelf: 35 lbs (16 kg)
PRIOR TO USE
• Only use scaffold unit as intended while complying
with local, state, and national guidelines and
legislation.
• A competent person should manually inspect
scaffolding prior to each use, ensuring it is in good
working condition and that all parts are present and
properly assembled.
• Only use on level, hard, even surfaces. Avoid using
scaffold on surfaces that are soft, muddy, debris lled,
holey or otherwise obstructed.
• Refrain from using scaffolding if you are unwell, taking
medication, consuming alcohol, mind-altering drugs
or experiencing any other condition that may impair
your ability to work.
• Two platforms should be installed on frame structure
prior to use, both set level. Scaffold collapse is
possible if both platforms are not set level and could
result in injury or death.
• Casters must always be secured with span pins and
caster brakes must be locked before climbing or
standing on scaffolding.
• Do not use any scaffolding component that is
damaged or if parts are missing.
DURING USE
• Keep body centered inside structure of scaffold to
avoid tipping.
• Maintain a constant rm grip while climbing scaffold.
Always maintain three points of contact.
• Keep scaffold free of clutter and unnecessary
equipment to avoid tripping while in use.
• If any part of scaffolding unit becomes damaged
during use, it should be removed immediately from
the work area and replaced.
• Acids are corrosive and exposure diminishes the
integrity of scaffold unit. Do not expose to corrosive
materials.
• Remove or fasten all tools, material, or equipment
before moving scaffolding. Never move scaffold while
a person is on unit. Be careful when moving unit to
avoid tipping.
• This scaffold should be stored inside, out of the
elements and away from excessive heat or corrosive
materials. Rust and other forms of corrosion or
deterioration compromise the structural integrity
of the scaffold and should be avoided. Do not use
scaffold if structure is compromised in any way.
• Unit intended to hold a maximum of one person.
• A safe work platform to stand upon should be at least
18 inches wide.
• Remove all tools and materials before moving
scaffolding.
• Before using tool shelf, make sure hinges are fully
engaged.
DO NOTS
• Never use powered devices to propel this scaffold
unit.
• Never stack on loose materials, boxes, or any other
non-approved foundation.
• Never move scaffold with personnel on unit.
• Never load unit without caster brakes locked.
• Never use scaffold in windy conditions or during
inclement weather.
• Never use on uneven or soft surfaces.
• Never stand or sit on tool shelf. Max shelf
capacity 35 lb.
• Never use if any part of the scaffold unit is missing.
• Never modify the scaffolding in any way, doing so
voids its warranty.
• Never climb the outside of the unit.
Metal Conducts Electricity
Never use scaffolding unit in proximity
to live electrical circuits or power lines.

IMAGE PRODUCT NAME PART NUMBER
Anti-Slip Rings UTLSLIPRING
J Hook UTLHOOK
Tube Caps UTLCAP
Span Pin 381SPANPL
Caster Wheel and
Span Pin MF378-5RP
Spring Rivet 381SR
Tool Shelf &
Hinge Kit UTLSHELF
Assembly Instructions
Replacement Parts
1 Begin on level, rm, unobstructed surface.
Unpack box and lay out all the included parts.
2 With scaffold laid at on the ground, insert
casters into bottom of unit, securing with
included span pins. Lock the brakes on all four
wheels before proceeding.
3 Stand the scaffold unit up and spread its
ends away from one another, keeping them in
parallel. Unit will tip if ends are not in parallel.
4 With unit extended, place platforms at desired
heights. Make certain platforms are properly
seated and level, with their semi-circular cut-
outs snug against the horizontal supports.
5 Install upper handrail by rst fastening
it’s two ends to the center portion. Make
certain spring rivets are secure, then install
in the vertical tubes of the unit. Again, make
certain spring rivets secure all connections.
6 Install platform hooks. The top horizontal beam
is drilled with two holes, insert hooks through
these holes and secure with included nuts.
11
YEAR ONE YEAR WARRANTY
ScaffoldMart guarantees this product against any material
defect for a period of one year beginning at the time of purchase.
This warranty does not cover damages or injury due to
inappropriate or incorrect use, care or maintenance of your unit.
To order these
replacement parts,
contact our customer
service department.
Customer Service:
1 [phone]
[email protected]
scaffoldmart.com

Box Contents
List of Box Contents
A. Frame Structure ( 1 )
B. Handrail Assembly ( 1 )
C. Platforms ( 2 )
D. Caster Wheels ( 4 )
E. Span Pins ( 4 )
F. Hooks w/ Nuts ( 2 )
G. Spring Rivets ( 4 )
DE
A
B
C
FG