SCT RemoteCam4 User manual

RemoteCam4™
Installation Instructions
www.soundcontrol.net 203-854-5701 ©SOUND CONTROL TECHNOLOGIES, INC. 2017
Thank you for choosing the Sound Control Technologies’ RemoteCam4™ camera integration kit!
Included in each RemoteCam4™ kit will be:
•1 Power Supply & cord (Currently all RemoteCam4™ Kits utilize
the WPS-12) to provide power for the RemoteCam4™ electronics
as well as the remote camera up to 300’ from the head end. The
power supply is AC 100-240V~47-63HZ compliant.
•1 RemoteCam4™ Head End Module (RC4-HE) which provides
system power, control interface (HDMI CEC, RX, TX, GND & IR) for
the camera & one HDMI video output for the codec.
•1 RemoteCam4™ Camera Module with PowerSniffer™ (RC4-CE)
that provides camera power, control (HDMI CEC, RX, TX, GND &
IR) and HDMI video input for the camera
•Documentation
•Specific cables (Part number according to the following chart)
Company
Codec
Camera
SCT Kit
Cables
Cisco
C40, C60, C90 & SX80
PrecisionHD 1080p 12X,
4xS1 & 720p
RC4-PHD
RCC-C001/RCC-C002/RCC-C003
RCC-H01/RCC-H003/RCC-H004
SX20 PrecisionHD 1080p 12x RC4-PSA
RCC-C001/RCC-C002
RCC-H009
C40, C60, C90 & SX80
PrecisionHD 1080p
4xS2, 2.5x
RC4-PSB
RCC-C009
RCC-H001/RCC-H003
SX20
PrecisionHD 1080p
4xS2, 2.5x
RC4-PSX
RCC-C009
RCC-H009
Lifesize
220
Icon 600
Icon 800
10X
Camera S RC4-L22
RCC-C001
RCC-C028
RCC-H001
Panasonic Generic Controller
AW-HE130
AW-HE40
RC4-P13
RC4-P40
RCC-C001/RCC-C006/RCC-C008
RCC-H001/RCC-H010/RCC-H004
Polycom Group Series
300, 500 & 700 EagleEye IV RC4-E4P RCC-C030
RCC-H030
Avaya/Radvision
XT5000/XT7100 EVI-HD7 RC4-R5X RCC-C004/RCC-C005/RCC-C006
RCC-H001/RCC-H004/RCC-H006
XT1000/XT1200 EVI-HD3 RC4-RHD RCC-C004/RCC-C005/RCC-C006
RCC-H001/RCC-H005
Sony
Cisco C40, C60, C90,
SX80
EVI-HD3/VDI
EVI-HD7/DVI RC4-SHC RCC-C004/RCC-C005/RCC-C006 RCC-H001/RCC-H003/RCC-H004
Generic Controller
EVI-HD3/VDI
EVI-HD7/DVI
EVI-H100V
RC4-SHD RCC-C004/RCC-C005/RCC-C006
RCC-H001/RCC-H004/RCC-H010
Generic Controller SRG-120DH
SRG-300H RC4-SRG RCC-C001/RCC-C005/RCC-C006
RCC-H001/RCC-H004/RCC-H010
PCS-XG100S SRG-120DH RC4-X12 RCC-C001/RCC-C005/RCC-C006
RCC-H040
Starleaf
GT Mini 3330
GT 3351
GTm 5250
SRG-120DH RC4-SL1 RCC-C001/RCC-C005
RCC-H001/ RCC-H017

www.soundcontrol.net 203-854-5701 ©SOUND CONTROL TECHNOLOGIES, INC. 2017
To proceed with the installation, insure that you have installed one CAT5e or CAT6 cable between the
camera installation site and the codec installation site.
Minimum distance should be approximately 30’/9M.
The cable must be wired for either UTP 568A or UTP 568B. Please use the following scheme:
To install the RemoteCam4™ Kit, follow this step-by-step guide:
•Step 1
•Test and verify the Cat5e or Cat6 cable for UTP 568A or 568B wiring.
•Step 2
•Install the RC4-HE Head-End Module at the rack/equipment location.
•Connect the Cat5e or Cat6 cable to the RJ45 connector labelled on the RC4-HE module.
•Connect the power supply to the RC4-HE Module.
•Wait to connect the cable to the RC4-CE until steps 3 & 4 are completed.
•Step 3
At the camera location connect the PowerSniffer™ to the CAT5e or CAT6 cable.
If the cable is properly terminated it will display 8 green LEDs. See Image at left.
Any other result, please re-terminate.
•
Step 4
•
Disconnect the power supply from the RC4-HE
•Step 5
•
Connect the CAT5e or CAT6 cable to the RJ45 connector labelled on the RC4-CE Camera Module.
•Step 6
•
Connect provided cables between codec and RC4-HE module.
•Step 7
•Connect provided cables between camera and RC4-CE module.
•Visca
•The Visca loop, or daisy chain, supports up to seven cameras. On supported applications SCT supplies a
Visca Out cable. This cable should be connected from the camera to the RC4-CE only when there is a
proceeding camera in the daisy chain. Utilizing this cable on the last camera in the chain will terminate
control of all cameras.
•Step 8
•Connect the power supply to the RC4-HE module
•LED Behavior:
•Head-End Module HDCP LED: Blinking = HDCP Inactive, Solid = HDCP Active
•Head-End Module LED: Blinking Red = No Link, Blinking Red to Green = Active
•
Camera Module: LED will be Red until Link is established, Solid Green when is Active
•Step 9
•
Enjoy!
LINK
LINK
LINK
LINK
LINK
LINK
LINK
LINK
LINK