Sculpt Fireplaces H1200/DS Operation manual

1
1. SPECIFICATIONS
2. PRELIMINARY INSTALL GUIDE
3. OUTDOOR AIR KIT
4. COMPONENTS LIST
5.0 INBUILT AGAINST COMBUSTIBLE WALL
6. INBUILT INTO ISLAND WALL
NO COMBUSTIBLE SURROUNDINGS
7. OPERATION & MAINTENANCE
8. WARRANTY
H1200/DS | H1400 | H1600/DS | H1600XXL/DS
H1200VLG/D | H12003V | epi950
INSTALLATION & USER GUIDE
AXIS
NOTICE TO INSTALLER:
These instructions must be left with the owner, who should keep them for future use.
5.1 MASONRY BRICK INSTALLATION
5.2 HEBEL INSTALLATION
5.3 SKAMOL: REFER TO SKAMOTEC 225 MANUAL

2
COMPLIANCE PLATE AND SERIAL NUMBER.
The instructions in this manual are recommendations only, the distributor and manufacturer bears no liability to the interpretation of these instructions.

3
Thank you for choosing Sculpt Fireplaces as your heater of choice.
Your replace is the result of careful design, artisan engineering and safety tests.
If it is properly installed, used and maintained, you may be sure that you will have an outstanding
heating feature in your home for years to come.
We advise you to read through this guide in order to become acquainted with the installation
methods specic to your replace.
It is recommended that this replace must be installed by a qualied and licensed trades
professional. You will nd in this guide answers to most of your questions, you should also
contact your retailer for any further information.
Before igniting your replace for the rst time, please carefully read this manual.
Follow @sculptreplacecollection on Instagram or like SculptFireplaceCollection on Facebook
and post your latest masterpiece installed with the hashtag #sculptres
We hope we’ve helped make you the envy of your friends this winter and years to come.
From all of us,
Sculpt Fireplace Collection
CONGRATULATIONS!

4
IMPORTANT
*Heating capacity of the following appliances are a guide only and refers to areas with 2.4m ceilings
and 6 or more star rated buildings. Heating output may vary depending on factors such as building
characteristics, quality of insulation, type of rewood used and climate zone.
All dimensions shown are approximate. Check all dimensions accurately prior to installation. In line with
our policy of continuous improvement, we reserve the right to alter specications without notice.
All units comply and MUST be installed to Australian & New Zealand Standard AS/NZS 2918:2001.
When in use some parts may become hot. A suitable re guard is recommended where very young,
elderly or inrm are concerned.
ALL FIREPLACES IN THIS MANUAL CONFORM TO AUSTRALIAN AND NEW ZEALAND STANDARDS
AS/NZS 2918;2001 DOMESTIC SOLID FUEL BURNING APPLIANCES & AS/NZS 4012/4013(2014).
The instructions in this manual are recommendations only, the distributor and manufacturer bears no liability to the interpretation of these instructions.

5

6
1. SPECIFICATIONS
material
KW output
Heating capacity*
facace
glass door
minimum flue HeigHt
flue sizes
includes Hot air Kit
outside air Kit
Warranty
WeigHt
legs**
HeartH dimensions*
Solid steel rebox with 60mm thick re bricks
30kW
Up to 200m2
Clean frame-less design(trim options available)
Secure swing & lift door
5.4m
250mm, 300mm, 350mm
Two ducts and two registers
Recommended for well insulated homes
10 year rebox & re brick warranty*
380kg
Adjustable 180mm-600mm
min 500mm in front of any part of replace, 250mm on either
side & 75mm thick*
AXIS H1200
923MM
500MM
535MM
1204MM
1502MM
1351MM
900MM
180MM**
171MM
535MM 618MM
574MM
254MM
691MM

7
1. SPECIFICATIONS
material
KW output
Heating capacity*
facace
glass door
minimum flue HeigHt
flue sizes
includes Hot air Kit
outside air Kit
Warranty
WeigHt
legs**
HeartH dimensions*
Solid steel rebox with 60mm thick re bricks
30kW
Up to 200m2
Clean frame-less design(trim options available)
Secure swing & lift door
5.4m
250mm, 300mm, 350mm
Two ducts and two registers
Recommended for well insulated homes
10 year rebox & re brick warranty*
380kg
Adjustable 180mm-600mm
min 500mm in front of any part of replace, 250mm on either
side & 75mm thick*
AXIS H1200DS
923MM
1148.5MM
500MM
535MM
1205MM
1474MM
1323MM
900MM
180MM**
171MM
535MM 591MM
997MM
321MM 321MM
574MM
683MM

8
1. SPECIFICATIONS
material
KW output
Heating capacity*
facace
glass door
minimum flue HeigHt
flue sizes
includes Hot air Kit
outside air Kit
Warranty
WeigHt
legs**
HeartH dimensions*
Solid steel rebox with 60mm thick re bricks
32.5kW
Up to 280-320m2
Clean frame-less design(trim options available)
Secure swing & lift door
5.4m
300mm, 350mm, 400mm
Two ducts and two registers
Recommended for well insulated homes
10 year rebox & re brick warranty*
400kg
Adjustable 180mm-600mm
min 500mm in front of any part of replace, 250mm on either
side & 75mm thick*
AXIS H1400
1353MM
1597MM
1108MM
1035MM
624MM
485MM
582MM
690MM
1402MM
674MM
742MM
278MM
180MM**
170MM
582MM 665MM

9
1586MM
786MM
658MM
555MM
491MM
612MM
302MM
612MM
1330MM
1300MM
491MM
450MM
180MM**
1396MM
170MM
1. SPECIFICATIONS
material
KW output
Heating capacity*
facace
glass door
minimum flue HeigHt
flue sizes
includes Hot air Kit
outside air Kit
Warranty
WeigHt
legs**
HeartH dimensions*
Solid steel rebox with 60mm thick re bricks
35kW
Up to 300-350m2
Clean frame-less design(trim options available)
Secure swing & lift door
5.4m
300mm, 350mm, 400mm
Two ducts and two registers
Recommended for well insulated homes
10 year rebox & re brick warranty*
460kg
Adjustable 180mm-600mm
min 500mm in front of any part of replace, 250mm on either
side & 75mm thick*
AXIS H1600

10
1. SPECIFICATIONS
material
KW output
Heating capacity*
facace
glass door
minimum flue HeigHt
flue sizes
includes Hot air Kit
outside air Kit
Warranty
WeigHt
legs**
HeartH dimensions*
Solid steel rebox with 60mm thick re bricks
25kW
Up to 250m2
Clean frame-less design(trim options available)
Secure swing & lift door
5.4m
300mm, 350mm, 400mm
Two ducts and two registers
Recommended for well insulated homes
10 year rebox & re brick warranty*
460kg
Adjustable 180mm-600mm
min 500mm in front of any part of replace, 250mm on either
side & 75mm thick*
AXIS H1600DS
1300MM
1330MM
491MM
110MM
1586MM
180MM**
170MM**
661MM
555MM491MM
620MM
548MM
481MM
450MM

11
1. SPECIFICATIONS
material
KW output
Heating capacity*
facace
glass door
minimum flue HeigHt
flue sizes
includes Hot air Kit
outside air Kit
Warranty
WeigHt
legs**
HeartH dimensions*
Solid steel rebox with 60mm thick re bricks
40kW+
Up to 350-400m2
Clean frame-less design(trim options available)
Secure swing & lift door
5.4m
300mm, 350mm, 400mm
Two ducts and two registers
Recommended for well insulated homes
10 year rebox & re brick warranty*
530kg
Adjustable 180mm-600mm
min 500mm in front of any part of replace, 250mm on either
side & 75mm thick*
AXIS H1600XXL
1700MM
450MM
504MM 504MM
579MM
1720MM
1319MM
1428MM
1936MM
670MM
968MM
302MM
624MM
1986MM
1448MM
180MM**
200MM

12
1. SPECIFICATIONS
material
KW output
Heating capacity*
facace
glass door
minimum flue HeigHt
flue sizes
includes Hot air Kit
outside air Kit
Warranty
WeigHt
legs**
HeartH dimensions*
Solid steel rebox with 60mm thick re bricks
30kW
Up to 300m2
Clean frame-less design(trim options available)
Secure swing & swing door
5.4m
300mm, 350mm, 400mm
Two ducts and two registers
Recommended for well insulated homes
10 year rebox & re brick warranty*
530kg
Adjustable 180mm-600mm
min 500mm in front of any part of replace, 250mm on either
side & 75mm thick*
AXIS H1600XXL DS
1700MM
450MM
504MM
504MM 579MM
1712MM
1319MM
1428MM
1936MM
685MM 644MM
1986MM
1448MM
180MM**
200MM

13
material
KW output
Heating capacity*
facace
glass door
minimum flue HeigHt
flue sizes
includes Hot air Kit
outside air Kit
Warranty
WeigHt
legs**
HeartH dimensions*
Solid steel rebox with 60mm thick re bricks
20kW
Up to 200m2
Clean frame-less design(trim options available)
Secure swing & lift door
5.4m
250mm, 300mm, 350mm
Two ducts and two registers
Recommended for well insulated homes
10 year rebox & re brick warranty*
380kg
Adjustable 180mm-600mm
min 500mm in front of any part of replace, 250mm on either
side & 75mm thick*
AXIS H1200 3V
325MM
708MM
509MM
615MM
479MM
1019MM
1066MM
1481MM
632MM499MM
173MM
180MM**
685MM
543MM
940MM
940MM
855MM
640MM
1. SPECIFICATIONS

14
material
KW output
Heating capacity*
facace
glass door
minimum flue HeigHt
flue sizes
includes Hot air Kit
outside air Kit
Warranty
WeigHt
legs**
HeartH dimensions*
Solid steel rebox with 60mm thick re bricks
20kW
Up to 150-200m2
Clean frame-less design(trim options available)
Secure swing & lift door
5.4m
280mm, 330mm, 380mm
Two ducts and two registers
Recommended for well insulated homes
10 year rebox & re brick warranty*
330kg
Adjustable 180mm-600mm
min 500mm in front of any part of replace, 250mm on either
side & 75mm thick*
AXIS EPI 950
1034MM
334MM
718MM
800MM
800MM
563MM
670MM
638MM
563MM
1010MM
530MM
565MM
170MM
180MM**
592MM 843MM
1010MM
670MM
546MM
1. SPECIFICATIONS

15
material
KW output
Heating capacity*
facade
glass door
minimum flue HeigHt
flue sizes
includes Hot air Kit
outside air Kit
Warranty
WeigHt
legs**
HeartH dimensions*
Solid steel rebox with 60mm thick re bricks
20kW
Up to 200m2
Clean frame-less design(trim options available)
Secure swing & lift door
5.4m
250mm, 300mm, 350mm
Two ducts and two registers
Recommended for well insulated homes
10 year rebox & re brick warranty*
380kg
Adjustable 180mm-600mm
min 500mm in front of any part of replace, 250mm on either
side & 75mm thick*
AXIS H1200 VLG/D
1082MM
1106MM
1082MM
558MM
262MM
667MM
918MM
475MM
548MM473MM
517MM
1448MM
642MM
180MM**
167MM
128MM 128MM

16
2. PRELIMINARY INSTALL GUIDE
For the installation and use of this appliance, the tter and the user should strictly adhere to local and
national regulations as well as Australian & New Zealand Standards AS/NZS 2918:2001. They should
also comply with the instructions and recommendations detailed in this manual. Safety and operation
of the replace is directly dependent thereon. The liability of the manufacturer can neither be retained
nor assured following failure of installation or incorrect use which does not comply with AS/NZS
2918:2001.
As each installation is a particular case, a qualied and licensed trades professional should take all
required preliminary precautions depending on the technical elements inherent to each job.
In-observance of the assembly instructions in conjunction with AS/NZS 2918:2001 entails the liability
of the person who carries it out.
As a result of faulty assembly, irrational use of parts or additional components that were not supplied
by the manufacturer/distributor, and/or modifying of the appliance or components will result in inferior
or unsafe operation. Should this occur the manufacturer/distributor bears no liability, and will result in a
null and void product warranty.
PRELIMINARY INSTALL INFORMATION
All images and diagrams in this manual are for installation reference purposes only and are not to
scale. The distributor and manufacturer bears no accuracy of these images and accepts no liability. The
purpose of these images and diagrams is to act as a guide in conjunction with the written components
and are NOT to instruct independently. The order of these steps are a recommendation only.
It is strongly recommended that the licensed trade professional who is performing the installation of
this appliance, completely read and understand all instructions in this manual prior to proceeding.
Sculpt Fireplaces & Axis reserves the right to change these specications without prior notice.
For reasons of quality control, some of our appliances are delivered assembled. Parts including legs and
baffle plate may need to be installed on site.
EXPOSURE TO ELEMENTS
Axis replaces are exclusively designed as indoor heating appliances, should the replace (or part there of) be in
contact with the outside elements including rain, snow, direct sunlight, excessive winds, etc. Then the damage
sustained thereon will not be covered under the manufacturer or distributor warrantie(s). Please consider prior to
installing your replace exposed to outside elements.
ACCEPTABLE VARIANCE ALLOWANCE
Due to the production of these hand assembled and manufactured replaces, there is an acceptable allowance
of 3-5mm variance of the unit, including the door frame. This variance in production is non-claimable under any
warranties.
HEAT RESISTANT MATERIALS
Heat resistant materials must meet AS/NZS 2918:2001 clause 1:5.21 a material with an allowable service
temperature of 600° Celsius or greater. Gyprock Fyrecheck is NOT a recommended heat resistant material.
PLEASE READ PRIOR TO INSTALL

17
2. PRELIMINARY INSTALL GUIDE
It is the users duty to make themselves aware of and apply all national or more restrictive local
standards and regulations (AS/NZS 2918:2001).
IMPORTANT
Prior to unpacking and installation check that the appliance has not been damaged during transport.
Ensure you check the glass, the door(s), the damper operation and the door locking mechanism
Before any work is carried out, as per local and national regulations and laws, this appliance MUST be
installed by a licensed professional as per Australian and New Zealand Standards 2918:2001.
IMPORTANT WARNING
It is strictly forbidden to use any combustible materials (ie; wooden framing, plaster, etc) near or around
this appliance. Any exception from this rule is a health and safety hazard which will result in a non-
compliant installation and a void of warranties.
Electrical cables and components must not be placed in the vicinity of the appliance as it is a re
hazard.

18
2. PRELIMINARY INSTALL GUIDE
FRESH AIR INLET, RECOMMENDED FOR ALL INSTALLATIONS
The air inlet is recommended for installation and is essential for the proper function of the appliance. The fresh
combustion air inlet must be a minimum 300mm2 and ideally positioned (see point A & B on diagram).
PLEASE READ PRIOR TO INSTALL
Clearance Gap 50mm
Firebox
Non combustible wall
Hot air grid
Air vents
False Ceiling
A

B

19
LEG ASSEMBLY
Before beginning any work, we remind you to check the resistance and stability of the floor where the appliance is
to be installed. Installing the legs will allow you to raise the appliance by a total of 600mm.
To streamline the installation we advise you to assemble the feet sets prior to beginning the leg assembly. Each set
includes a flat angle bracket and a standard flat angle bracket, please check these components before proceeding
with assembly.
PLEASE READ PRIOR TO INSTALL
2. PRELIMINARY INSTALL GUIDE
A B
DIAGRAM A
We advise you to cross the nuts and bolts
in order to ensure a better bearing (refer to
diagram A)
DIAGRAM B
The standard bracket has a space without
hole which has to be turned towards the top
(refer to diagram B)

20
OPENING LOWER VENTS - REQUIRED IF APPLIANCE IS TO INSTALLED WITHOUT LEGS
If you plan on installing the unit excluding the legs you MUST open the ALL vents located at the bottom of the
appliance prior to installation, this will ensure sufcient air flow around the unit, failure to complete this step will
impact negatively on the functioning of the appliance.
To open the air vents simply apply a medium amount of pressure to the steel cover, the hatch should come free-
once completed these pieces can be discarded.
AIR VENTS OPEN
AIR VENTS CLOSED
PLEASE READ PRIOR TO INSTALL
2. PRELIMINARY INSTALL GUIDE