Scosche GoPro PSM31001 User manual

BASE-CLAMPS
HOW IT WORKS:
STEP 1
Select the right size clamp
(Various sizes sold
separately)
STEP 2
Select the base & ring
c
lamp that coinc i des wi th
what you need to mount
2A . Use protective film to
prevent any pa i nt
damage 28 .
STEP3
Lock it in place
The self locki ng clamp design
allows foreasy for easy one
person installatio
n. Simply slip the
clamp over tube and lock in your
base, secure using the stainless
mounting hardware and you are
ready
to Mount Up and Move Out.
NOTE: Ring clamps 2" & over in size may
require pre-stretching
to help spread the
clamp over the tube . (Use Protective film
when mounting)
For complete warranty details, please visit us at
www.scosche.com or call [phone]
Register your product online at
www.scosche.com/register
PSM31001
CAMERA I GoPro ® MOUNT BASE
PARTS INCLUDED
(1) Camera Base Adjustment Mount
(1) 1 /4" -20 Screw Mou nt
(1) Go Pro
111
Mount
TOOLS REQUIRED (Not Included)
3/ 1 6" Hex (Allen) Key, E xcept where noted
+---*Ring Clamps
NOT I ncluded
*VARIOUS RING CLAMP SI ZES SO LD SEPAR AT ELY W/ HARDWAR E
PSC21006 -BaseCiamp 1.5" Tube Clamp
PSC21007 -BaseCiamp 1.625" Tube Clamp
PSC21009 -BaseCiamp 1.75" Tube Clamp
PSC210010- BaseCiamp 1.85" Tube Clamp
PSC210011 -BaseCiamp 1.875" Tube Clamp
PSC21012 -BaseCiamp 2" Tube Clamp

DEVICE SETUP GUIDE
MOUNTING ADAPTER for GoPro®
Requires GoPro ~ camera with waterproof case (not included).
1. Attach ball adapter
to the mounting base as show below.
2. Placethe camera case ontothe adapter so
that the two
mounting brackets on the case fit between the (3) mounting
brackets on the adapter
as shown (A). Make sure the holes
on both sets
of brackets are aligned.
3. Insert the threaded end
of the clamping arm into the
bracket holes
(B) , and thread into the threaded nut
at the opposite end and tighten until snug
(C).
Loosen the arm to adjust the angle of the camera.
PSM31001
1/4 "THREADED MOUNTING ADAPTER
for devices with a 1/4' threaded mount
1. Attach the ball adapter to the mounting base as shown on the
following page.
2. Screw the 1/4" threaded mounting adapter directly into the 1/4"
mounting hole on device.
Camera/GoPro® Mount Base
STEP 1
Choose a mounting location (D).
STEP2
Mount base to the appropriate sized clamp ring for the vehicle (E*).
Note: Do not exceed 200 inch-pounds
STEP3
Position the base into location by clicking clamp rings into the base.
Then use a 3/16" hex key to fasten the screw & nut (F) included with
the ring clamp*. Continue until
clamp is tight and does not move.
Note: Do not exceed 200
inch-pounds
STEP4
Tighten/Loosen the ball and hinge
joint
using the mounted turn
knob (G) on
the
mount base.
Note: Use the knob to
loosen, tighten or switch-out the
1/4" -20 screw mount (I)
or the Go Pro® mount (H ).
Clamp Removal:
In-order to remove the tube clamp from location, the clamp must
first betightened
to allow base remova l. Once tightened, loosen
the clamp and carefully squeeze clamp
to remove from the
location.
Note : Use protective fi lm to hel p avoid damageto the p ai nt. *Variou s
ri ng cla mp si zes available (sold se para te ly w/ hardwa re