Scott Living 1031FM-26-216 Quickspecs

Questions, problems, missing parts?
Before returning to your retailer,
call our customer service department at
1-855-571-1044
9 a.m. - 5 p.m., EST, Monday - Friday.
www.greentouchhome.com
Français p. 18
Español p. 36
Date Purchased _______________________
Concave Media Mantel
with 26-IN Infrared
Electric Fireplace
MODEL # 1031FM-26-216
ASSEMBLY, CARE & USE INSTRUCTIONS
ITEM # 0781465
TM

2
PACKAGE CONTENTS
PART DESCRIPTION QUANTITY
A Top 1
B Center Panel 1
C Left Middle Wall 1
D Right Middle Wall 1
E Left Wall 1
F Right Wall 1
G Left Door 1
H Right Door 1
I Shelf 2
J Back Panel 2
K Base 1
L Wood Door Panel 2
M Insert 1
N Remote Control 1
N
M
A
B
C
D
E
F
G
H
I
I
J
J
K
L
L
O
O Battery 2
M

3
HARDWARE CONTENTS (NOT SHOWN ACTUAL SIZE)
PART DESCRIPTION QUANTITY
AA Wooden Dowel 2020
BB Bolt 18
CC Washer 18
DD Back Panel Screw 22
EE Short Screw 16
FF Shelf Pin 8
GG Touch-up Pen 1
SAFETY INFORMATION
Please read and understand this entire manual
before attempting to assemble, operate or install
the product.
This equipment has been tested and found to
comply with the limits for Class B digital devices,
pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. The equipment generates, uses
and can radiate radio frequency energy and, if
not installed and used in accordance with the
instructions, may cause harmful interference
to radio or television reception, which can be
determined by turning the equipment off and
on. The user is encouraged to try and correct
the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna
•Increase the separation between the
equipment and the receiver
• Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
This device complies with Part 15 of the FCC
rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful
interference, and
2. This device must accept any interference
received, including interference that may
cause undesired operation.
AA BB CC DD EE FF GG

4
Modifications not approved by the party
IMPORTANT INSTRUCTIONS
gasoline, paint or flammable vapors or liquids
are used or stored. This fireplace should not be
by the manufacturer and may cause fire,
Any repairs to this fi replace should be carried
out by a qualifi ed service person.
Under no circumstances should this fi replace
be modifi ed. Parts having to be removed for
SAFETY INFORMATION (CONT’D)
responsible for compliance could void user’s
authority to operate the equipment.
This Class B digital apparatus complies with
Canadian ICES-003.
When using electrical appliances, basic precau-
tions should always be followed to reduce the risk
DANGER
ton si launam siht ni noitamrofni eht fI •
result causing property damage, personal
injury or loss of life.
•
and LCD televisions (up to 56 inches and
weighing a maximum of 65 pounds). Using
this item with loads heavier than the stated
maximum can result in tipping and/or
instability, which can result in injury or even
death.
WARNING
• This appliance is hot when in use. To avoid
burns, DO NOT let bare skin touch hot
surfaces. Keep combustible material, such as
furniture, pillows, bedding, papers, clothes and
curtains at least 3 feet from this appliance and
keep them away from the sides and rear.
• Extreme caution is necessary when any heater
is used by or near children or individuals with
operating and unattended.
• DO NOT run cord under carpeting. DO NOT
cover cord with throw rugs, runners, or similar
and where it will not be tripped over.
• DO NOT insert or allow foreign objects to enter
any ventilation or exhaust opening as this may
appliance.
• This appliance has hot and arcing or sparking
parts inside. DO NOT use it in areas where
used as a drying rack for clothing. Christmas
stockings or decorations should not be hung in
the area of it.
• Use this appliance only as described in the
manual. Any other use is NOT recommended
electric shock or injury to persons.
CAUTION
• If possible, ALWAYS unplug this appliance
when not in use.
• DO NOT operate any heater with a damaged
cord or plug or after the heater malfunctions.
DO NOT operate any heater if it has been
dropped or damaged in any manner.
Disconnect power at service panel and have
heater inspected by a reputable electrician
before reusing.
•
•
servicing must be replaced prior to operating
• DO NOT use outdoors.
• This heater is not intended for use in
bathrooms, laundry areas and similar indoor
locations.
NEVER place heater where it may fall into a
bathtub or other water container.
• To disconnect this appliance, turn controls to
the off position, then remove plug from outlet.
• ONLY connect to properly grounded outlets.
• This appliance, when installed, must be
electrically grounded in accordance with local
codes, with the current CSA C22.1 Canadian
Electrical Code or follow U.S.A. Installations,
follow local codes and the National Electrical
Code, ANSI/NFPA N0.70.
of fi re, electric shock and injury to persons, includ-
ing the following:
followed exactly, an electric shock or fire may
This product is intended to fit most plasma
disabilities and whenever the fireplace is left
cause an electric shock or fire, or damage the
coverings. DO NOT route cord under funiture or
appliances. Arrange cord away from traffic areas
• Read all instructions before using this heater.

5
To prevent a possible fire,
Preferably, the fireplace will be on a dedicated
SAVE THESE INSTRUCTIONS
SAFETY INFORMATION (CONT’D)
A B C D
Grounding Pin Grounding Pin
Grounding Means
Metal
Screw
Cover of
Grounding
Box
Adapter
•DO NOT block
air intakes or exhaust in any manner. DO
NOT use on soft surfaces, like a bed, where
opening may become blocked.
•The heater MUST NOT be located
immediately below a socket-outlet.
•ALWAYS plug heaters directly into a wall
outlet / receptacle. NEVER use with an
extension cord or re-loadable power tap (outlet
/ power strip).
• DO NOT slide insert on top of wood to avoid
scratching wood surface.
• DO NOT place any object on top of the insert
or block the air intakes / vents as this can
cause the unit to overheat and could cause
a fire.
Electrical Connection
•A 15-Amp, 120-volt, 60 Hz circuit with
a properly grounded outlet is required.
circuit as other appliances on the same circuit
may cause the circuit breaker to trip or the
fuse to blow when the heater is in operation.
The unit comes standard with 6-ft. three-wire
DO NOT exceed the current rating of the
current tap.
•This heater is for use on 120 volt. The cord
has a plug as shown below. See illustration
for grounding instruction. An adapter as
shown at C is available for connecting
three-blade grounding type plugs to two-
slot receptacles. The green grounding
lug extending from the adapter must be
connected to a permanent ground such as
a properly grounded outlet box. The adapter
should not be used if a three-slot grounded
receptacle is available.
cord, exiting from the rear of the fireplace.
Grounding Instructions

6
Before beginning assembly of product, make
sure all parts are present. Compare parts with
package contents list and hardware contents list.
If any part is missing or damaged, do not attempt
to assemble the product.
Estimated Assembly Time: 45 minutes
Tools Required for Assembly (not included):
Phillips screwdriver
1. Insert two wooden dowels (AA) into each side of
center panel (B)
2. Align the dowels in center panel (B) to left middle
wall (C) and right middle panel (D). Insert dowels
into predrilled holes and press tight.
1
H
F
CC
1
2
Hardware Used
Wooden Dowel x 4
AA
AA BB CC DD EE FF GG HH II
PREPARATION
ASSEMBLY INSTRUCTIONS
B
AA
AA
B
C
D

7
3. Insert four wooden dowels (AA) into base (K).
4. Place assembly from Step 2 onto base (K), securing
with four washers (CC) and four bolts (BB).
5. Insert two wooden dowels (AA) into outer holes on
right side of base (K). Attach right wall (F), securing
with two washers (CC) and two bolts (BB).
Repeat for left wall (E).
ASSEMBLY INSTRUCTIONS (CONT’D)
3
4
1
1
2
5
1
2
Wooden Dowel x 4
CC
AA BB CC DD EE FF GG HH II
Hardware Used
Wooden Dowel x 4
AA
AA BB CC DD EE
Hardware Used
Hardware Used
Bolt
Bolt
Washer
Washer
x 4
x 4
x 4
x 4
BB
AA
CC
BB
AA BB CC DD EE FF GG
AA BB CC DD EE FF GG HH II
AA BB CC DD EE FF GG HH II
BB CC DD EE FF GG HH II
K
AA
AA
K
BB
CC
K
BB
CC
AA
F

8
ASSEMBLY INSTRUCTIONS (CONT’D)
6. Insert two wooden dowels (AA) into the top
outer holes on left wall (E), left middle wall
(C), right middle wall (D) and right wall (F).
Attach top (A), securing from underneath
with ten washers (BB) and bolts (CC).
6
1
2
1
Hardware Used
Bolt
Washer
x 10
x 10
AA
BB
AA BB CC DD EE FF GG HH II
AA BB CC DD EE FF GG HH II
Wooden Dowel x 8
CC
AA BB CC DD EE FF GG HH II
A
BB
CC
AA
E
C
D
F

9
7. From behind the assembly, attach back panel (J)
to shelving areas using back panel screws (DD).
Repeat for remaining back panel (J).
8. Insert shelf pins (FF) at desired height, ensuring
they are level. Place shelf (I) on top of shelf pins
(FF).
Repeat for remaining the shelf (I).
ASSEMBLY INSTRUCTIONS (CONT’D)
7
1
2
8
1
2
Hardware Used
Back Panel Screw x 22
DD
AA BB CC DD EE FF GG
Hardware Used
Shelf Pin x 8
FF
AA BB CC DD EE FF GG HH II
9. Align the holes of the preassembled hinges on
right door (H) with the corresponding holes on
right wall (F). Attach right door (H) using four
short screws (EE) each.
9
1
2
Hardware Used
Short Screw x 4
EE
GG HH II
J
DD
I
FF
H
EE
F

10
10. Secure inside of right door (H) hinges with four
short screws (EE).
Repeat steps 9-10 for the left door (G).
ASSEMBLY INSTRUCTIONS (CONT’D)
10
1
Hardware Used
Short Screw x 12
EE
AA BB CC DD EE FF GG HH II
11. From behind the assembly, remove the
preassembled insert brackets from the middle area.
Save brackets and screws for future use.
12. With the help of another person, position insert (M)
into middle opening of mantel assembly.
Note: DO NOT plug insert (M) into power outlet
yet.
CAUTION: DO NOT slide insert on top of wood to
avoid scratching wood surface.
11
Note: Before proceeding to the next step, with the help of another person, move the mantel close to
H
EE
12
M
2
2
2
1

11
ASSEMBLY INSTRUCTIONS (CONT’D)
1. Remove the silicone trim along the outer edges of the glass panel on the inside of the door. Start
at a corner and pull to remove the four pieces. Be careful not to damage the silicone trim as it will
be used to secure the new panel.
2. Remove the glass panel from the door frame, then insert the included wood door panel (L).
2
1
13. Re-attach insert brackets with previously
removed screws to secure insert (M).
Assembly is now complete. With the help of
another person, move the assembly to the final
desired location. Once in final position you may
plug the insert (M) into the power outlet.
13
1
2
1
CHANGE DOOR PANELS (OPTIONAL)
2
1
3
2
1
3
Note: The pre-installed glass door panels can be switched out with the included wood door panels (L).
L
M
1
2
3
4
1
2
3
4
Using your finger press the silicone trim back into place. Move around the outer edge of the panels
until all four sides are secure.

12
OPERATING INSTRUCTIONS
Power Function
•Press the POWER ICON to turn the main power to the unit ON or OFF.
•When the unit is powered ON, the lights under the emberbed will glow to indicate the unit
has power.
•If any functions are stored in memory then they will resume at the last setting .
Flame Brightness Function
•
•If the unit main power is OFF, you can press the FLAME BRIGHTNESS ICON to power ON
•
Note: The control panel is a touch screen. It will appear black. Touch the control panel once to
“wake up” the controls. This will cause the controls to light up. Which ever icon you touch will display
it’s last setting when you do this. At this time you can press the corresponding icon to the function you
would like to adjust. After 5 seconds the touch screen will fade to black.
Control Panel Remote Control
Temperature Function
•Press the TEMPERATURE ICON to adjust the heater’s thermostat setting.
•If the unit is powered OFF, you can press the TEMPERATURE ICON to power ON the unit.
The emberbed will glow at the lowest brightness setting unless a different setting was saved
in the memory.
M
Press the FLAME BRIGHTNESS ICON to adjust the flame brightness.
Press the FLAME BRIGHTNESS ICON again to scroll up through the flame brightness
settings: 1, 2, 3, 4, 5, OFF.
the unit and flame brightness will resume at the last setting.
To use the remote control,
first insert two AAA batteries
(included) into the remote
control. ensure the poplarities
of the battery match the inside
of the battery compartment.
•:sgnitteserutarepmettes-erpehthguorhtpullorcsotniagaNOCIERUTAREPMETehtsserP
The thermostat setting range is 65oF(18oC) to 90oF (32oC), HI(High) and OFF.
•.suisleCdnatiehnerhaFneewtebelggototsdnoces5rofNOCIERUTAREPMETehtnwoddloH
An “F” or “C” will display next to the temperature.
•Press and hold the TEMPERATURE ICON for 10 seconds to disengage the heater function.
Press and hold the TEMPERATURE ICON for 10 seconds again to engage the heater
function. (See HEATER OVERRIDE section below for more details).
•
•Set the temperature to "HI" to have the heater run continually.
Press and hold the TEMPERATURE & TIMER ICON for 5 seconds to toggle between 5oF
(3oC) increments and 1oF (1oC) increments when setting the temperature. The unit will beep to
indicate that the change has taken place. The factory default temperature is 5oF (3oC) increments.
M8:88

13
OPERATING INSTRUCTIONS (CONT’D)
Timer Function
•Press the TIMER ICON to set the countdown for the unit’s main power.
•
•Press the TIMER ICON again to scroll through the timer settings, which are: 30, 1h, 2h, 3h,
4h, 5h, 6h, 7h, 8h, 9h,OFF.（30 means 30 minutes)
•When the timer reaches zero, it will turn OFF the main power and will maintain all the settings
in memory.
Downlight Function
•Press the DOWNLIGHT ICON to power the LED downlights ON or OFF
•If the unit is powered OFF, you can press the DOWNLIGHT ICON to power ON the unit. The
emberbed will glow at the lowest brightness setting unless a different setting was saved in
the memory.
MEMORY FUNCTION
This unit has a memory function that allows you to turn off the MAIN POWER and retains all the other
function settings (excluding the TIMER function).
•When the unit’s main power is OFF, press the POWER ICON once on the insert control panel or
on the remote control to power the unit ON and “wake up” the individual function at the last setting.
Press the icon again to adjust it and press the main POWER ICON on the insert or on the remote
control to turn the unit OFF and save the new setting into memory.
•When the unit is powered ON, the LED readout will show the saved temperature setting. If a
HEATER OVERRIDE
The power to the heater can be disengaged to prevent the heater from being accidentally or
unintentionally powered on. This feature is primarily added to help prevent children from powering
on the heater when it is not desired.
•To engage the heater override function press and hold the HEATER ICON for 10 seconds. The
symbol E3 will display and then go blank while beeping 3 times. The heater function is now
locked. If the HEATER ICON is pressed again E3 will appear then fade.The Flame, Downlight
and Timer functions will operate normally. Only the heater and blower are disengaged.
•To unlock the heater function, press and hold the HEATER ICON for 10 seconds. The symbol
E3 will display and then go blank while beeping 3 times. The heater function is now engaged.
By pressing the HEATER ICON again you will be able to adjust the heat temperature to your
desired temperature.
•To reset the memory, hold down the main POWER ICON for 10 seconds at any time. When this
happens, the LED readout will blink with three zeros three times the unit will be shut down.
•Another way to reset the memory is to unplug the unit from the wall.
If the unit is powered OFF, you can press the TIMER ICON to power ON the unit. The
emberbed will glow at the lowest brightness setting unless a different setting was saved in
the memory.
temperature setting was not saved, it will show the flame brightness setting saved in memory. If
neither one has a setting saved to memory, then only the emberbed will glow (as a power light
indicator).

14
CARE AND MAINTENANCE
Disposal of Used Battery
A battery may contain hazardous substances that could be
endangering the environment and
human health.
•This symbol marked on the battery and/or packaging indicates that
used battery shall not be treated as municipal waste. Instead it shall
be left at the appropriate collection point for recycling.
•By ensuring the used battery is disposed of correctly, you will help
prevent potential negative consequences for the environment and
human health. The recycling of materials will help to conserve
natural resources.
For more information about collection and recycling of used batteries,
please contact your local municipality, your waste disposal service or
the point-of-sale where you purchased this battery.
Cleaning
Replacing the Remote Control Batteries
When the remote control (N) stops operating or its
range seems reduced, it is time to replace the
batteries. Note:The batteries should be removed if the
product is to be left unused for a long time.
1. The battery compartment is located on the back
of the remote control (N).
2. Remove battery cover from the back of remote
control (N) and remove old batteries.
3. Insert 2pcs AAA batteries, ensuring the polarities of
the battery match the inside of the battery
compartment.
4. Re-insert the battery door.
Note: Do not mix old and new batteries.
Do not mix alkaline, standard (carbon zinc), or rechargeable (nicad, nimh, etc) batteries.
Non-rechargeable batteries are not to be recharged. Exhausted batteries are to be removed from
the product.
Harmful if swallowed.
N
• Make sure the unit is turned OFF, unplugged and the heating elements of heater are cool
whenever you are cleaning the heater or fireplace.
• Clean the metal trim using a water-dampened soft, clean cloth. DO NOT use brass polish or
household cleaners as these products will damage the metal trim.
•
bearing life and require no further lubrication. However, periodic cleaning/vacuuming of the fan/
heater and air intake/output vents is recommended.
The motors used on the fan and the flame generator assembly are pre-lubricated for extended
• Any other servicing should be performed by an authorized service representative.
When the heater is not in use, the power cord should be stored properly to avoid contact with hot
or sharp objects.
•

15
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Error E1 displayed on
control panel.
The overheat sensor
has been engaged.
Unplug unit, wait 15-20 minutes, then the sensor will reset
itself. Plug the unit back in and turn on the heater. If the
problem persists, call customer service.
Note: The other functions will work normally excluding
the heater. Until the problem is solved, the error will only
appear/sound when the heater button is pressed.
Error E2 displayed on
control panel.
The thermostat
sensor is broken or
not working correctly.
Unplug unit, wait 15-20 minutes, then the sensor will reset
itself. Plug the unit back in and turn on the heater. If the
problem persists, call customer service.
Note: The other functions will work normally excluding
the heater. Until the problem is solved, the error will only
appear/sound when the heater button is pressed.
Error E3 displayed on
control panel.
Heater override
function is engaged
No power; logs do not
glow.
The unit does not
have power.
Check that the power cord is securely plugged into a
standard 120V outlet. Then check to make sure the unit is
powered on.
are glowing. powered off. achieved.
Heater and blower
do not power on but rest
of functions are working.
Power cord gets warm to
the touch.
Normal operation. This is normal for a heater appliance as it requires
more current to operate. Check the connections of
the appliance cord and the outlet. Make sure the plug
and outlet frequently to determine if it is HOT; if so,
discontinue use of the appliance and consult with a
outlet(s).
Remote control does not
work.
Weak or failing
batteries.
Replace with 2 AAA batteries (See page 14 for more
information.)
Remote control
signal is weak and only
works sometimes.
Pressing the buttons
too quickly.
Press the buttons slowly and steadily to ensure the
transmitter recognizes the request.
Using the remote
control too far away or
at an off angle.
Move closer to the insert; the remote control will only
work within a distance of 20 feet and 45 degrees to either
Fan motor continues to
blow after unit is powered
of.
Normal operation. This is a standard feature; the blower runs for an
additional time to cool off heater tubes.
TROUBLESHOOTING
Heater override
function is engaged
To unlock the heater, simply press and hold the
temperature button for 10 seconds (See page 13
Heater Override Section for more details).
To unlock the heater, simply press and hold the
temperature button for 10 seconds (See page 13
Heater Override Section for more details).

16
The manufacturer warrants that your new Electric fireplace is free from manufacturing and material
defects for a period of one year from date of purchase, subject to the following conditions and
limitations.
Install and operate this Electric fireplace in accordance with the installation and operating instructions
furnished with the product at all times. Any unauthorized repair, alteration, willful abuse, accident, or
misuse of the product shall nullify this warranty.
This warranty is non-transferable, and is made to the original owner, provided that the purchase was
made through an authorized supplier of the product.
The warranty is limited to the repair or replacement of part(s) found to be defective in material or
workmanship, provided that such part(s) have been subjected to normal conditions of use and
The manufacturer may, at its discretion, fully discharge all obligations with respect to this warranty by
refunding the wholesale price of the defective part(s).
Any installation, labor, construction, transportation, or other related costs/expenses arising from
defective part(s), repair, replacement, or otherwise of same, will not be covered by this warranty, nor
shall the manufacturer assume responsibility for same.
The owner/user assumes all other risks, if any, including the risk of any direct, indirect or
consequential loss or damage arising out of the use, or inability to use the product, except as
provided by law.
All other warranties—expressed or implied—with respect to the product, its components and
accessories, or any obligations/liabilities on the part of the manufacturer are hereby expressly
excluded.
The manufacturer neither assumes, nor authorizes any third party to assume on its behalf, any other
liabilities with respect to the sale of the product.
The warranties as outlined within this document do not apply to non accessories used in conjunction
with the installation of this product.
This warranty is void if:
2. Any unauthorized alteration, willful abuse, accident, or misuse of the product.
3. You do not have the original receipt of purchase.
ONE-YEAR LIMITED WARRANTY

17
For replacement parts, call our customer service department at 1-855-571-1044, 9 a.m. - 5 p.m., EST,
Monday - Friday.
PART DESCRIPTION PART #
IShelf
PF-1031FM-26-216-002
BCenter Panel
PF-1031FM-26-216-001
GLeft Door
(with Hinges)
PF-1031FM-26-216-003
HRight Door
(with Hinges)
PF-1031FM-26-216-004
LWood Door
Panel
PF-1031FM-26-216-005
TGlass Door
Panel PH-
1031FM-26 -001
HH Hardware
pack PH-
1031FM-26 -002
II Knob and
Screw PH-
1031FM-26 -003
JJ Hinge (with
screws) PH-
1031FM-26 -004
PART DESCRIPTION PART #
KK
Insert Mounting
Bracket (with
screws)
PU16-232628-MB
LL
Magnetic Door
Catch and
Screws
PH- 1031FM-26 -005
M
26” Concave
Curved Glass 2612-CCG
Fireplace insert
NRemote Control
PThermostat PU16-232628-NTC
QHeater/Blower
Assembly PU16-HBCC
RSpinner Motor PU16-23262833-SM
SPCB Board PU16-262833-PCB
REPLACEMENT PARTS
I B T
Q
G H
HH
P
L
M N
II JJ KK LL MM
R S
MM Glide (2)
PH-1031FM-26-006
PU16-262833-RC

Des questions, des problèmes, des pièces manquantes?
Avant de retourner l’article au détaillant,
appelez notre service à la clientèle au
1-855-571-1044, entre 9 h et 17 h (HNE), du lundi au vendredi.
www.greentouchhome.com
English p. 1
Español p. 36
Date d’achat _______________________
Médium de cheminée
concave avec foyer Électrique
Infrarouge de 26 pouces
MODÈLE # 1031FM-26-216
INSTRUCTIONS D’UTILISATION, D’ASSEMBLAGE
ET DE MAINTENANCE
ARTICLE # 0781465
TM

19
CONTENU DE L’EMBALLAGE
A Dessus 1
B Panneau central 1
C Cloison centrale gauche 1
D Cloison centrale droite 1
ECloison gauche 1
FCloison droite 1
G Porte gauche 1
H Porte droite 1
I Tablette 2
J Panneau arrière 2
K Base 1
LPanneau de porte en bois 2
MFoyer encastrable 1
N Télécommande 1
O Pile 2
PIÈCE DESCRIPTION QUANTITÉ
N
M
A
B
C
D
E
F
G
H
I
I
J
J
K
L
L
O
M

20
CONTENUS MATÉRIELS (NON REPRÉSENTÉS EN TAILLE RÉELLE)
PIÈCE DESCRIPTION QUANTITÉ
AA Groujon en bois 20
BB Boulon 18
CC Rondelle 18
DD Vis pour le panneau arrière 22
EE Vis courte 16
FF Goupille à tablette 8
GG Crayon à retouche 1
AA BB CC DD EE FF GG
CONSIGNES DE SÉCURITÉ
Assurez-vous de lire et de comprendre l’intégralité
du présent manuel avant de tenter d’assembler,
d’installer ou d’utiliser l’article.
Cet article a été testé et déclaré conforme aux
limites imposées aux dispositifs numériques de
classe B, conformément à l’alinéa 15 du règlement
de la FCC. Ces limites sont destinées à assurer
une protection raisonnable contre les interférences
nuisibles dans un environnement résidentiel.
Cet article génère, utilise et peut émettre de
l’énergie radiofréquence et, s’il n’est pas installé
et utilisé conformément aux instructions, risque
de provoquer des interférences nuisibles lors de
la réception d’émissions de radio ou de télévision
successivement l’article). L’utilisateur devra
prendre les mesures nécessaires suivantes pour
tenter d’éliminer ces interférences :
• réorienter ou déplacer l’antenne réceptrice;
• accroître la distance entre l’appareil et le
récepteur;
• brancher l’appareil sur une prise de courant
appartenant à un autre circuit que celui du
récepteur;
• obtenir de l’aide auprès du détaillant ou
d’un technicien en radio ou en télévision
expérimenté.
Cet appareil est conforme à l’alinéa 15 du
règlement de la FCC. Son utilisation est soumise
aux deux conditions suivantes :
1. cet appareil ne doit provoquer aucune
interférence nuisible; et
2. cet appareil doit accepter toute interférence
reçue, y compris des interférences susceptibles
de causer un fonctionnement non désiré.