ScatterBox HDM312 User manual

HDMI 1 in 2 out SPLITTER with IR extender XHDM312
Email: suppo[email protected] Last Revised 01/06/2018
Parts Supplied
HDMI 1 in 2 out Splitter
5vDC Power Supply
IR Adaptor
IR Transmitter
IR Receiver
1. Power 5v DC 2. HDMI Input 5. Dipswitches 6. IR TX
3. HDMI output 2 4. HDMI output 1 7. USB Interface 8. HDMI LED 1
9. HDMI LED 2 10. RESET
11. Power Indicator
Features
This HDMI splitter will distribute two HDMI signals from a source device such as a DVR, DVD player,
Satellite Receiver, Set Top Box, DV Camera, A/V Receiver or other HDMI device to HDTVs or HDMI
flat panel display monitor.
1. Fully compliant with HDMI 1.4 specification.
2. Supports CEC. Consumer Electronics Control (CEC) is a feature of HDMI designed to allow
users to command and control up to 15 devices connected through HDMI by using one CEC
remote controller.
3. Incorporates built in IR extender function.
4. Blue-Ray DVD 24/50/60fs.
5. Audio formats DTS-HD / Dolby-true HD/ DTS / Dolby-AC3 / DSD.
6. Extends transmission distance and improves transmission signal. Using an HDM150 can extend
distance further. An HDM150 can be used prior to and after the HDM312. See test results below.
RESOLUTION
INPUT TO
INPUT TO
OUTPUT
TOTAL RUN
1080P
HDM312
15 metres
-
-
15 metres
30 metres
1080P
HDM150
15 metres
HDM312
15 metres
15 metres
45 metres
4K
HDM312
10 metres
-
-
15 metres
25 metres
4K
HDM150
10 metres
HDM312
15 metres
15 metres
40 metres
7. Supports EDID - Extended Display Identification Data (EDID) is a data structure provided by a
digital display to describe its video capabilities to a video source (e.g. PC graphics card , set-top
box etc). It enables a modern PC to know what kinds of monitors are connected to it.
HDM312 1 IN 2 OUT HDMI SPLITTER
This is a 4K 3D HDMI splitter and provides HD
output streams for 480i/p, 576i/p, 720i/p, 1080i/p and
3840 x 2160 @ 25/30Hz.
Using dipswitches you can produce 2 x 1080, 2 x 4K,
Copy input to 2 outputs or Combination if one output
is 4K second output will be 1080p.
Additionally the HDM312 supports an IR extender.
This can be used to control a monitor IR remote.
1
2
3
4
5
6
7
8
9
10
11

HDMI 1 in 2 out SPLITTER with IR extender XHDM312
Email: suppo[email protected] Last Revised 01/06/2018
Installation
1. Connect an HDMI cable from an HDMI source (e.g MEGA DVR, DVD Player etc.) to the HDM312
Input. The maximum cable run from the HDMI source is 15m for a 1080P signal or 10m for 4K. If the
distance of the cable run needs to be longer, you can use an *HDM150 HDMI extender prior to and if
necessary following the HDM312. See test results on previous page.
2. Connect an HDMI lead to the Output 1 and 2 on the HDM312 with maximum run of 15 metres and
connect the 2 monitors.
3. Set EDID dipswitch settings. 1111 = 1080P (set if both outputs are 1080P)
0000 = 4K (set if both outputs are 4K)
0011 = EDID Copy (set if both outputs copy input)
1100 = EDID Combination (output 1 is 4K, output 2 is 1080P)
4. Connect the 5vDC 2A regulated power supply to the 2.1mm power jack socket.
5. Using the IR remote facility - optional
If you want to use the IR remote for example controlling the MEGA DVR, see below:
a) Ensure that the adaptor switch is correctly set to IR or CEC. IR is for controlling a standard IR
remote but a CEC IR remote can control multiple devices with the one control. Only one HDMI channel
can use the IR remote.
b) Connect the IR Adaptor into the HDMI connection on the monitor.
c) Connect the HDMI cable from the DVR HDMI output into the IR Adaptor detailed in b).
d) Connect the IR Receiver mini jack plug into the IR Adaptor and remove the cover from the sticky
pad and fix the IR Receiver to the monitor case so that it can be seen by the DVR IR remote controller.
e) Connect the IR Transmitter mini jack plug to the jack socket on the HDM312 and remove the cover
from the sticky pad and fix the IR Receiver to something facing the DVR IR sensor.
f) Now you can use the DVR IR Remote controller by pointing at the IR Receiver attached to the
monitor and you can control the DVR.
* HDM150 Extender can be purchased to increase cable run to and from the HDM312 splitter.
Technical Specification for HDM312
HDMI Input
1
HDMI Version
HDMI 1.4
Cable Standard
28AWG HDMI 1.4
HDMI Output
2
Bandwidth
Up to 340 MHz
Power Consumption
1.5 watts max / 120mA
Input Video
0.5 –1.0 v p~p
Signal Speed
Up to 10.2 Gbps
Power Supply
5v 1 amp
Input DDC Signal
5v p~p (TTL)
Input cable Length
15m 1080P / 10m 4K
Net Weight / Size
110g / 100x48x25mm
HDMI connectors
19 pin HDMI 1A –‘A’
Output cable Length
15m 1080P / 15m 4K
Operating Temperature
0°C ~ 70°C
Single Link Range
3840 x 2160
Input/Output Extender
HDM150 15m x 2
Special Features
IR control / EDID
All specifications are approximate. Kovert.com reserves the right to change
any product specification or features without notice. Whilst every effort is
made to ensure that these instructions are complete and accurate,
kovert.com cannot be held responsible in any way for any losses, no matter
how they arise, from errors or omissions in these instructions, or the
performance or non-performance of the camera or other equipment that
these instructions refer to.