Schacht SPOOL RACK User manual

SPOOL RACK
Assembly InstructIons
PARTS
2 – bases
2 – uprights
1 – bottom brace
1 – center pivot
1 – top brace
HARDWARE
2 – 3 1/2" truss-head machine screws
4 – 1 ¾" at head machine screws
2 – 2 ½" truss head machine screws
8 – barrel nuts
10 – metal rods
10 – 1" Phillips head screws
15 100 100 0 67 60 36 0 30 0 100 10
12 30 80 24 10 67 72 10 84 4 0 28
0 50 80 10 60 25 0 50 22 70 94 5
Find out more at schachtspindle.com
Schacht Spindle Company 6101 Ben Place Boulder, CO 80301
p. 303.442.3212 f. 303.447.9273
© 2013 Schacht Spindle Company, Inc. 01.13
top brace
bottom brace
base
base
upright
upright
center pivot
barrel
nuts
barrel nuts
barrel
nut
barrel nut
barrel nut
barrel nut
3 1/2"
screw
2 1/2"
screw
2 1/2"
screw
3 1/2"
screw
1 3/4"
screws 1 3/4"
screws
holes for
1" Phillips
screws
steel bars
ASSEMBLY
1. Assemble the bases to the uprights
using (2) 3 1/2" truss-head machine
screws and (2) barrel nuts as shown
in the diagram.
2. Assemble the bottom brace to the
bases using (2) 2 l/2" long machine
screws and (2) barrel nuts. Make sure
the notch in the center of the brace
faces up.
3. Install the ten metal rods into the
holes in the center pivot so that the
bars extend evenly on each side. You
can rub the rods with bar soap to help
them slide in. When all the rods are
installed, secure each rod with one of
the 1" Phillips screws.
4. Place the center pivot with metal
rods in position into the hole and
notch in the bottom brace.
5. Assemble the top brace to the
uprights with the 1 3/4" long machine
screws and barrel nuts. Make sure
the center pivot hole faces down.
6. To turn the center pivot, simply lift
and turn. The center pivot will lock it-
self in place when in its normal use. •

SPOOL RACK
Assembly InstructIons
PARTS
2 – bases
2 – uprights
1 – bottom brace
1 – center pivot
1 – top brace
HARDWARE
2 – 3 1/2" truss-head machine screws
4 – 1 ¾" at head machine screws
2 – 2 ½" truss head machine screws
8 – barrel nuts
10 – metal rods
10 – 1" Phillips head screws
15 100 100 0 67 60 36 0 30 0 100 10
12 30 80 24 10 67 72 10 84 4 0 28
0 50 80 10 60 25 0 50 22 70 94 5
Find out more at schachtspindle.com
Schacht Spindle Company 6101 Ben Place Boulder, CO 80301
p. 303.442.3212 f. 303.447.9273
© 2013 Schacht Spindle Company, Inc. 01.13
ASSEMBLY
1. Assemble the bases to the uprights
using (2) 3 1/2" truss-head machine
screws and (2) barrel nuts as shown
in the diagram.
2. Assemble the bottom brace to the
bases using (2) 2 l/2" long machine
screws and (2) barrel nuts. Make sure
the notch in the center of the brace
faces up.
3. Install the ten metal rods into the
holes in the center pivot so that the
bars extend evenly on each side. You
can rub the rods with bar soap to help
them slide in. When all the rods are
installed, secure each rod with one of
the 1" Phillips screws.
4. Place the center pivot with metal
rods in position into the hole and
notch in the bottom brace.
5. Assemble the top brace to the
uprights with the 1 3/4" long machine
screws and barrel nuts. Make sure
the center pivot hole faces down.
6. To turn the center pivot, simply lift
and turn. The center pivot will lock it-
self in place when in its normal use. •
top brace
bottom brace
base
base
upright
upright
center pivot
barrel
nuts
barrel nuts
barrel
nut
barrel nut
barrel nut
barrel nut
3 1/2"
screw
2 1/2"
screw
2 1/2"
screw
3 1/2"
screw
1 3/4"
screws 1 3/4"
screws
holes for
1" Phillips
screws
steel bars