Schiller Grounds Care STEINER 75-70585B Owner's manual

OP / PARTS MANUAL
MAN 4167929 Rev. A 05-2012
MODEL:
75-70585B
ROTARY SWEEPER 54”RS350

CALIFORNIA
Proposition 65 Warning
Diesel engine exhaust and some of
itsconstituentsareknowntotheState
of California to cause cancer, birth
defects and other reproductive harm.
Californie Proposition 65 Avertisse-
ment
Les échappements des moteurs diesel et
certains de leurs composés sont reconnus
par l’Etat de Californie pour être cancéri-
gènes,provoquerdesdéfautscongénitaux
etd’autresdangersenmatièredereproduc-
tion.
ADVERTENCIA
AVERTISSEMENT
WARNING
The engine exhaust from this product
containschemicalsknown to theState
of California to cause cancer, birth
defects or other reproductive harm.
California Advertencia
de la Proposicion 65
El estado de California hace saber
que los gases de escape de los mo-
tores diesel y algunos de sus com-
ponentes producen cáncer, defectos
de nacimiento y otros daños en el
proceso de reproducción humana.
L’
é mission du moteur de ce mat é riel
contient des produits chimiques que
l’Etat de Californie consid è re ê tre
canc é rig è nes,provoquerdes d é fauts
cong é nitaux et d’autres dangers en
mati è re de reproduction.
El estado de California hace saber
que los gases de escape de este
producto contienen productos quÍmi-
cos que producen cáncer, defectos
de nacimiento y otros daños en el
proceso de reproducción humana.
CALIFORNIA
Proposition 65 Warning
Battery posts, terminals, wiring
insulation, and related accessories
contain lead and lead compounds,
chemicals known to the State of
California to cause cancer and birth
defects or other reproductive harm.
WASH HANDS AFTER HANDLING.

3
ROTARY
SWEEPER
IMPORTANT MESSAGE
Thank you for purchasing this Schiller Grounds Care, Inc.product. You have purchased a world class product,
one of the best designed and built anywhere.
This product comes with an Owner/Operator's Manual. The useful life and good service you receive from this
product depends to a large extent on how well you read and understand this manual. Treat this product properly
and adjust it as instructed, and it will give you many years of reliable service.
See a Steiner dealer for any service or parts needed. Schiller Grounds Care, Inc.service ensures that you
continue to receive the best results possible from Schiller Grounds Care, Inc.products. You can trust Schiller
Grounds Care, Inc.replacement parts because they are manufactured with the same high precision and quality
as the original parts.
Schiller Grounds Care, Inc.designs and builds its equipment to serve many years in a safe and productive man-
ner. For longest life, use this product only as directed in the manual, keep it in good repair and follow safety
warnings and instructions. You'll always be glad you did.
Schiller Grounds Care, Inc.
One Bob Cat Lane
Johnson Creek, WI 53038-0469
05-2012
TABLE OF CONTENTS FIGURES PAGE
DESCRIPTION / SPECIFICATIONS................................................................................................................4
SAFETY........................................................................................................................................................5, 6
ASSEMBLY / INSTALLATION INSTRUCTIONS ..............................................................................................7
OPERATION.....................................................................................................................................................8
SERVICE....................................................................................................................................................9, 10
PARTS SECTION...........................................................................................................................................11
BROOM PARTS.................................................. FIGURE 1...................................................................12, 13
HITCH PARTS.....................................................FIGURE 2...................................................................14, 15
GEARBOX........................................................... FIGURE 3...................................................................16, 17
CASTER WHEELS.............................................. FIGURE 4.........................................................................18
BELT CHART.......................................................FIGURE 5.........................................................................19

4
ROTARY
SWEEPER
DESCRIPTION / SPECIFICATIONS
SPECIFICATIONS
Working Width.........................................................................................................54"
Overall Height..........................................................................................................18"
Overall Width...........................................................................................................61"
Overall Length.........................................................................................................44"
Right and Left Angle................................................................................................30oHydraulically Controlled
Speed of Broom at 3200 Engine RPM ....................................................................300 RPM
Ground Clearance in Raised Position .....................................................................10" (on Model 420)
Weight .....................................................................................................................170 lbs
DESCRIPTION
Clear away leaves and debris on pathways, parking lots, sidewalks, and driveways with this 54 inch
wide rotary sweeper. Hardwearing nylon broom, driven by a bevel gearbox from the tractor PTO, has
hydraulically controlled angling for left and right hand operation. Flotation springs (on older models) or
caster wheels (on newer models) reduce ground pressure on the broom for longer life.

5
ROTARY
SWEEPER
SAFETY
NOTICE !!!
Unauthorized modications may present extreme
safety hazards to operators and bystanders and
could also result in product damage.
Schiller Grounds Care, Inc. strongly warns against,
rejects and disclaims any modications, add-on
accessories or product alterations that are not
designed,developed,testedandapprovedbySchiller
Grounds Care, Inc.Engineering Department. Any
Schiller Grounds Care, Inc.product that is altered,
modied or changed in any manner not specically
authorized after original manufacture–including the
additionof“after-market”accessoriesorcomponent
parts not specically approved by CGC, Inc.–will
result in the Schiller Grounds Care, Inc.Warranty
being voided.
Any and all liability for personal injury and/or
property damage caused by any unauthorized
modications, add-on accessories or products not
approved by Schiller Grounds Care, Inc.will be
considered the responsibility of the individual(s) or
company designing and/or making such changes.
Schiller Grounds Care, Inc.will vigorously pursue
full indemnification and costs from any party
responsibleforsuchunauthorizedpost-manufacture
modications and/or accessories should personal
injury and/or property damage result.
This symbol means:
ATTENTION!
BECOME ALERT!
Your safety and the safety of others is involved.
Signal word denitions:
The signal words below are used to identify levels
of hazard seriousness. These words appear in this
manualandonthesafetylabelsattachedtoSchiller
Grounds Care, Inc.machines. For your safety and
thesafetyof others,readand followtheinformation
given with these signal words and/or the symbol
shown above.
DANGER indicates an imminently hazardous
situationwhich,if not avoided, WILL result in death
or serious injury.
WARNING indicates a potentially hazardous
situation which, if not avoided, COULD result in
death or serious injury.
CAUTIONindicatesapotentiallyhazardoussituation
which,ifnotavoided,MAY resultinminorormoderate
injury. It may also be used to alert against unsafe
practices or property damage.
CAUTION used without the safety alert symbol
indicates a potentially hazardous situation which, if
not avoided, MAY result in property damage.
MODEL NUMBER: This number appears on
sales literature, technical manuals and price lists.
SERIAL NUMBER: This number appears only
on your mower. It contains the model number
followed consecutively by the serial number.
Use this number when ordering parts or seeking
warranty information.

6
ROTARY
SWEEPER
1. Read and understand the Owner’s Manual before attempting to operate this machine.
2. Operate all controls from the operator’s seat. NO RIDERS.
3. Keep all shields in place and safety switches adjusted properly.
4. Do not leave equipment unattended. STOP the engine and remove the key.
5. Do not allow minors or the inexperienced to operate this machine.
6. Keep people and pets a safe distance away from machine using power driven attachments. Injury could
result from ying debris.
GENERAL SAFETY
OPERATING SAFETY
1. Stop engine to make repairs or adjustments. Do
not attempt to work on unit or attachments with
engine running.
2. Before leaving operator's seat:
 • Disengage PTO drive.
 • Set PARK brake.
 • Stop engine.
SAFETY

7
ROTARY
SWEEPER
ASSEMBLY INSTRUCTIONS
MODEL RS350 ROTARY SWEEPER
 • Remove broom from the shipping crate. Remove shipping bracket.
 • Remove the bottom belt shield from the hitch frame. Remove hose clamp from top of hitch frame.
 • Loosen 3/8 locking nuts on square head set screws. Turn setscrews in. These setscrews are used
to level the broom and must be adjusted after the sweeper is mounted on the power unit. Install hitch
frame to sweeper by inserting stud into the swivel ball in the center front of the hitch frame. Attach the
rear swivel ball to the hitch frame using the 3/8 X 1 ange bolts & nuts previously removed from the
shipping bracket.
 • Install belt and idler spring as shown in Photo 1.
 • Reinstall bottom belt shield.
 • Remove drive pulley shield and install the proper drive belt for the power unit. (See Photo 1) Replace
shield.
SEE BELT CHART PAGE 17 FOR PROPER BELT
• On sweeper install drive belt over left hitch arm and move tractor into position until the quick hitch can
be latched.
• Stop engine and install drive belt.
• Connect cylinder hoses to the auxiliary outlets. Extend the cylinder completely. Fasten hoses to hitch
frame with clamp as shown in Photo 2. Be certain that hoses are not stretched tight with the cylinder
fully extended. Keep hoses away from drive pulley.
• Adjust pivot stops to limit “tilt” of broom. EXTREME CARE MUST BE TAKEN TO LEVEL THE
BROOM AFTER IT ISATTACHED TO THE POWER UNIT! FAILURE TO LEVEL THE BROOM WILL
RESULT IN UNEVEN BROOM WEAR. (See page 9 Adjustments.)
• Choose power angle for right, left, or straight ahead position.
• With the sweeper mounted on the tractor, set the height adjustment by moving the 1/4" spacers on
the caster wheel frame.
Photo 2 - Hose Clamp and RoutingPhoto 1 - Drive Belt Installation

8
ROTARY
SWEEPER
OPERATION
OPERATING INSTRUCTIONS
1. Mount rotary sweeper according to instructions on page 7.
2. Raise sweeper to clear ground surface.
3. Adjust sweeper angle to the right, left or straight ahead position using the auxiliary hydraulic control
lever.
4. Engage PTO and set engine speed.
5. Lower sweeper by placing lift in FLOAT position. Check “FLOAT” pattern as described on page 7.
6. Move forward slowly.
7. Do not allow broom to bounce. This causes excessive broom wear. Adjustment of the oat can avoid
bounce.
8. Check the leveling of the broom each time the broom is used. The broom should contact the surface
equally the entire length of the broom. (See page 9 for leveling adjustment.)
Observe all Safety Decals.
Keep all Shields in Place.
Before leaving tractor, move Forward - Reverse control to neutral position, disengage PTO, set
parking brake and stop engine.
BE ALERT FOR OBJECTS IN THE PATH OF THE SWEEPER. POWER DRIVEN BROOM MAY
THROW OBJECTS CAUSING DAMAGE TO PROPERTY OR INJURY TO BYSTANDERS.

9
ROTARY
SWEEPER
SERVICE
MAINTENANCE
DAILY (10 HOUR) MAINTENANCE:
1. Check for signs of loose bolts etc.
•Replace or tighten.
2. Check oil level in gearbox.
 • Use #90 oil - 1/2 full
3. Remove cap plug and check chain.
Chain should not run dry.
 • Lube with roller chain lube or #30 oil.
ANNUAL (100 HOUR) MAINTENANCE:
1. In addition to daily maintenance:
 • Grease all bearings.
2. Remove chain shield and inspect.
 • Lube and adjust chain.
3. Storage
•Clean entire machine and support on
blocks to keep broom off the oor. Weight on
the broom bristles will distort the shape of the
broom
ADJUSTMENTS
Leveling adjustment:
Leveling the broom is accomplished by tilting the
mounting plate in relation to the hitch frame.
There are two square head set screws with
locking nuts which need to be adjusted to level
the broom. Loosen the locking nuts and adjust
the set screws so that the broom touches the
surface equally the entire length of the broom.
Depending on the power unit, this adjustment
may vary from side to side, so adjust it for the
position which is most used. Example: If you use
the broom angled to the right most of the time,
adjust the leveling with the broom angled in that
position. NOTE: For best results and longer
broom life...level the broom in the straight ahead
position and then alternate broom use in both
angle positions.
Drive chain adjustment:
The broom bearing is mounted in slotted holes in
the main frame and can be adjusted forward to
tighten the chain. Remove the chain shield.
Loosen the bearing mounting bolts and tighten
the adjuster nut until the chain is tight. Retighten
bearing bolts and replace the chain shield.
Float adjustment:
Adjust oat setting in the following steps:
A. Take unit to an area of loose stones or dirt.
B. Engage PTO to rotate broom and drop to
“FLOAT” position.
C. Raise the broom and note the test pattern
on the ground. The test pattern should
be 1-1/2" to 2" wide. A wider pattern will
result in excessive broom wear and power
consumption.
D. Adjust spring tension by choosing the proper
chain link on Models 420, 430, 440 and 425.
Adjust traction booster on Model 220, 230
and 525 to provide the proper otation.
The gauge wheels allow the sweeper to follow the
contour of the surface. The height is adjustable in
1/4" increments by moving the spacers on the
caster wheel frame. The correct height adjustment
is when the broom just touches the surface and
provides a “clean sweep”. Excessive broom wear
and power requirements may result from settings
which are too low.

10
ROTARY
SWEEPER
SERVICE
BROOM DRIVE BELT REPLACEMENT
1. Remove the drive pulley shield and the bottom
belt shield from the hitch frame.
2. Install the new belt and idler spring as shown in
Photo 3.
3. Reinstall the bottom belt shield and the drive
pulley shield.
Photo 3

PARTS
SECTION

12
ROTARY
SWEEPER
BROOM PARTS
FIGURE 1
2
10
38
4241 40
39
32
330
33
34
19
20
10
21
1817
16
15
5
10
14
13
12
38
11
22
23
10
24
18
25
26
18
27
28
29 36
37
35 8
9
2
7
6
5
4
3
1
31

13
ROTARY
SWEEPER
ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY
BROOM PARTS
FIGURE 1
1 4165138 SHIELD-TOP 1
2 00-092 DECAL-KEEP HNDS & FT 2
3 64139-08 BOLT-5/16-18X3/4 WLF 6
4 80-039 BROOM (15" X 54") 1
5 4138878 2-BOLT FLANGE BRG 2
6 62-097.17 FRAME, ROTARY SWEEPER 1
7 4165140 SHIELD-DRIVE SHAFT 1
8 64139-04 BOLT-WLF 1/4-20X3/4 2
9 04-015 INSERT-1/4-20 .260 GRIP 2
10 64141-4 NUT-WLF 3/8-16 6
11 64123-50 BOLT-HEX 3/8-16X1 2
12 64139-18 BLT-WLF 3/8-16X1-1/4 1
13 42-037.7 CHAIN TIGHTENER 1
14 64229-03 LOCKNUT-NYLON 3/8-16 1
15 82-078 SPROCKET 1
16 64164-10 1/4X1/4X1-1/4 MACH KEY 1
17 56-RC40-40 #40 ROLLER CHAIN 40" 1
81-056 CONNECTOR LINK, #40 1
81-076 #40 HALF LINK 1
18 64164-11 KEY-3/16X3/16X1-1/4 SQ 3
19 4165151 SHIELD, CHAIN 1
20 64141-2 NUT-WLF 1/4-20 4
21 83-H401012 SPROCKET, H4010 X 3/4 1
22 64123-98 BLT-HEX 1/4-20X2-1/2 4
23 55-FB23012 FLANGE BEARING 2 BOLT 1
24 80-040 SHAFT, 3/4 X 24-3/4 1
25 87-020 COUPLER, CHJP4 X 3/4 2
26 87-021 INSERT, COUPLING 1
27 87-209 GEARBOX 1
28 29-038 PIPE NIPPLE, 1/8 NPT X 2 1
29 24-031 PIPE CAP, 1/8 1
30 60-464.17 COVER, BEARING 1
31 4158620 DECAL-STEINER 1
32 64141-6 NUT, 5/16-18 2
33 00-093 DECAL-READ MANUAL 1
34 06-010 PLUG 1
35 64163-04 25/64X5/8X16GA WASHER 4
36 64006-02 LCKWSHR-HEL 5/16 4
37 64123-68 BOLT-HEX 5/16-18X1 4
38 64139-24 BLT-WLF 3/8-16 X 1 3
39 04-016 INSERT-5/16-18 .312 GRIP 4
40 64163-61 WSHR .81X.406X16GA 1
41 64-775.7 GEARBOX SHIELD BRKT 1
42 64139-13 BLT-WLF 5/16-18X1/2 1

14
ROTARY
SWEEPER
HITCH PARTS
FIGURE 2
59
55
5
6
29
56
55
5535
5
527
53
52
51
48
48
8
54
50
42
37
36
38
41
39
43
40
39 57
5
45 44
46 44
8
47 34
33
15 32
31
30 60
31
32
58 28
12
25 24
5
26
8
20
22 21
15 15
19
13
10 18
17
9
9
16 15
14
34
7
8
2
1
2
1
OPTIONAL
49
KIT 70-026
23
58
11
12
11
61
61

15
ROTARY
SWEEPER
ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY
HITCH PARTS
FIGURE 2
1 41-012 SPRING 2
2 56-018-07 CHAIN-7 LINKS 2
3 64-585.7 FLOAT SPRING BRKT 1
4 64139-21 BLT-WLF 3/8-16X3/4 2
5 64141-4 NUT-WLF 3/8-16 6
6 64163-02 WSR-.321/.328X.593/.608X11 2
7 99-K02 BOLT, FLANGE 5/16-18 X 1 2
8 64141-6 NUT, 5/16-18 5
70-026 FLOAT SPRING KIT 1
(INCLUDES ITEMS 1-8 & 60 - 62)
9 25-2103-6-6 FITTING-90 DEG. 2
10 20-218 HOSE, 1/4 X 48 100R1 1
11 25-0103-4-6 FITTING 2
12 23-004 MALE QUICK COUPLER 2
13 20-020 HOSE 1
14 64123-67 BLT-HEX 3/8-16X2 1
15 64229-03 LOCKNUT-NYLON 3/8-16 6
16 23-005 CYLINDER 1
* 21-13909X SEAL KIT 1
17 02-CP0612 COTTER PIN, 3/16 X 1-1/2 1
18 64163-64 WSHR 1.015X1.500X14 1
19 85-SC16 SET COLLAR 1
20 62-620.17 PIVOT PLATE 1
21 42-038.7 CLAMP, HOLD DOWN 1
22 42-039.7 CLAMP, HOLD DOWN 1
23 4116761 DECAL-USA 1
24 62-622.17 REAR PIVOT 1
25 90-1018 BOLT,5/8-11 X 2-1/4 NC 1
26 64025-21 NUT-HEX 5/8-11 1
27 85-SS10 SET SCREW, 3/8-16 X 1-1/2 2
28 4165155 HITCH FRAME 1
29 64123-16 BLT-HEX 3/8-16X1-1/4 1
30 48228-1A CLIP-CABLE INSULATED 1
31 64025-19 HEX, NUT 1/2-13 2
32 64006-05 LOCKWSHR-HELICAL 1/2 2
33 64139-24 BLT-WLF 3/8-16 X 1 2
34 41-020 SPRING 1
35 40-242.7 IDLER ARM 1
36 64164-11 KEY-3/16X3/16X1-1/4 SQ 1
37 83-BS8012 PULLEY 1
38 81-A087 BELT-A87 1
39 99-B12 SPACER 3
40 83-029 IDLER 1
41 83-012 PULLEY, IDLER 1
42 64123-235 BOLT, 1/2-13 x 1.3/4 1
43 64123-87 BOLT-HEX 3/8-16X1-3/4 1
44 64163-67 WASHER-.516X1X12GA 2
45 64123-31 BOLT-1/2-13X3 HEX 1
46 83-026 PULLEY, 2GR IDLER 1
47 60-452.17 SHIELD, DRIVE PULLEY 1
48 64-479 SPCR-PIVOT PLATE SHIELD 2
49 64163-29 WASHER 6
50 64123-104 BLT-HEX 5/16-18X2-3/4 2
51 60-453.17 SHIELD-BELT 1
52 SEE BELT CHART PAGE 17
53 64006-04 LOCKWSHR-HELICAL 5/8 1
54 64123-56 BLT-HEX 5/16-18X2 1
55 64163-61 WSHR .81X.406X16GA 3
56 64163-16 WASHER-41/64X1, 3/8X12 1
57 64123-50 BOLT-HEX 3/8-16X1 1
58 64229-02 LOCKNUT-NYLON 5/16-18 3
59 00-025 DECAL 1
60 64123-54 BLT-HEX 5/16-18 X 3/4 1
61 4167863-01 45° COUPLER 2
* NOT ILLUSTRATED

16
ROTARY
SWEEPER
GEARBOX
FIGURE 3

17
ROTARY
SWEEPER
ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY
GEARBOX
FIGURE 3
1 87-CM003582 HOUSING HALF 1
2 87-CM153437 BALL BEARING 3
3 87-CM301374 SEAL 2
4 87-CM226423 THRU SHAFT 1
5 87-CM108068 INTEGRAL SHAFT & PIN 1
(LEFT HAND)
6 87-CM153429 BALL BEARING 1
7 87-CM620013 RETAINING RING 1
8 87-CM640110 EXPANSION PLUG 1
9 87-CM108514 GEAR 1
(RIGHT HAND)
10 87-CM412320 ALLEN HD CAP SCREW 6
11 87-CM410506 LOCKWASHER 6
12 87-CM410001 PIPE PLUG-SOLID 2
13 87-CM800573 I.D. TAG 1
14 87-CM802876 I.D. TAG COVER 1
15 87-CM410068 PIPE PLUG-SOLID 1
16 87-CM003756 OUSING HALF 1
17 * 87-CM800326 GEAR LUBE, IN OZ. 5
* NOT ILLUSTRATED

18
ROTARY
SWEEPER
ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY
CASTER WHEELS
FIGURE 4
1 62-097.17 FRAME, ROTARY SWEEPER 1
2 03-017 CLIP, 5/16" 2
3 6112057 SPACER ENGINE PULLEY 20
4 35027N GREASE FITNG-1/4-28 90 2
5 64141-4 NUT-WLF 3/8-16 4
6 62-809.7 FRAME, CASTER SWIVEL 2
7 64123-171 BOLT-HEX 3/8-16X3-1/2 2
8 62-882.7 YOKE, CASTER W/A 2
9 64123-286 BOLT, 1/2 UNC x 4.1/2 2
10 50-104 AXLE, CASTER WHEEL 2
11 53-181 WHEEL, 6.25 X 3.00 2
12 64141-13 NUT WLF 1/2-13 2
13 64163-84 WSHR-1.015 X 1.75 X.125 2
14 64139-24 BLT-WLF 3/8-16 X 1 2

19
ROTARY
SWEEPER
MODEL 220 230 230 Diesel 235 410 415 420 430
425 525 UM428
Tractor PTO Belt 81-A034 W/O El Clutch
81-B033 W/El Clutch 81-B033 81-B033 416534781-B039 81-B039 81-A038 SN: 1001-2999
81-B039 SN:3000-5000 81-B039
81-B042 W/O El Clutch
81-B040 W/El Clutch 81-B04281-B029
MR, MW, MD, MX.
Rotary mowers 81-A040 81-A040 81-B041 81-B041 81-A040 81-A040 81-A040 81-A040
81-B04181-B041 81-B040
BM425 Boom MowerN/AN/A N/AN/A N/AN/A 81-A040 81-A040
81-B04181-B041 N/A
MC444 Tree Farm Mower RC466 Rough Cut Mower81-A042 W/O El Clutch
81-A040 W/El Clutch 81-A040 81-B041 81-B041 N/AN/A 81-A040 81-A040
81-B04181-B041 81-B040
RM674 & 684
Reel Mowers 81-A045 W/O El Clutch
81-A043 W/El Clutch 81-A043 81-B043 81-B043 N/AN/A 81-A043 81-A043
81-B044 W/O El Clutch
81-B042 W/El Clutch 81-B04381-B042
CS312 Chipper Shredder N/AN/A N/AN/A N/AN/A 81-B041 81-B041
81-B04181-B041 81-B040
GN10KW Generator81-B050 81-B050 81-B050 81-B050 81-B050 81-B050 81-B050 81-B050
81-B05081-B050 81-B050
LD300 Loader N/AN/A N/AN/A N/AN/A 81-A026 81-A026
N/AN/A N/A
PB100 & PB200 Power Blower 81-A042 W/O El Clutch
81-A040 W/El Clutch 81-A040 81-B041 81-B041 81-A040 81-A040 81-A040 81-A040
81-B041 W/O El Clutch 81-B04181-B040
PR348 Power Box Rake 81-A045 W/O El Clutch
81-A043 W/El Clutch 81-A043 81-B043 81-B043 N/AN/A 81-A043
81-B044 W/O El Clutch
81-B042 W/El Clutch 81-B04381-B043
RS350 small Rotary Sweeper 81-A042 W/O El Clutch
81-A040 W/El Clutch 81-A040 81-B040 81-B040 81-A040 81-A040 81-A040 81-A040
81-B041 W/O El Clutch
81-B040 W/El Clutch 81-B04081-B040
RS454 large Rotary Sweeper 81-A048 W/O El Clutch
81-A046 W/El Clutch 81-A046 81-B046 81-B046 81-A046 81-A046 81-A046 81-A046
81-B046 81-B04681-B044
SB348 Snowblower
SN:1001-1713 81-A055 W/O El Clutch
81-A053 W/El Clutch 81-A053 81-B054 81-B054 81-A053 81-A053 81-A053 81-A053
81-B054 W/O El Clutch
81-B053 W/El Clutch 81-B05481-B053
SB348 Snowblower
SN:1714-7570665**** 81-A053 W/O El Clutch
81-A051 W/El Clutch 81-A051 81-B051 81-B051 81-A051 81-A051 81-A051 81-A051
81-B053 W/O El Clutch
81-B051 W/El Clutch 81-B05181-B051
SB448 Snowblower 4165834 4165850 4165850 4165834 4165834 4165834 105803
SB454 Snowblower 4165834 4165850 4165850 4165834 4165834 4165834 105803
SC101 Stump Cutter N/AN/A N/AN/A 81-A043 81-A043 81-A043 81-A043
81-B045 W/O El Clutch
81-B043 W/El Clutch 81-B0424 81-B042
TH300 Trencher N/AN/A N/AN/A N/AN/A 81-B050 81-B050
81-B05181-B051 81-B050
TL348 Tiller 81-A042 W/O El Clutch
81-A040 W/El Clutch 81-A040 81-B041 81-B041 81-A040 81-A040 81-A040 81-A040
81-B041 W/O El Clutch
81-B040 W/El Clutch 81-B04181-B040
VA242 Vertical AugerN/AN/A N/AN/A N/AN/A 81-A027 81-A027
N/A N/A N/A
STEINER BELT CHART
81-B039 81-A040 81-A040 81-A040 81-A043 81-B041 81-B050 81-A040 81-A040 81-A046 81-A051
105803 105803
81-A043 81-B050 81-A040
N/AN/A N/AN/A N/AN/A 81-A040 81-A040
81-B041 81-B041N/A
81-A040
N/A
81-A053
440
BELT CHART
FIGURE 5

SCHILLER GROUNDS CARE, INC.
ONE BOB-CAT LANE
P.O. BOX 469
JOHNSON CREEK, WI 53038
920-699-2000
www.schillergc.com ©Schiller Grounds Care, Inc. 2010