Rife EF003 User manual

English
1
Installation Instruction
UNPACKING INSTRUCTIONS
IMPORTANT SAFETY INFORMATION
             
   
              
           
      
            
           

            
          
                
             
         

2
Supplied Parts List
22
      
  
     
 

     
 
 
   
 
  

3
Step 1 Install the Pole to the Desktop
1. Install the Pole(a) to the Weighted
Base(b) using 3pcs M5x14 Bolts(g),
and tighten using the Allen Key(o), see
Figure 1.
2. Optionally, you can drill a 10mm
diameter hole in your desk and secure
using the Support Plate (j), M10
Washer(k), Spring Washer(l) and M10
Bolt(i). Fasten the M10 Bolt with
provided Wrench(p), see Figure 2.
Option A: Weighted Base Install
j
i
k
l
a
m
g
Figure 3
Figure 5
Option B: Grommet Base Install
If the existing grommet hole comes with a
plastic protector, remove it to ensure a flat
surface before installing the desk mount.
1. Install the Grommet Base Plate(m) to the
Pole(a) using 3pcs M5x14 Bolts(g), and
tighten using the Allen Key(o), see Figure 3.
2. Attach Soft Pad(t) to the Grommet Base
Plate(m), see Figure 4.
3. Position the Pole(a) on the mounting
surface and secure using the Support Plate
(j), M10 Washer(k), Spring Washer(l) and
M10 Bolt(i). Fasten the M10 Bolt using
provided Wrench(p), see Figure 5.
Existing Grommet Hole Installation
a
g
b
j
i
k
l
l
Figure 2
Figure 1
tFigure 4

Install the Pole to the Desktop
Install Arm to the Pole
Install Swivel Arm(c) to the Pole
(a). Fasten the bolt with supplied
Allen Key(o). Attach the Wire Clip
(n1,n2) to the Pole(a) and Swivel
Arm(c).
j
i
k
l
m
a
g
Figure 6
Figure 8
Option C: Grommet Base Install
1. Position the Pole(a) on the mounting
surface and mark the center hole. Drill a 3/8"
(10mm) diameter hole at the marked
position through the mounting surface.
2. Install the Grommet Base Plate(m) to the
Pole(a) using 3pcs M5x14 Bolts(g), and
tighten using the Allen Key(o), see Figure 6.
3. Attach Soft Pad(t) to the Grommet Base
Plate(m), see Figure 7.
4.Position the Pole(a) on the mounting
surface and secure using the Support Plate
(j), M10 Washer(k), Spring Washer(l) and
M10 Bolt(i). Fasten the M10 Bolt using
provided Wrench(p), see Figure 8.
Self Drilled Grommet Hole Installation
4
Step 1
Step 2
tFigure 7
c
on1
n2

Attach the Side VESA Plates to the Monitors
5
s
r
q
d1
Step 3A
Attach the Center VESA Plate to the Monitor
Step 3B
For Monitor with Flat Back For Monitor with Curved or
Recessed Back
For Monitor with Flat Back For Monitor with Curved or
Recessed Back
d1
q
s
r
d2 d2

Slide the monitor onto the head of
Swivel Arm(c) as shown in the above
diagram.
Install the security Nut(e). Make sure
the security nut is installed before you
rotate the monitor.
Slide the monitor onto the head of
Monitor Arm(c) as shown in the above
diagram.
Install the M4x6 Bolt(f). Make sure the
bolt is installed before you rotate the
monitor.
6
e
f
c
c
Slide the Side Monitors onto the Head of Swivel Arm
Step 4A
Slide the Center Monitor onto the Head of Monitor Arm
Step 4B

Tighten the bolt with the supplied Allen
Key(o) to fix the tilt angle.
Fasten the grub screw in monitor arm to fix
the tilting angle by provided Allen Key(o).
Adjust the heigh of Centre Monitor: Turn
the bolt counterclockwise to lower the center
monitor, turn the bolt clockwise to raise the
center monitor.
Adjust the height of Side Monitors:
Remove the Nut(e) and turn the bolt
counter-clockwise with supplied Allen key(o)
to raise the monitor. Install the Nut(e) after
the adjustment.
7
o
o
grub
screw
o
Fix the Tilt Angle of Side and Center Monitors
Step 5
Adjust the Horizontal Level of Monitors
Step 6
Ignore this step if
monitors are level

8
n1
Manage the Wires
Step 7
Manage the wires and store the Allen keys(o) in Wire Clip(n1) for future use.
Thank you for choosing our products!