Sculpt Fireplaces Europa 7 Operation manual

1
1. SPECIFICATIONS
2. PRELIMINARY INSTALL GUIDE
3. COMPONENTS LIST
4.0 INBUILT AGAINST COMBUSTIBLE WALL
5. INBUILT INTO ISLAND WALL
NO COMBUSTIBLE SURROUNDINGS
6. EXISTING CHIMNEY INSTALL
7. FREE STANDING INSTALL
8. LIFT UP DOOR ASSEMBLY
9. OPERATION & MAINTENANCE
10. WARRANTY
Europa 7 |Super 9 | Visio 8 Plus
INSTALLATION & USER GUIDE
SEGUIN
NOTICE TO INSTALLER:
These instructions must be left with the owner, who should keep them for future use.
4.1 MASONRY BRICK INSTALLATION
4.2 HEBEL INSTALLATION
4.3 SKAMOL: REFER TO SKAMOTEC 225 MANUAL

2
COMPLIANCE PLATE AND SERIAL NUMBER.
The instructions in this manual are recommendations only, the distributor and manufacturer bears no liability to the interpretation of these instructions.

3
Thank you for choosing Sculpt Fireplaces as your heater of choice.
Your replace is the result of careful design, artisan engineering and safety tests.
If it is properly installed, used and maintained, you may be sure that you will have an outstanding
heating feature in your home for years to come.
We advise you to read through this guide in order to become acquainted with the installation
methods specic to your replace.
It is recommended that this replace must be installed by a qualied and licensed trades
professional. You will nd in this guide answers to most of your questions, you should also
contact your retailer for any further information.
Before igniting your replace for the rst time, please carefully read this manual.
Follow @sculptreplacecollection on Instagram or like SculptFireplaceCollection on Facebook
and post your latest masterpiece installed with the hashtag #sculptres
We hope we’ve helped make you the envy of your friends this winter and years to come.
From all of us,
Sculpt Fireplace Collection
CONGRATULATIONS!

4
IMPORTANT
*Heating capacity of the following appliances are a guide only and refers to areas with 2.4m ceilings
and 6 or more star rated buildings. Heating output may vary depending on factors such as building
characteristics, quality of insulation, type of rewood used and climate zone.
All dimensions shown are approximate. Check all dimensions accurately prior to installation. In line with
our policy of continuous improvement, we reserve the right to alter specications without notice.
All units comply and MUST be installed to Australian & New Zealand Standard AS/NZS 2918:2001.
When in use some parts may become hot. A suitable re guard is recommended where very young,
elderly or inrm are concerned.
ALL FIREPLACES IN THIS MANUAL CONFORM TO AUSTRALIAN AND NEW ZEALAND STANDARDS
AS/NZS 2918;2001 DOMESTIC SOLID FUEL BURNING APPLIANCES & AS/NZS 4012/4013(2014).
The instructions in this manual are recommendations only, the distributor and manufacturer bears no liability to the interpretation of these instructions.

5
1. SPECIFICATIONS
OPTIONAL
OUTDOOR AIRKIT
FITTING
OPTIONAL
OUTDOOR AIRKIT
FITTING
617mm
480mm
45mm
712mm
25mm
712mm
722mm
575mm
830mm
100mm
480mm
290mm
542mm
43mm
25mm
85mm 40mm
1220
mm
material
KW output
Heating capacity*
facace
glass door
minimum flue HeigHt
flue sizes
includes Hot air Kit
outside air Kit
Warranty
WeigHt
HeartH dimensions*
* for inbuilt models only
** Dimensions show include lift up door option, exclude these dimensions for swing door model
100% Pure cast iron, 8-12mm thickness
17.9kW
Up to 150-250m2
Clean frame-less design(trim options available)
Secure swing or lift up door opening system
4.5m
200mm, 250mm, 300mm
A duct and a register
Recommended for well insulated homes
10 year rebox warranty*
170kg
min 500mm in front of any part of replace, 250mm on either
side & 75mm thick*
SEGUIN EUROPA 7

6
1. SPECIFICATIONS
560mm
1235
mm
30 mm
89.6mm
305.6
mm
480mm
805
mm
480mm
531
mm
805 mm
695mm
531mm
823
mm
OPTIONAL
OUTDOOR AIR KIT
FITTING
OPTIONAL
OUTDOOR AIR KIT
FITTING
material
KW output
Heating capacity*
facace
glass door
minimum flue HeigHt
flue sizes
includes Hot air Kit
outside air Kit
Warranty
WeigHt
HeartH dimensions*
* for inbuilt models only
** Dimensions show include lift up door option, exclude these dimensions for swing door model
100% Pure cast iron, 8-12mm thickness
27.8kW
Up to 240-340m2
Clean frame-less design(trim options available)
Secure swing or lift up door opening system
4.5m
200mm, 250mm, 300mm
A duct and a register
Recommended for well insulated homes
10 year rebox warranty*
190kg
min 500mm in front of any part of replace, 250mm on either
side & 75mm thick*
SEGUIN VISIO 8

7
1. SPECIFICATIONS
OPTIONAL
OUTDOOR AIR KIT
FITTING
OPTIONAL
OUTDOOR AIR KIT
FITTING
467mm
450mm
75mm
978mm
550mm
663mm
785mm
911mm
485mm 450mm
500mm
1340mm
911mm
material
KW output
Heating capacity*
facade
glass door
minimum flue HeigHt
flue sizes
includes Hot air Kit
outside air Kit
Warranty
WeigHt
HeartH dimensions*
* for inbuilt models only
** Dimensions show include lift up door option, exclude these dimensions for swing door model
100% Pure cast iron, 8-12mm thickness
26.9kW
Up to 200-300m2
Clean frame-less design(trim options available)
Secure swing or lift up door opening system
4.5m
250mm, 300mm, 350mm
A duct and a register
Recommended for well insulated homes
10 year rebox warranty*
250kg
min 500mm in front of any part of replace, 250mm on either
side & 75mm thick*
SEGUIN SUPER 9

8
2. PRELIMINARY INSTALL GUIDE
It is the users duty to make themselves aware of and apply all national or more restrictive local
standards and instructions(AS/NZS 2918:2001).
IMPORTANT
Prior to unpacking and installation check that the appliance has not been damaged during transport.
Ensure you check the glass, the door(s), the damper operation and the door locking mechanism
Before any work is carried out, as per local and national regulations and laws, this appliance MUST be
installed by a licensed professional as per Australian and New Zealand Standards 2918:2001.
IMPORTANT WARNING
It is strictly forbidden to use any combustible materials (ie; wooden framing, plaster, etc) near or around
this appliance. Any exception from this rule is a health and safety hazard which will result in a non-
compliant installation and a void of warranties.
Electrical cables and components must not be placed in the vicinity of the appliance as it is a re
hazard.

9
For the installation and use of this appliance, the tter and the user should strictly adhere to local and
national regulations as well as Australian & New Zealand Standards AS/NZS 2918:2001. They should
also comply with the instructions and recommendations detailed in this manual. Safety and operation
of the replace is directly dependent thereon. The liability of the manufacturer can neither be retained
nor assured following failure of installation or incorrect use which does not comply with AS/NZS
2918:2001.
As each installation is a particular case, a qualied and licensed trades professional should take all
required preliminary precautions depending on the technical elements inherent to each job.
In-observance of the assembly instructions in conjunction with AS/NZS 2918:2001 entails the liability
of the person who carries it out.
As a result of faulty assembly, irrational use of parts or additional components that were not supplied
by the manufacturer, and/or modifying of the appliance or components will result in inferior or unsafe
operation. Should this occur the manufacturer bears no liability, and will result in a null and void product
warranty.
PRELIMINARY INSTALL INFORMATION
All images and diagrams in this manual are for installation reference purposes only and are not to
scale. The distributor and manufacturer bears no accuracy of these images and accepts no liability. The
purpose of these images and diagrams is to act as a guide in conjunction with the written components
and are NOT to instruct independently. The order of these steps are a recommendation only.
It is strongly recommended that the licensed trade professional who is performing the installation of
this appliance, completely read and understand all instructions in this manual prior to proceeding.
Sculpt Fireplaces & Seguin Duteriez reserves the right to change these specications without prior
notice.
PLEASE READ PRIOR TO INSTALL
For reasons of quality control, some of our appliances are delivered assembled. Some lighter units
are directly assembled, puttied and sealed. Whilst other heavier models are delivered with the gather
unassembled to make it easier for transportation. Gasket and refractory putty is provided with these
units, a slip is placed in all the non-jointed replace in order to attract attention. Assemble the gather
on the top of the rebox, the putty should be widely spread and then wiped.
ACCEPTABLE VARIANCE ALLOWANCE
Due to the production of these hand assembled and manufactured replaces, there is an acceptable allowance
of 3-5mm variance of the unit, including the door frame. This variance in production is non-claimable under any
warranties.
HEAT RESISTANT MATERIALS
Heat resistant materials must meet AS/NZS 2918:2001 clause 1:5.21 a material with an allowable service
temperature of 600° Celsius or greater.
2. PRELIMINARY INSTALL GUIDE

10

11
FRESH AIR INLET, RECOMMENDED FOR ALL INSTALLATIONS
The air inlet is recommended for installation and is essential for the proper function of the appliance. The fresh
combustion air inlet must be a minimum 300mm2 and ideally positioned (see point A & B on diagram).
PLEASE READ PRIOR TO INSTALL
Clearance Gap 50mm
Firebox
Non combustible wall
Hot air grid
Air vents
False Ceiling
A

B
2. PRELIMINARY INSTALL GUIDE

12
3. COMPONENTS LIST
900MM STAINLESS FLUE - 200MM DIAMETER
900MM GALVANISED FLUE - 250MM DIAMETER
900MM GALVANISED FLUE - 300MM DIAMETER
WIND RIM COWL TO SUIT
900MM STAINLESS FLUE - 250MM DIAMETER
900MM GALVANISED FLUE - 300MM DIAMETER
900MM GALVANISED FLUE - 350MM DIAMETER
WIND RIM COWL TO SUIT
900MM STAINLESS FLUE - 200MM DIAMETER
900MM GALVANISED FLUE - 300MM DIAMETER
WIND RIM COWL TO SUIT
5
4
4
1
5
4
4
1
5
1
1
4.5M INBUILT TRIPLE SKIN FLUE KIT - SEGUIN EUROPA 7 & VISIO 8
IMPORTANT
This components list details the number of flue supplied(by the retailer) according to unit and minimum
flue kit requirements. For correct use please ensure you are referring to your unit model and installation
kit type. For any questions in relation to the supplied components contact your local retailer. Each unit is
supplied with a ducting kit consisting of; one metal register and one duct( 4 Zero Type: aluminium inner
core, aluminium outer, poly insulated, minimum RI.0) by the retailer.
COMPONENTS
COMPONENTS
COMPONENTS
QUANTITY
QUANTITY
QUANTITY
4.5M INBUILT TRIPLE SKIN FLUE KIT - SEGUIN SUPER 9
4.5M INBUILT CHIMNEY FLUE KIT - SEGUIN EUROPA 7 & VISIO 8 PLUS

13
3. COMPONENTS LIST
900MM STAINLESS FLUE - 250MM DIAMETER
900MM GALVANISED FLUE - 300MM DIAMETER
WIND RIM OPTION B COWL TO SUIT
900MM STAINLESS FLUE - 200MM DIAMETER
900MM BLACK GALVANISED FLUE - 250MM DIAMETER
900MM GALVANISED FLUE - 250MM DIAMETER
900MM GALVANISED FLUE - 300MM DIAMETER
BLACK DROPPER BOX AND CEILING RING TO SUIT
WIND RIM OPTION B COWL
5
1
5
3*
2
2
1
1
Sculpt Fireplace Collection bears no liability to the functioning and supply of these components.
Additional components required for installation are the responsibly of the retailer and(or) installer.
*Double skin black flue to be dependant on ceiling height, ascertained by the retailer.
COMPONENTS
COMPONENTS
QUANTITY
QUANTITY
4.5M FREESTANDING BLACK FLUE KIT - SEGUIN EUROPA 7 & VISIO 8 PLUS
4.5M INBUILT CHIMNEY FLUE KIT - SEGUIN SUPER 9
900MM STAINLESS FLUE - 200MM DIAMETER
900MM BLACK GALVANISED FLUE - 250MM DIAMETER
900MM GALVANISED FLUE - 250MM DIAMETER
900MM GALVANISED FLUE - 300MM DIAMETER
BLACK DROPPER BOX AND CEILING RING TO SUIT
WIND RIM OPTION B COWL
5
3*
2
2
1
1
COMPONENTSQUANTITY
4.5M FREE STANDING BLACK FLUE KIT - SEGUIN SUPER 9

14
4.1 MASONRY BRICK INSTALLATION
STEP 1: BASE
Lay a masonry base, minimum 75mm thick (ie. solid bricks).
The base should be laid on a adequate ground supporting it’s
weight.
**IMPORTANT**
If using the optional Outdoor Air Kit please leave a 125mm air
gap behind the rebox. Refer to Step 6: Outdoor Air Kit.
STEP 2: BACK WALL
Using masonry brick, construct the back wall from the base to
the top of the ceiling.
STEP 3: SHEET METAL LAYER (OPTIONAL STEP)
Place a thin piece of sheet metal on top of the bricks in order to
level the base and safely manoeuvre the rebox.
Allow a minimum of 100mm on all sides.

15
STEP 4: POSITIONING OF THE UNIT
Place the rebox into position on top of the sheet metal.
Remember to leave a 25mm air gap on all sides of the rebox.
(If an outdoor air-kit is to be connected please leave a 125mm
air-gap at the rear of the rebox).
4.1 MASONRY BRICK INSTALLATION
STEP 6: OUTDOOR AIR KIT(IF NOT REQUIRED GO TO STEP 7)
Any depression or lack of fresh air within the room where the
replace is located can cause emanation of smoke to flow
back into the room and the unit to run inefciently. It is highly
recommended that an Outdoor Air Kit be installed in six or more
star rated homes, or any install where a mechanical device (ie.
fan), takes air from the replace cavity & transfers it.
Place the adaptor on the back of the unit and screw into
position. Attach the flexi flue to the adaptor and run to the
external brick wall at the rear of the unit, then proceed to
connect the metal vermin proof cowl onto the outside wall.
The flexi flue can be positioned either side of the adaptor in
order to t between the heater and the wall. It is not required
that the flexi flue be positioned directly behind the rebox.
STEP 5: LIFT UP DOOR ASSEMBLY (IF NOT REQUIRED GO TO STEP 6)
**IMPORTANT**
Refer to images on page 37. LIFT UP DOOR ASSEMBLY.
Three bolts mount the lift up door mechanism. It is
recommended that you use two solid pieces of timber
approximately 450mm long in order to assist in the assembly
of the door.
1. Lift the door into position and place door lift mechanism in
position above replace door.
2. Lift ballast and place timbers in-between guillotine
movement of slider to prevent ballast from coming back
down.
3. Fix the 3 silver bolts into the heater frame through the
ballast frame
4. Release weight from the wood when mechanism is secure
in place.
5. Lift ballast and secure chains through sprocket onto the
small bolts attached to door (make sure spacers for chain
are inserted into link attached to door)
6. Release weight from the wood when chain is secured on
both sides of door.
Door should now lift and lower with ease, please test this
before continuing.

16
STEP 8: FIRST LENGTH OF FLUE
Place the rst single skin length of flue (with no crimp ends)
around the outside of the spigot. You may also use a heat
resistance sealant(i.e.Firecork) to seal any air gaps. Before
installing the remaining lengths of flue please go to the next
step.
STEP 9: SIDE WALLS & VENTILATION
**IMPORTANT**
Ventilation is required on the enclosure to help with air
circulation. A minimum of two air intake grills are required
at the bottom and a minimum of two air out-take grills are
required on top of the masonry enclosure (2X inflow 2X
outflow). All vents can be positioned either side OR the front of
the masonry enclosure. ALL vents must adhere to the minimum
vent size of size 300mm2.
Using masonry(ie. clay bricks) build a layer of bricks from
the base to the top of the ceiling on either side of the rebox.
Remember to leave a minimum 25mm air gap on all edges.
*The vent sizes and quantity can be adapted and changed
BUT they must meet the minimum ventilation requirements
as specied above. For custom made vents please contact
your nearest dealer. ALL VENTS MUST NOT BE PLASTIC OR
COMBUSTIBLE.
STEP 7: LAYLA 3 TRIM WITH LIFT DOOR(IF NOT REQUIRED GO TO
STEP 8)
**IMPORTANT**
Trim must be tted onto the rebox PRIOR to installing the
front of the masonry enclosure.
1. Put the trim on the front of the rebox
2. On the side of the façade of the rebox drill two holes at
4.2mm
3. The holes must match with the slotted holes on the trim
4. Put the trim into place
5. Fix the trim with the screws provided (screws M5 +
washers)
LAYLA 3 TRIM WITH NO LIFT DOOR (IF NOT REQUIRED GO TO STEP 8)
If the trim is to be assembled to t onto a rebox not equipped
with a lift up door, you will need to weld the bracket (width
5 mm each). The brackets (2x5 mm) are necessary to
compensate the initial width of the trim.
4.1 MASONRY BRICK INSTALLATION
*All air vents must have a minimum clearance to combustibles
of 600mm in front and 300mm above the metal vent itself.

17
FAN MUST BE METAL NOT PLASTIC
STEP 11: DUCTING
The duct MUST be 4 Zero type(aluminium inner core,
aluminium outer, poly insulated, minimum RI.0) and tested to
AS 4254.1-2012. Outlet MUST be metal.
This unit has been supplied with a ducting kit by the retailer
(consisting of one duct and one metal register), while it is
highly recommended that it be installed, if not installed it will
have no implication on the functioning of the unit.
Cut a hole in the lid of the enclosure nearest to the room where
the heat is to be transferred. Run the ducting from this hole into
the roof space and locate to the room, cut out the plaster and
install a metal register into the ceiling of the next room.
**PLEASE NOTE: A maximum duct run of 6m is recommended,
no more than two ducts should run off this cavity.
If an in-line fan is tted to the ducting kit, then an Outdoor Air
Kit is obligatory and MUST be installed to the unit. All ducting
STEP 12: FLUE INSTALLATION
Triple skin flue is to then be continued on top of the cavity lid.
The lower end of the triple skin casing shall be close tting
against the lid and the outer casing must be ventilated. Air
vents on the rst length of triple skin flue must be cut (please
use diagram as a guide), or manufactured into the bottom
length of the flue.
300mm
BELOW
CEILING
15°
CAVITY LID
TO BE FULLY
SEALED TO
ALL EDGES.
4.1 MASONRY BRICK INSTALLATION
STEP 10: CAVITY LID
**IMPORTANT**
SIDE VENTS
It is highly recommended the cavity lid be installed flat to
ensure sufcient air flow around the appliance if 2 vents are
used.
FRONT VENTS
It is highly recommended the cavity lid be installed on an angle
of 15° facing the front of the replace to ensure sufcient air
flow around the appliance.
The cavity lid must be installed 300mm below the ceiling and
is comprised of the following; minimum 0.5mm thick steel
plate for support, followed by a 12mm thick heat resistant
sheet, with 1 x 25mm Rockwool sheet. A hole is to be cut in
the centre of the lid in order for the single skin flue to penetrate
through tightly. You may also use a heat resistance sealant(i.e.
Firecork)and heat proof tape to seal the any air gaps. Please
ensure the cavity lid is fully sealed to all edges.

18
STEP 14: HEARTH (FLOOR PROTECTOR)
The hearth must be constructed from masonry or a non
combustible material and must extend 500mm in front of the
appliance, 250mm on either side of the appliance and have a
thickness of 75mm.
STEP 13: FLUE INSTALLATION
The triple skin flue will then be continued into the roof cavity
and above the roof line, as per Australian & New Zealand
Standard AS/NZ 2918:2001. There must be a 25mm clearance
around the outer triple skin flue. The flue must extend a
minimum 1m above the roof line and have a 3m clearance from
any combustibles in a horizontal direction.
**IMPORTANT**
The flue should not include more than two 45°degree bends.
The angle of these bends cannot exceed more than 45°and can
have no more than one length of 900mm flue between them.
STEP 13: FRONT OF THE ENCLOSURE
The front of the enclosure can now be tted with masonry
bricks or a layer of 12mm minimum thick heat resistant sheet.
Remember to keep an air gap of 25mm from the front of the
unit.
4.1 MASONRY BRICK INSTALLATION

19
STEP 17: BAFFLE PLATE
Ensuring the wider end of the baffle plate is facing the inside
back wall of the rebox, and the flat surfaces are positioned
downwards, proceed to gently position the plate on the lugs
located on the inside ceiling of the rebox. Once in position
ensure the plate sits securely, the baffle plate should not rock
or shift when touched if placed correctly.
4.1 MASONRY BRICK INSTALLATION

20
STEP 2: BACK WALL & METAL SHEET(OPTIONAL STEP)
Using Hebel, build the back wall from the base to the top of the
ceiling.
Place a thin piece of sheet metal on top of the bricks in order to
level the base and safely manoeuvre the rebox.
Allow a minimum of 100mm on all sides.
STEP 3: SIDE WALLS - FIRST LAYER
Place a steel frame (minimum 51mm thick) on either side of
the enclosure. Remember to leave a 50mm air gap on the sides
of the appliance.
**IMPORTANT**
It is strongly recommended that the steel frame allows for a
distance of 300mm to the ceiling, this allows the cavity lid to
be placed directly above and stop heat from traveling above the
lid via the frame.
4.2 HEBEL INSTALLATION LIGHT WEIGHT INSTALLATION
STEP 1: BASE
Lay a masonry base of Hebel blocks, minimum 75mm thick.
The base should be laid on a adequate ground supporting it’s
weight.
**IMPORTANT**
If using the optional Outdoor Air Kit please leave a 125mm air
gap behind the rebox. Refer to Step 6: Outdoor Air Kit.