Schweigen EV-6UCQ User manual

www.schweigen.com.auRevision V2_161219
RANGEHOOD & INSTALLATION GUIDE
EV-6UCQ
EV-9UCQ

Page 2
Index
1. Before Installation 3
Important Information 3
2. Maintenance & Service 4
Led Bulb Replacement 5
Electrical Cord 5
For Users 5
3. Description 6
Rangehood Contents 6
Operation 6
Cutout Size 6
4. Installation 7
Rangehood Size Vs Cooktop Size 7
Overhead Cabinet Rangehood Installation Position 7
Recommended Installation Height For Induction Cooktop 8
Mounting Points 9
Overview 10
5. Condensation Information 11
6. Troubleshooting 12
7. Service 13
8. Specications 14
Dimensions 14
Technical Specications 14
9. Disclaimer 15

Page 3
1. Before Installation
Important
• Please read this section thoroughly before attempting to install or operate the rangehood. Inspect
your product upon receipt. Any damage or defects MUST be reported within 48 hours, or no claim
will be recognised.
• Before installing the electrical connections, you should:
–Verify that the indicated electrical data coincide with the voltage values and frequency of the
electrical circuit in the house where the rangehood is to be installed;
–Check that the premises has electrical protection against short circuits and electrocution, pursuant
to the applicable legislation;
–Always switch o the current using the double-pole switch before maintenance and turn the power
on again for normal use only when the operation has been completed.
• DO NOT INSTALL THIS APPLIANCE IF YOU FIND IT DAMAGED.
• If this product is installed damaged, neither the supplier, nor the retailer, will be responsible for the
costs associated with the repair, replacement, removal or re-installation of the appliances.
• Please read the entire instructions before installing the rangehood, always switch power o prior to
installation. All electrical work must be done by a registered electrician in accordance with local and
national electrical codes as applicable. For your safety, this product must be earthed.
• The power socket must be accessible and enable the end user to isolate the rangehood from the
power for the purpose of internal cleaning or maintenance.
• Check the contents of the packaging, check all electrical functions of the canopy before installation.
Canopy is heavy. Please ensure adequate care when installing to prevent personal injury.
• A power outlet should be within reach of the power cord exit from the rangehood.
• The canopy hood is not intended for use by persons (including children) with reduced physical, sensory
or metal capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• There must be adequate ventilation of the room when the rangehood is used at the same time as
appliances burning gas or other fuels.
• There is a re risk if cleaning is not carried out in accordance with the instructions. You must read the
details concerning the method and frequency of cleaning.
• Do not ambé under the rangehood. This will void the warranty.
• Exhaust air must not be discharged into an existing ue which is used for exhausting fumes from
appliances burning gas or other fuels.
• The minimum distance between the hob surface and the lowest part of the rangehood is 650mm. This
distance shall be at least 650mm, if the rangehood is installed over a gas hob. If the instructions for the
gas hob specify a greater distance, this has to be taken into account.
• Attention should be given to ensure that any applicable regulations concerning the discharge of
exhaust air is fullled. Even a partial obstruction will restrict the eciency of the rangehood.
• Stainless steel is very easily damaged during installation if abraded or knocked by tools. Protect the
rangehood with the cardboard box or plastic bag during installation.

Page 4
2. Maintenance & Service
• CAUTION: Accessible parts may become hot when used with cooking appliances.
• We recommend this appliance be installed and repaired by a qualied technician.
• It is dangerous to modify any part of this appliance. Modication of any kind, will immediately void the
warranty.
• The manufacturer declines all responsibility in case of failure to adopt proper safety measures.
• Please consult local laws and regulations and install in accordance.
• Use an electrical connector with earth that is correct for your location.
• Check that the voltage in your area corresponds to the appliance as indicated on the rating label.
• This appliance must be connected to an electricity supply with a ground connection.
• Check that the installation and electrical connections are made by a qualied technician and that the
indicated instructions and local regulations in force are met, using materials that are compliant with the
applicable legislation.
• The company will not be responsible for installations executed by non-qualied persons and
installations that fail to heed the applicable legislation on electrical safety (with regard to both modes
and materials).
• The electrical technical data can be found inside the rangehood, after removing the grease lters.
• The exible power cable supplied is already connected internally and emerges from the rangehood
near the air outlet tube.
Maintenance and Service
• Always switch o and disconnect power before cleaning.
• The rangehood surface should be cleaned with soft cloth and non-corrosive detergent. Wash with
warm soapy water and a soft sponge. Never use abrasive detergent, scouring pads, steel wool or
solvents on any part of this appliance, Always make sure to dry the appliance after cleaning and never
leave wet, as this will cause irreparable damage.
• Clean the interior of the rangehood with a damp cloth and a neutral detergent or denatured alcohol.
• For better results, you can use high quality cleaning and protection products (e.g. Steel Kleen) to clean
rangehood.
• Do not leave the rangehood surface wet after cleaning.
• Particular care must be taken with the aluminium lters which must be periodically cleaned (at least
every month, this will vary depending on frequency of cooking and type of foods cooked). Remove
the grease lters and wash them either by hand using hot soapy water or in the dishwasher using
mild detergent. Do not scrub. Note - some discolouration of the frame may occur when washing in the
dishwasher Caution: Never use abrasive or oil based liquid cleaners.
• If the grease lters are very dirty, the motor will extract only a small quantity of air, which reduces
its eciency. The grease deposits that build up on the lter are highly ammable and COULD EASILY
CATCH FIRE. The manufacturer is exonerated from all responsibility in the event of re due to poor
maintenance of the grease lters.
• Important: Never attempt to repair this appliance by yourself. Always refer to a qualied Service
Technician. Remember to always switch o the electricity and unplug the connection before
conducting maintenance or cleaning.

Page 5
2. Maintenance & Service
LED Bulb Replacement
• Switch o the power to the canopy hood and allow the bulb to cool.
• Remove the bulb by turning it by hand in an anti clockwise direction
• Care must be taken to avoid the bulb falling onto the hob top
• Replace the bulb by inserting it into the socket and hand turning
in a clockwise direction
Electrical Cord
Ensure the supply cord is not exposed to heat, chemicals or sharp objects. If the supply cord is damaged,
it must be replaced by the manufacturer, service agent or a similarly qualied person in order to avoid
a hazard.
For Users
• This product is designed for household use and should not be used outside or for commercial
applications. After use, always ensure that all controls are in the “OFF” position. When frying with
a gas ame, take particular care not to allow the oil or grease in the pan to catch re. (Flambé)
• Do not leave the frying pan or fryer unattended, as the oil could overheat and catch re.
• Never ambé any foods beneath the rangehood. The ames could cause a re.
• Before carrying out any operation inside the rangehood, unplug the appliance from the electrical
mains.
• Respect the cleaning frequencies and intervals for changing the lters, as otherwise the accumulated
grease could cause a re or damage the product.
• Changes made to the steel surface will render the warranty invalid.
499
280
223
462
146
50
27
283
20
41
Max425 Min305
600
78.5
174
B
A
D
C
Ø4
A,B,C,D=
520
500
19
10
10
2
10
462±2
305
283
223±2
248
50
Ø
130±2
28
80
B
C
D
A
A
B
C
D
1
2
12 3 45
5

Page 6
3. Description
Rangehood Contents
1. Power to external motor system
2. Male Plug (Main Power 240V)
3. Single 200mm Outlet
4. Reducer – only for Hiow & Isodrive 650 motors
5. Filter
6. Light
Note: Filter and light quantity may vary from
model to model.
1
23
4
5
6
(60cm – 572mm approx.) (90cm – 872mm approx.)
267mm approx.
Note: Please make sure that all plastic protection on the rangehood and lters are removed before use.
Note: Dimensions may be subject to change.
Operation
This undermount is equipped with an ON/OFF switch. When the “ON” position is selected the unit
will run at maximum. When the “OFF” position is selected the rangehood will turn o.
Fan
1 2 3
“I” is the ON position and “O” is the OFF position.
Light
123
“I” is the ON position and “O” is the OFF position.
Cutout Size
Please use this as a guide only when designing your cabinet. Alternatively, present the rangehood
to your cabinet maker so that they may take their own measurements and check that the rangehood
ts in the cabinet correctly.

Page 7
4. Installation
Rangehood Size vs Cooktop Size
In addition to the size, the height of the rangehood above the cooktop is important to obtain
the best performance.
INADEQUATE
Rangehood smaller than
cooking zone
ADEQUATE
Rangehood same size as
cooking zone
OPTIMAL
Rangehood larger than
cooking zone
Overhead cabinet Rangehood Installation position
It is important to consider the benchtop and overhead cabinetry depth before installing the rangehood.
The information below is to be used as a guide only, drawings are not to scale and do not account
for all circumstances.
The cooktop is centrally installed in the benchtop in the diagrams below.
GOOD
600mm 600mm 600mm
400mm
Side View Side View
BETTER
450mm
BEST
500mm
When the overhead cabinetry is
constructed and installed deeper
than standard, ensure the rangehood
is installed as close to the front
as possible. This will increase the
rangehood extraction results as there
is a greater coverage of the cooktop
surface area.
Side View

Page 8
4. Installation
Mounting Instructions
It is STRONGLY RECOMMENDED that the rangehood be installed centrally over the cooktop.
This will greatly improve its performance.
Minimum height from the hob top surface to the underside face of the rangehood:
• 650mm electric cooktop
• 650mm gas cooktop
Any installation above 800mm will compromise the extraction performance.
Note: If the instructions for the gas cooktop specify a greater distance, this must be taken into account.
*IMPORTANT: If the user decides to install the
rangehood at a distance of less than minimum
height above the cooking surface, Schweigen
declines responsibility for damages suered
by the rangehood due to excess heat or damage
to objects, people and others caused directly
or indirectly by a malfunction, breakage or re.
Recommended Installation Height for Induction Cooktop
To help avoid condensation, particular to cooking with an induction cooktop, Schweigen recommends
a height of 700mm. Refer to page xx for further information.
Measurements are from the top of the trivets
to the lowest part of the rangehood, including
the button controls.
*Important: Please check all State and Federal Laws
in relation to the minimum–maximum heights,
regulations concerning the expelling of air and
install your rangehood in accordance with local
laws and regulations.

Page 9
4. Installation
MOUNTING POINTS
The diagrams below are a guide for all mounting points.
FRONT VIEW
TOP VIEW
BOTTOM VIEW
SIDE VIEW SIDE VIEW
FRONT VIEW
TOP VIEW
BOTTOM VIEW
SIDE VIEW SIDE VIEW
Bottom View
Front View Side View
Mounting point A and
B need to be tighted
with slightly angled
screws to pull the
rangehood up tight
to the cabinet.
These support screws insert from
the bottom of the rangehood.
These support screws insert from
the inside of the cabinet.
A B
Wall Cabinet
FRONT VIEW
TOP VIEW
BOTTOM VIEW
SIDE VIEW SIDE VIEW
Front
FRONT VIEW
TOP VIEW
BOTTOM VIEW
SIDE VIEW SIDE VIEW

Page 10
4. Installation
Overview
1
2
3
4
56
7
8
9
1. XDrive-600 Motor
2. Roof Seal Kit (Dektite)*
3. Support Straps*
4. Attach Flexi Duct to Bell-
Mouth Adaptor using duct
tape and cable tie. DO NOT
rip the ducting.
5. Motor Power Lead (Male Plug)
6. Rangehood to Motor Lead
(Female Plug)
7. Main Power Lead (Male Plug)
8. Flexi Ducting must be pulled
taut. DO NOT crush or kink
the ducting. Keep ducting
secured in place.
9. Connect exi ducting to the
outlet on rangehood using
duct tape or cable tie. Please
DO NOT rip the ducting.
*NOTE: The motor system does not include a roof seal kit, support straps, duct tape and cable ties.
There is a separate Motor Installation Guide in the Motor Box.
Flexi Ducting
IMPORTANT: For the motor to operate eciently, do not crush or kink the exi ducting, as it will reduce air
ow and may cause noise to occur through the system. Ducting needs to be kept taut at all times.
NOTE: For more information, please refer
to motor installation guide.

Page 11
5. Condensation Information
Cooking with Induction Cooktops
Cooking with an induction or similar cooktop, may produce condensation on the rangehood.
Unlike basic electric or gas cooking, induction cooktops heat food and liquid instantly, which in turn,
produces vapours rapidly. Because of this rapid process, the rangehood lters do not have enough
time to warm, which increases the chance of condensation forming.
There are many variables that may contribute to condensation forming, some of which include but
are not limited to:
• Variance in climate – geographical location
• Position of your home & kitchen – morning/afternoon sun
• Installation distance from cooktop to the rangehood
• Speed of food & liquid heating
• Angle of ducting – Sshweigen ‘S’ bend preferred
• Filter size - larger canopy preferred
• Quality of pots or cookware you are using – high quality recommended
How to reduce the possibility of condensation forming:
• Ensure the rangehood is installed by a qualied professional, carefully following the installation guide
• Turn on the rangehood 5-10 minutes prior to cooking, and leave on for 5-10 minutes after cooking;
this helps clear remaining vapours from the ue.
• Start the cooking process at a low-to-medium setting and allow time for the rangehood to warm up.
• Clean lters regularly.
• Ensure constant airow in the cooking zone; this helps optimise the rate of extraction.
• Follow all induction cooktop manufacturer advice.
For further advice, tips or information regarding cooking with induction, please contact your induction
cooktop manufacturer.

Page 12
6. Troubleshooting
Troubleshooting
If the product does not work:
Before you contact the service centre, make sure the product is plugged in, the electrical fuse
(on selected models) is in correctly and electrical wiring is connected. Do not take any action that
will damage the product.
Check electric connection. Voltage of the electric network should be between 220 - 240V, rangehood should be connected to grounded plug and turned on. Check rangehood’s motor switch. Ensure that there is power to the rangehood, the motor is connected to the rangehood and the rangehood is switched on. Check lamp switch. Lamp switch should be at “on” position. Check metal lter. Metal lter should be washed regularly, see lter cleaning. Check lamps. Lamps should be rm. Check outlet. Outlet should be open. Check lamps. Make sure they are not broken or faulty. Replace if broken. Please make sure there is no obstruction in ducting and back draft ns. Check the outlet, make sure it is not blocked and you have the correct diameter ducting installed. Check Isodrive installation manual, make sure the exi ducting is installed correctly, eg. Length of ducting used, keep the ducting taut. Check motor to make sure it hasn’t been obstructed or damaged by ying debris.
Rangehood does not work X X
Light does not work X X X X
Rangehood air suction is weak X X X X X
Rangehood does not direct
air out X X X
Loud noise from the rangehood X X X X

Page 13
7. Service
Faulty Installation
It is not the responsibility of Schweigen to rectify any incorrect installations. A service call out fee will be
charged for any Schweigen technician that attends a call, whereby it is established that the fault is due to
an incorrect installation or non-manufacturing fault. Should the appliance be installed in such a way that
the service agent is unable to gain access to the appliance, the person/s who own the premises or the
property where the appliance resides — will be responsible to provide access to the appliance at their
expense.
Service
In the event that the failure is not due to the
faults mentioned in Troubleshooting, contact
the customer service centre.
In Australia,
Customer Service 1300 829 066
In New Zealand,
Customer Service 0800 200 510
Lodging an Online Service Request
In the event that failure is not due the reason/s
in the trouble shooting section, you can lodge an
online Service Request. To lodge Service Request,
visit our website https://www.schweigen.com.
au/service-and-warranty and click on the link and
complete the service request form.
A service request will require the following
information:
• The purchase date
• The model number
• Therangehood model and motor type (eg.
IsoDrive 650)
• The serial number or batch number (this number
is on a sticker inside the rangehood).
• A copy of the purchase receipt (without a receipt
your service request cannot be processed).

Page 14
8. Specications
Technical Specications
Model EV-6UCQ & EV-9UCQ
Feeding Voltage 220-240V 50Hz
Lamp Power 2 x 25W
Approval Number
DIMENSIONS
EV-6UCQ
EV-9UCQ
866
900mm
261
295
245
237
267
30
245
600mm
566
295
261
237
267
30

Page 15
9. Disclaimer
Disclaimer
Under our policy of continuous product development, product specications may change without notice.
Prospective purchasers should therefore check with the retailer to ensure this publication correctly
describes the products being oered for sale. All information supplied is to be used for general reference
purposes only and is on the understanding that Scandium will not be liable for any loss, liability or
damage of whatever kind arising as a result of any reliance upon such information. All pictures used in the
guide are for illustrative purposes only.
The symbol on the product or its packaging indicates that it cannot be
treated as normal household waste. Take this product to your nearest
electrical and electronic equipment waste point for recycling. By correctly
disposing of this product, you will be helping to prevent potentially negative
consequences for the environment and public health, which could arise if
this product is not handled in the appropriate way. For more details about
the recycling of this product please contact the authorities of your city or
town, your local household waste service or the store where you purchased
the product.

Australia 8/3-4 Anzed Court, Mulgrave 3170 Victoria. Phone [phone]
Email [e-mail] Web www.schweigen.com.au
New Zealand 5 Tolich Place, Henderson, Auckland 0610. Phone [phone]
Email info.par[email protected]om Web www.parex.co.nz