Scanstrut SC-SL-01 User manual

SC-SL-01 03-01-2024 (Issue 1) Installation Instructions
For further installation
and warranty information
please visit:
www.scanstrut.com
USA
[phone]
[email protected]
Scanstrut Inc.
7 Pequot Park Road
Westbrook, CT
06498, USA
UK & International
[phone]
[email protected]
Scanstrut Ltd
Dart Business Park,
Clyst St. George, Exeter
EX3 0QH, UK
Waterproof Cable Routing
ø = + 1.5mm
4mm (0.16”)
Tip: freeze before drilling
-18°
Part List
Foam Seal DS30 Shell DS30 Bungs M4 x 10 Bolt
x1 x1 x2 x4
M8 x 16 Hex Tops M8 Nyloc Nuts M8 Nut Capsx6 x4 x4 x4
M8 Nylon Washers x4 x4 x4
M8 Nylon
Shoulder Washers
M8 x 25 Hex Tops
004765
60821
60818
x10
64015
101819
60080
60084
60857
6004972
60402
6004970
1/4”Stainless
Steel Washers
1/4”x 5/8” Cap
Head Screws
x4 x4
M10 x 25mm+
Hex Tops
M8 x 25mm+
Hex Tops
-MAKE NOTE ABOUT SELF TAPPING SCREWS SUPPLIED FOR WHEN
ON A POLE MOUNT AND NEEDS WATERPROOF ON DECK INSEAD (TAKE
CABLE SEAL OFF STARLINNK MOUNT)
- FOR WAREHOUSE INSTRUCTIONS MENTION ABOUT DURALAC FOR
FIXINGS TO STARLINK MOUNT TO PREVENT GALVANIC CORROSION. Only needed if moving
cable seal to deck.
Use the ø8.5mm bung supplied
for routing the Starlink cable.
For routing a number of cables.
> 600mm
(23.6”)
Parts Required
Option A Option B
Tools Required
ø8.5mm (21/64”)
Drill Bit
ø32mm (1 1/4”)
Hole Saw/Drill Bit
ø50-70mm (2”-2 3/4”)
Hole Saw
No.1 Pozi Drive
Screwdriver
Power Drill
13mm Spanner
3/16”Allen Key
Thread Lock
Option A Option B
Recommended Starlink Cable Length
1a
1b
Pass smaller connector through the cable seal
until the length is at least 600m (23.6”).

SC-SL-01 03-01-2024 (Issue 1) Installation Instructions
For further installation
and warranty information
please visit:
www.scanstrut.com
USA
[phone]
[email protected]
Scanstrut Inc.
7 Pequot Park Road
Westbrook, CT
06498, USA
UK & International
[phone]
[email protected]
Scanstrut Ltd
Dart Business Park,
Clyst St. George, Exeter
EX3 0QH, UK
Option A - Mounting to Deck:
4x M8 Fasteners
(Not Supplied)
4x 64015
4x 60402
101819
004765
ø32mm
(1 1/4”)
ø8.5mm
(21/64”)

SC-SL-01 03-01-2024 (Issue 1) Installation Instructions
For further installation
and warranty information
please visit:
www.scanstrut.com
USA
[phone]
[email protected]
Scanstrut Inc.
7 Pequot Park Road
Westbrook, CT
06498, USA
UK & International
[phone]
[email protected]
Scanstrut Ltd
Dart Business Park,
Clyst St. George, Exeter
EX3 0QH, UK
DPT-LB-02 ONLY
(DOES NOT FIT DPT-LB-01)
19070 (supllied with DPT)
For more information, see
installation instructions for DPT-R.
64004
(supllied with DPT)
19008
(supllied with DPT)
6x 60818
6x 64015
Optional
light bar
M10 Fasteners
(Not Supplied)
4x 60402
101819
ø32mm
(1 1/4”)
Forward
ø8.5mm
(21/64”)
Option B - Mounting to: • DPT-R
• DPT-R-COMP
• DPT-OA

SC-SL-01 03-01-2024 (Issue 1) Installation Instructions
For further installation
and warranty information
please visit:
www.scanstrut.com
USA
[phone]
[email protected]
Scanstrut Inc.
7 Pequot Park Road
Westbrook, CT
06498, USA
UK & International
[phone]
[email protected]
Scanstrut Ltd
Dart Business Park,
Clyst St. George, Exeter
EX3 0QH, UK
4x 60857
4x 60080
4x 60084
4x 60821
4x 64015
For more information,
see installation
instructions for SC100.
Recommended Cable Routing:
• SC103
• SC102
Option C - Mounting to:

SC-SL-01 03-01-2024 (Issue 1) Installation Instructions
For further installation
and warranty information
please visit:
www.scanstrut.com
USA
[phone]
[email protected]
Scanstrut Inc.
7 Pequot Park Road
Westbrook, CT
06498, USA
UK & International
[phone]
[email protected]
Scanstrut Ltd
Dart Business Park,
Clyst St. George, Exeter
EX3 0QH, UK
4x 64015
4x 6004972
4x 6004970
1
2

SC-SL-01 03-01-2024 (Issue 1) Installation Instructions
For further installation
and warranty information
please visit:
www.scanstrut.com
USA
[phone]
[email protected]
Scanstrut Inc.
7 Pequot Park Road
Westbrook, CT
06498, USA
UK & International
[phone]
[email protected]
Scanstrut Ltd
Dart Business Park,
Clyst St. George, Exeter
EX3 0QH, UK
IMPORTANT
Wedge Mounts are only compatible with marine electronics devices as stated in the latest Scanstrut Product Guide – subject to
change without prior notice.
Use of the Wedge Mounts with unapproved products, or overloading, invalidates any product warranty.
Scanstrut does not supply fastenings to x this product to the chosen surface. Please choose suitable fastenings for this purpose.
No liability is accepted for damage caused by incorrect installation.
The installation and assembly must be regularly inspected for evidence of damage or loose parts.
Product has been designed specically for the mounting of approved marine electronics under normal boating conditions.
IMPORTANT
Supports de cale sont uniquement compatibles avec les appareils d’électronique marine repris dans le dernier Guide Produits
Scanstrut – sujet à Modica-tion sans préavis.
L’usage des Supports de cale avec des produits non validés, ou la surcharge de ces supports, annulent toute garantie.
Scanstrut ne fourni pas les xations pour sécuriser ce produit à la surface de choix. Veuillez utiliser des xations appropriées pour
cette opération.
Scanstrut déclinent toute responsabilité pour les dégats résultant d’une installation incorrecte.
L’installation et l’assemblage doivent être inspectés régulièrement an de déceler des dégats ou des pièces désserrées
Ce produit a été spéciquement conçu pour le montage d’appareils d’électronique marine approuvés dans des conditions de
navigation normales.
WICHTIG
Keilhalterungen sind nur mit Elektronikgeräten für die Schifffahrt kompatibel, wie in der aktuellen Scanstrut Produktübersicht er-
wähnt. Änderungen ohne vorherige Ankündigung vorbehalten.
Durch die Verwendung mit nicht genehmigten Produkten bzw. durch Überlastung wird jegliche Garantie ungültig.
Befestigungsteile für die Montage dieses Produkts auf der gewählten Oberäche. Bitte wählen Sie geeignete Befestigungsteile für
diesen Zweck.
Für Schäden aufgrund unsachgemäßen Einbaus wird keine Haftung übernommen.
Der Anbau und die Baueinheit müssen regelmäßig auf Anzeichen von Schäden oder lockere Teile geprüft werden.
Dieses Produkt wurde spezisch für die Befestigung genehmigter Elektronikgeräte für die Schifffahrt unter normalen Boots-
fahrtsbedingungen entwickelt.
IMPORTANTE
Supporti a cuneo sono compatibili solo con apparecchiature elettroniche navali come indicato nella più recente Guida ai Prodotti
Scanstrut – fatte salve eventuali modiche senza preavviso.
L’uso di supporti a cuneo con prodotti non approvati, o un loro sovraccarico, invalida qualsiasi garanzia.
Scanstrut non fornisce dispositivi per ssare questo prodotto alla supercie prescelta. Scegliere dispositivi di ssaggio adatti a
questo scopo.
Si declina qualsiasi responsabilità per danni causati da un’installazione erronea.
L’installazione e il montaggio devono essere ispezionati con regolarità per vericare la presenza di danni o di pezzi allentati.
Questo prodotto è stato studiato appositamente per il supporto di apparecchiature elettroniche navali approvate in normali
condizioni di navigazione.
IMPORTANTE
Montajes de cuña son compatibles únicamente con equipos electrónicos marinos según se establece en la última Guía de
Productos Scanstrut– sujeto a cambios sin previo aviso.
El uso de los montajes de cuñacon productos no aprobados, o bajo exceso de carga, invalidará cualquier garantía.
Scanstrut no suministra anclajes para jar el producto sobre la supercie elegida. Escoja el sistema de jación más adecua-
do para este propósito.
No se aceptará ninguna responsabilidad por los daños causados por una instalación incorrecta.
La instalación y ensamblaje deberá inspeccionarse regularmente, comprobando cualquier evidencia de daños o piezas
aojadas.
Este producto ha sido especícamente diseñado para el montaje de equipos electrónicos marinos aprobados bajo condi-
ciones normales de navegación.