Scanstrut PTM-R1-S40 User manual

TAPERED RADAR MAST PTM-R1-S40
AND PTM-R2-S40
19-07-23 (Issue 1) Installation Instructions
For further installation
and warranty information
please visit:
www.scanstrut.com
USA
[phone]
[email protected]
UK & International
[phone]
[email protected]
X1 X1 X2
X6
Part List
X1X1 X1
X6
X12
X4
X4
X6
X12
X4
X6
X12 X4
X4
X6
X12X12
X4
X4
X3
X1
X1
X2
X4 X4
60080
M8 Nut
60065
M6 Washer
60065
M6 Washer
A4 M10 Washer
A4 M10 Hex Head bolt
suitable for install
60085
M8 Washer
65058
M5 Shoulder Washer
64004
M10 Shoulder washer
60060
M6 Nut
60060
M6 Nut
60702
M6 Nylon washer
60068
M6 Nut cover
19008
Base seal
610825
M8x25 CSK bolt
60510
M5x10mm Pan Head
10039
M100-200 plate
620260
M6x25mm Sockert head
60068
M6 Nut cover
610625
M6x25mm CSK bolt
60621
M6x20 Hex Head bolt
101817
Ø16 Grommet
101804
Ø23 Grommet
PTM-1-S40 only PTM-2-S40 only
101818
Tube cap
FLIR M100/200 riser kit
Parts not supplied
PTM-003863
Cover plate
PTM-003782
PTM Wing RH
PTM-003848
PTM Wing LH
PTM-R-S40
Taper mast
DPT-R-PLATE-02
Mounting plate
DPT-R-PLATE-01
Mounting plate

TAPERED RADAR MAST PTM-R1-S40
AND PTM-R2-S40
19-07-23 (Issue 1) Installation Instructions
PTM-003782
65085 x 4
PTM-003848
101818
DPT-R-PLATE-01
Or
DPT-R-PLATE-02
60510 x4
Apply thread lock to xing
60068
x6
60060
x6
60065
x12
60621
x6
61082 5 x4
101804 x3
101817 x2
PTM-003863
x2
64004
x4
60085 x4
60080 x4
64004
Tools Required
Pozi and at head
screwdriver Drill bit Ø10mm
Hole saw suitable for
cable routing
Spanner 13mm x 1
10mm x 2 No. 5 allen key
Riser kit only
Tools Required

TAPERED RADAR MAST PTM-R1-S40
AND PTM-R2-S40
19-07-23 (Issue 1) Installation Instructions
620260 x6
610625x6
60702 x6
60702 x6
60621 x6
60621 x6
60060 x6
60060 x6
60068 x6
FLIR M100/200 riser kit assembly
IMPORTANT
No liability is accepted for damage caused by incorrect instal-
lation.
The installation and assembly must be regularly inspected for
evidence of damage or loose parts.
Product has been designed specically for the mounting of
approved marine electronics under normal boating conditions.
IMPORTANT
Scanstrut déclinent toute responsabilité pour les dégats résult-
ant d’une installation incorrecte.
L’installation et l’assemblage doivent être inspectés régulière-
ment an de déceler des dégats ou des pièces désserrées
Ce produit a été spéciquement conçu pour le montage d’ap-
pareils d’électronique marine approuvés dans des conditions
de navigation normales.
WICHTIG
Für Schäden aufgrund unsachgemäßen Einbaus wird keine
Haftung übernommen.
Der Anbau und die Baueinheit müssen regelmäßig auf An-
zeichen von Schäden oder lockere Teile geprüft werden.
Dieses Produkt wurde spezisch für die Befestigung gene-
hmigter Elektronikgeräte für die Schifffahrt unter normalen
Bootsfahrtsbedingungen entwickelt.
IMPORTANTE
Si declina qualsiasi responsabilità per danni causati da un’in-
stallazione erronea.
L’installazione e il montaggio devono essere ispezionati con
regolarità per vericare la presenza di danni o di pezzi allentati.
Questo prodotto è stato studiato appositamente per il suppor-
to di apparecchiature elettroniche navali approvate in normali
condizioni di navigazione.
IMPORTANTE
No se aceptará ninguna responsabilidad por los daños causa-
dos por una instalación incorrecta.
La instalación y ensamblaje deberá inspeccionarse regular-
mente, comprobando cualquier evidencia de daños o piezas
aojadas.
Este producto ha sido especícamente diseñado para el mon-
taje de equipos electrónicos marinos aprobados bajo condi-
ciones normales de navegación.