SCM IrDA-ZIO User manual

USER’S MANUAL
USB TO IrDA ADAPTER
SCM IrDA-ZIO ( Y-160 )
1. Introduction
IntroductionIntroduction
Introduction
USB to IrDA bridge adapter is for enabling IrDA wireless data communication
through a standard USB port. Powered from USB bus, this product does not require
any external power adapter. It supports SIR (2.4Kbps to 115.2Kbps), MIR (576Kbps
to 1152Kbps), and FIR (4Mbps) modes. The effective data transmission distance is
from 0 to 1M. The reception or viewing angle in a typical environment is 30o (+ / - 15o).
Use the product; you could transfer data with wireless connection for PC, PDA,
digital camera, scanner and printer.
2.
2.2.
2. Application & Connection
Application & ConnectionApplication & Connection
Application & Connection
Wireless data transfer between desktop PC and notebook PC, PDA, Digital Camera,
Scanner and Printer
Files Sharing, Photo transfer, Printing, Data Exchange and Synchronization

SCM PC-Card GmbH www.scm-pc-card.de USB To Irda Adapter User’s Manual 1
3.
3.3.
3. Package Content
Package ContentPackage Content
Package Content
Hardware
 USB to IrDA Adapter, USB Cable
Software
 Software driver on CD
 User’s Manual
4.
4.4.
4. Product Features
Product FeaturesProduct Features
Product Features
 Easily enable IrDA function on the desktop PC through USB port
 USB Plug and Play convenience
 Fully compatible with IrDA 1.1 and USB 1.1 specification
 Compatible with FIR 4Mbps, MIR, SIR and ASK 56Kbps
 No power adapter required
 Low power consumption
5.
5.5.
5. System Requirements
System RequirementsSystem Requirements
System Requirements
 IBM PC 486DX4-100 MHz or higher or compatible system
 Available USB port
 CD-ROM drive
 Windows®98, Windows®ME, Windows®2000, Windows®XP.
6.
6.6.
6. Driver Installation
Driver InstallationDriver Installation
Driver Installation
NOTICE: Before you install the driver to your computer, please do not connect
the USB to IrDA Adapter to your computer.

SCM PC-Card GmbH www.scm-pc-card.de USB To Irda Adapter User’s Manual 2
6.1 Windows®98 Driver Installation
Following the steps below to install driver of SCM PC-Card USB to IrDA Adapter:
6.1.1 Power on the computers that you will connect the USB to IrDA Adapter
and make sure the USB port is enabled and can working properly.
6.1.2 Put the driver CD into the CD-ROM. The CD will start automatically and
will show you the startscreen. If autostart is disabled on your system,
please run the D:\WinDriver\SETUP.EXE
6.1.3 As the windows appear as below, click “NEXT” to continue.

SCM PC-Card GmbH www.scm-pc-card.de USB To Irda Adapter User’s Manual 3
6.1.4 You can choose the destination folder that you want to install or use the
default setting (C:\WINDOWS\Sigmatel\USB-IR).
6.1.5 The windows will install the driver into your system.
6.1.6 As the Windows appear as below, please plug the USB to IrDA
Adapter into the USB port.
6.1.7 Windows will detect the new device, in this procedure you may have to
put your Win98CD into the CD-ROM

SCM PC-Card GmbH www.scm-pc-card.de USB To Irda Adapter User’s Manual 4
6.1.8 Windows will detect the new device (SigmaTel USB-IrDA Adapter) and
install the driver.
6.1.9 As the windows appear as below, you have to reboot your computer.
6.1.10 After the windows restart, you have to check “My Computer”-“Control
Panel”-“System”-“Device Manager”, you can see a new “Infrared
Communication Device” appear and “SigmaTel USB-IrDA Adapter”
under the Network Adapter, “Virtual Infrared COM Port” and “Virtual
Infrared LPT Port” under the Ports (COM & LPT) item.

SCM PC-Card GmbH www.scm-pc-card.de USB To Irda Adapter User’s Manual 5
6.2 Windows®ME Driver Installation
Driver InstallationDriver Installation
Driver Installation
Following the steps below to install driver of SCM PC-Card USB to IrDA Adapter:
6.2.1 Power on the computers that you will connect the USB to IrDA Adapter
and make sure the USB port is enabled and working properly.
6.2.2 Put the driver CD into the CD-ROM. The CD will start automatically and
will show you the startscreen. If autostart is disabled on your system,
please run the D:\WinDriver\SETUP.EXE
6.2.3 As the windows appear as below, click “NEXT” to continue.

SCM PC-Card GmbH www.scm-pc-card.de USB To Irda Adapter User’s Manual 6
6.2.4 You can choose the destination folder that you want to install or use the
default setting (C:\WINDOWS\Sigmatel\USB-IR).
6.2.5 The windows will install the driver into your system..
6.2.6 As the Windows appear as below, please plug the USB to IrDA
Adapter into the USB port.

SCM PC-Card GmbH www.scm-pc-card.de USB To Irda Adapter User’s Manual 7
6.2.7 Windows will detect the new device (Sigmal Tel USB-IrDA Dongle) and
install the driver for the new device.
6.2.8 As the windows appear as below, you have to reboot your computer.
6.2.9 After the windows restart, you have to check “My Computer”-“Control
Panel”-“System”-“Device Manager”, you can see a new “Infrared
Communication Device” appear and “SigmaTel USB-IrDA Dongle”
under the Network Adapter, “Virtual Infrared COM Port” and “Virtual
Infrared LPT Port” under the Ports (COM & LPT).

SCM PC-Card GmbH www.scm-pc-card.de USB To Irda Adapter User’s Manual 8
6.3 Windows®2000 Driver Installation
Driver InstallationDriver Installation
Driver Installation
Following the steps below to install driver of SCM PC-Card USB to IrDA Adapter:
6.3.1 Power on the computers that you will connect the USB to IrDA Adapter
and make sure the USB port is enabled and can working properly.
6.3.2 Put the driver CD into the CD-ROM. The CD will start automatically and
will show you the startscreen. If autostart is disabled on your system,
please run the D:\WinDriver\SETUP.EXE
6.3.3 As the windows appear as below, click “NEXT” to continue.

SCM PC-Card GmbH www.scm-pc-card.de USB To Irda Adapter User’s Manual 9
6.3.4 You can choose the destination folder that you want to install or use the
default setting (C:\WINNT\SigmaTel\USB-IR), then click “NEXT” to
continue.
6.3.5 Windows will install the driver into your computer.
6.3.6 When the Windows appears as below, plug the USB to IrDA Adapter
into the USB port and click “Finish” to completed the installation step.