Seabreeze HIGH EFFICIENCY Series User manual

HIGH EFFICIENCY SERIES
OPERATION MANUAL
COOLING ONLY MODELS
SHE9A4ZIGX
SHE12A4ZIGX
SHE18A4ZIGX
SHE24A4ZIGX
HEAT PUMP MODELS
SHE9H4ZIGX
SHE12H4ZIGX
SHE18H4ZIGX
SHE24H4ZIGX
950-0194revC March 30, 2014

950-0194revC - 2 - March 30, 2014
TABLE OF CONTENTS
User Instructions ………………………………………………………………………………………
3
Parts Identification ……………………………………………………………………………………
4
Multi Zone Features …………………………………………………………………………………..
5
Multi Zone Operation …………………………………………………………………………………
6
Emergency Operation ………………………………………………………………………………..
6
Operation of Wireless Remote Control ……………………………………………………………
6
Display Icons ……………………………………………………………………………………………
6
Keypad Function ………………………………………………………………………………………
7
Remote Control Functions …………………………………………………………………………..
7
ON/OFF ……………………………………………………………………………………………
7
MODE …………………………………………………………………………………….............
7
SLEEP …………………………………………………………………………………………….
8
FAN ……………………………………………………………………………………….............
8
CLOCK ……………………………………………………………………………………………
8
TEMP ………………………………………………………………………………………………
8
PURGE …………………………………………………………………………………………….
8
TURBO …………………………………………………………………………………………….
8
+ / - ………………………………………………………………………………………………....
8
DISPLAY …..………………………………………………………………………………….
9
SWING ……..……………………………………………………………………………
9
FOLLOW ME ……………………………………………………………………………………
9
LOCK KEYPAD ……………………………………………………………………………………
9
SELECT º F or º C ………………………………………………………………………………...
9
Replacing Batteries ……………………………………………………………………………………
9
Optional Control –Wall Control…………………………………………………………………
10
Routine Care and Maintenance ……………………………………………………………………..
11
Cleaning Air Filters …………………………………………………………………………..............
11
Troubleshooting ……………………………………………………………………………………….
12
Error Codes ……………………………………………………………………………………………..
13
Technical Support –Warranty ……………………………………………………………...............
15
HIGH EFFICIENCY SERIES - SINGLE ZONE MODELS
Cool Only
SEER RATING
SHE9A4ZIGX
23 SEER
SHE12A4ZIGX
22 SEER
SHE18A4ZIGX
18 SEER
SHE24A4ZIGX
18 SEER
Heat Pump
SEER RATING
SHE9H4ZIGX
23 SEER
SHE12H4ZIGX
22 SEER
SHE18H4ZIGX
18 SEER
SHE24H4ZIGX
18 SEER
HIGH EFFICIENCY SERIES –DUAL, QUAD ZONE & FIVE PORT MODELS
Heat Pump
SEER RATING
SHE9H4ZIGX
16 SEER
SHE12H4ZIGX
16 SEER
SHE18H4ZIGX
16 SEER

950-0194revC - 3 - March 30, 2014
USER INSTRUCTIONS
In this manual, you will find information on safe operation of your new Multi Zone Mini Split. For
your safety and the safety of others, please read and understand this entire manual before
proceeding.
INSTALLATION
These units are not designed to be installed in the following locations:
Areas where there is a possibility of combustible gases or fumes.
Excessively damp or moist areas.
Direct exposure to sea wind (salt spray).
OPERATION
Always turn the unit off with the remote control. Never use a circuit breaker or fuse as a
means of turning the unit on or off, except in the case of an emergency.
Do not operate this unit if you are wet or have wet hands, electric shock can occur.
Do not spray insecticides, paints, or other flammable sprays or liquids into or around the unit.
Do not put foreign objects into the unit.
Do not hang or place items on the unit.
Do not use harsh chemicals such as paint thinner, benzene, or polish to clean the unit.
During cooling operation, shades, blinds, and curtains should be used to shade the room
from direct sunlight.
To the installer:
Explain operation and routine care to customer.
This manual should be given to the customer for future reference.
Do not dispose this product as unsorted municipal waste. Collection of such
waste for special treatment is necessary.

950-0194revC - 4 - March 30, 2014
PARTS IDENTIFICATION
Indoor Unit
Air In
Front Cover
Filter
Louvers
Air Out
Line-set
Collar
Binding
Tape
Remote
Control
Wiring and
Copper Tube
Drain
Tube
COOL
HEAT
FAN
DRY
TEMPERATURE
CLOCK ON
FAN
FOLL OW
ME
OFF
TURBO SLEEP DISPLAY
FAN
F
C
SWING
/ BLO W TEMP

950-0194revC - 5 - March 30, 2014
MULTI-ZONE FEATURES
Variable speed inverter type compressors for increased efficiency and quiet operation.
Automatic swing of vertical louvers for improved air flow (up/down).
Manual adjustment of horizontal louvers to set air flow direction (left/right).
Wireless remote control unit.
Comfortable temperature range of 61 ºF to 86 ºF in Cool/Dry/Heat/Fan modes.
TURBO fan mode in Heat and Cool modes for maximum air flow.
Timer mode for automatic starting and/or stopping for a preset period.
SLEEP mode for quiet energy saving operation during sleep periods.
Individual temperature selection for each zone.
Low ambient control.
Auto reset.
Purge –Reduces mold/mildew
Selectable ambient sensor location (indoor unit or remote control)
The Multi-Zone has many sizing options with various types of indoor units:
18K BTU - Dual Zone Configurations
30K BTU - Quad Zone Configurations
42K BTU - Quad Zone Configurations
1 INDOOR UNIT
2 INDOOR UNITS
9K
9K + 9K
12K
9K + 12K
2 INDOOR UNITS
3 INDOOR UNITS
4 INDOOR UNITS
9K + 9K
9K + 12K
9K + 18K
12K + 12K
12K + 18K
18K + 18K
9K + 9K + 9K
9K + 9K + 12K
9K + 9K + 18K
9K + 12K + 12K
12K + 12K + 12K
9K + 9K + 9K + 9K
The system matches below are not recommended if all indoor units may require simultaneous continuous duty at full efficiency.
9K + 12K + 18K
12K + 12K + 18K
9K + 9K + 9K + 12K
9K + 9K + 12K + 12K
2 INDOOR UNITS
3 INDOOR UNITS
4 INDOOR UNITS
5 INDOOR UNITS
9K + 9K
9K + 12K
9K + 18K
12K + 12K
12K + 18K
18K + 18K
9K + 9K + 9K
9K + 9K + 12K
9K + 9K + 18K
9K + 12K + 12K
9K + 12K + 18K
9K + 18K + 18K
12K + 12K + 12K
12K + 12K + 18K
9K + 9K + 9K + 9K
9K + 9K + 9K + 12K
9K + 9K + 9K + 18K
9K + 9K + 12K + 12K
9K + 9K + 12K + 18K
9K + 12K + 12K + 12K
9K + 9K + 9K + 9K + 9K
9K + 9K + 9K + 9K + 12K
The system matches below are not recommended if all indoor units may require simultaneous continuous duty at full efficiency.
12K + 18K + 18K
18K + 18K + 18K
9K + 9K + 18K + 18K
12K + 12K + 12K + 12K
12K + 12K + 12K + 18K
9K + 9K + 9K + 9K + 18K
9K + 9K + 9K + 12K + 12K
9K + 9K + 12K + 12K + 12K

950-0194revC - 6 - March 30, 2014
MULTI-ZONE OPERATION
The Multi-Zone mini-split will operate each zone in either cooling or heating mode but not both. The unit will
not operate as one zone cool and another heat. If this occurs, an E7 error will be displayed. To clear this
error, make sure all indoor units are in the same mode either heat or cool. Each zone will control the room
temperature at set-point and allow all normal fan, swing, turbo, timer, and sleep functions.
Emergency Operation (Auto/Stop Switch)
In the event that the remote controls are misplaced, you can operate your
inside unit by carefully raising the cover and pressing the emergency
operation switch located under the lower right hand corner of the cover.
To open the front cover, place fingers in the bottom of the slots on the side
of the indoor unit and gently pull outward. To close the cover, press down on each end and center
of the cover to latch.
DO NOT OVER EXTEND THE FRONT COVER.
If the unit is off, pressing the Emergency push
button will start the unit in the default AUTO
mode. Press the button again and it will stop the
unit.
Temperature is automatically set to 68 °F to 77°F
and will switch between COOL, HEAT or FAN
mode to maintain the temperature. If the
temperature goes below 68 °F the unit switches
to HEAT mode. If the temperature goes above
77 °F unit switches to COOL mode. If
temperature is in between 68 °F to 77°F the unit
runs in the FAN mode.
Notes:
1. Indoor fan does not turn off in the cooling mode when temperature set point has been
satisfied. It will continue to run to keep the room temperature consistent.
2. Indoor fan will turn off in heating mode when temperature set point has been satisfied.
3. Unit may require several minutes to confirm the condition of temperature set point and
system functions.
OPERATION OF WIRELESS REMOTE CONTROL
REMOTE CONTROL DISPLAY
TRANSMIT
COOL MODE
TIME DISPLAY
TIMER ON/OFF
LOCK KEYPAD
DISPLAY ILLUMINATE
PURGE
AUTO MODE
HEALTH
FAN AUTO MODE
FAN SPEED (HI, MED, LO)
SET/ INDOOR TEMP.
HEAT MODE
FOLLOW ME
VENTILATION
SLEEP MODE
TEMPERATURE DISPLAY
FAN MODE
LOUVER POSITION
DRY MODE
CLOCK SET
TURBO
OUTDOOR TEMP.

950-0194revC - 7 - March 30, 2014
REMOTE CONTROL FUNCTIONS
Note: Be sure there are no obstructions between the remote control and the receiver. Remote
control units are interchangeable, and are not assigned to a particular indoor unit. Indoor
controller will beep each time it receives a command from the remote control. Keep the remote
control away from moisture and excessive heat.TIP: Each remote will control any or all the indoor
units.
ON/OFF -Turns the unit on or off. There is a 3 minute compressor delay when the unit is turned
on.
MODE –Pressing the MODE button will select between AUTO, COOL, DRY, FAN, or HEAT (for
Heat Pump units only).
AUTO mode - Set point temperature will not be shown on the remote control display and
cannot be changed. Temperature is automatically set to 68 °F to 77 °F and will switch
between COOL, HEAT or FAN mode to maintain the temperature. If the temperature
goes below 68 °F the unit will switch to HEAT mode. If the temperature goes above 77 °F
unit switches to COOL mode. If temperature is in between the temperatures it runs in the
FAN mode.
On rare occasions while running in the AUTO mode with other zones activated there may
be an “E7” error code. “E7” error code occurs when 2 or more units are set to run in
different modes, such as HEAT and COOL. In the AUTO mode the unit automatically
switches between HEAT, COOL or FAN. If other zones are set to HEAT or COOL while
the AUTO is running in an opposite mode an “E7” will occur. To rectify this condition you
must set all the indoor units to the same mode, either HEAT or COOL, or leave the unit
KEY PAD FUNCTIONS
ON/OFF –Turns unit on or off.
-/+ - Raise, Lower set point.
FAN –Set fan speed, hi, med, lo, auto.
SWING –Set louver swing.
CLOCK –Set clock.
TIMER ON –Set timer on time.
PURGE –Extended on time for fan.
TEMP –Set point temperature / room
temperature will be displayed.
TIMER OFF –Set timer off time.
TURBO –Maximum fan speed.
SLEEP –Toggle on/off SLEEP mode.
DISPLAY –Turns display on wall unit on or
off.
LOCK KEY PAD –No changes can be
made.
ºF or ºC –Select ºF or ºC (see page 9)
FOLLOW ME –Select room temperature
sensor location (remote control or indoor
unit).
Not All Features Are Activated

950-0194revC - 8 - March 30, 2014
alone and when the temperature returns to the point where the unit switches back to the
correct mode (as the other indoor units) and all zones are in the HEAT or COOL mode, it
will clear itself and begin to run again.
COOL mode –Unit cools room to set point temperature. Set point temperature can be set
from 61 °F to 86 °F. Outdoor unit will operate in outside temperatures of +4 to +118 ºF in
the cooling mode. Indoor fan does not turn off in the cooling mode when temperature set
point has been satisfied. It will continue to run to keep the room temperature consistent.
HEAT mode (for Heat Pump units only) - Unit heats room to set point temperature. Set
point temperature can be set from 61 °F to 86 °F. Outdoor unit will operate in outside
temperatures of -5 ºF to +75 ºF in the heating mode. Indoor fan will turn off in heating
mode when temperature set point has been satisfied.
DRY mode –Set point temperature can be set from 61°F to 86°F. Unit cools at 90%
capacity while the FAN runs in LOW speed only (FAN speed cannot be changed).
FAN mode –Selects fan only operation. Set point temperature can be set from 61 °F to
86 °F. Fan speed can be set to AUTO, HIGH, MEDIUM or LOW.
SLEEP –In the COOL mode adjust the set-point temperature to a comfortable setting, and
then press the SLEEP button. After 1 hour, the set-point will increase by 1.8 ºF (1 ºC). After 2
hours have passed temperature is increased by 3.6 ºF (2 ºC). Temperature will never increase
more than 3.6 ºF (2 ºC) from set-point or beyond 86 ºF (30 ºC). The temperature will stay at this
setting until the unit is turned off or the SLEEP function is disabled.
In the HEAT mode adjust the set-point temperature to a comfortable setting, and then press the
SLEEP button. After 1 hour the set-point will decrease by 1.8 ºF (1 ºC). After 2 hours have
passed temperature is decreased by 3.6 ºF (2 ºC). Temperature will never decrease more than
3.6 ºF (2 ºC) from set point or below 61 ºF (16 ºC). The temperature will stay at this setting until
the unit is turned off or the SLEEP function is disabled.
The SLEEP mode does not work in the FAN or AUTO modes and is deactivated when the unit is
turned off or power is lost. On power up, the SLEEP mode must be turned on again if needed.
Press the SLEEP mode button to toggle SLEEP mode off and return to normal operation.
FAN –Press this button to change fan speeds, AUTO, HIGH, MEDIUM or LOW, while in the
HEAT, COOL, FAN modes. When in the AUTO setting, the fan will run faster the further away
from the set point it gets. On the other hand the closer it gets to the set point the slower it will run.
CLOCK –Press the CLOCK button, the clock ICON will start to blink. It will only blink for 5
seconds. While blinking press and hold down the + or - keys to adjust the 24H time of day clock
to the correct time. You must immediately press the CLOCK button to set the time. If the CLOCK
button is not pressed within 5 seconds, the clock time will revert back to the original setting and
clock will have to be set again.
TEMP –Press this button, the icons will be cycled between , and in the remote display.
displays set temperature always. displays room temperature for a few seconds then
display set temperature. displays set temperature.
PURGE / BLOW –When in the COOL or DRY mode and the PURGE function is enabled,
the fan will continue to operate for 10 minutes after the unit is turned off. This function dries the
evaporation coil to prevent mold and mildew. The PURGE function will remain enabled in DRY
and COOL unless power is interrupted or is disabled by the button. PURGE will not work in AUTO,
FAN or HEAT modes.
TURBO –The TURBO function will only run while in the HEAT or COOL mode. TURBO
increases indoor fan speed (more than high fan speed).
+/ -Raises or Lowers the set point temperature. Holding the button down for more than 2
seconds will cause the set point to auto increment or decrement. This does not function in the
AUTO mode since the temperature set point cannot be changed.

950-0194revC - 9 - March 30, 2014
DISPLAY –Turns the display on or off on the indoor unit. None of the lights will be
illuminated when off is selected.
SWING –Pressing the SWING button slowly, (more than 2 seconds) will start and stop the
louver moving up and down. If the button is pressed to turn on swing and then pressed again to
turn it off, the louvers will remain in that fixed position until it is turned on again.
Pressing the button quickly, (less than 2 seconds) will step
through 5 different stationary positions and then on to 3 different
swing positions, similar to the ICONS.
Right to left louvers can be manually adjusted. CAUTION: Before adjusting the horizontal louvers
turn the unit off. Make the adjustments. Turn the unit back on. This will prevent possible personal
injury and or damage to the unit.
FOLLOW ME - Press this button, the room temperature sensor is by the remote control.
Press this button again and the room temperature sensor will be in the indoor unit.
LOCK KEYPAD - Pressing the + and - buttons simultaneously will lock or unlock the keypad.
If the remote control is locked, the LOCK icon will be displayed. If a button is pressed while the
keypad is locked, the LOCK icon will blink three times, nothing will happen. If the keypad is
unlocked, the LOCK icon will not be displayed.
ICON - Press the left blank button will illuminate icon in the remote display but will have no
affect with the units.
ICON –Press the right blank button will illuminate icon in the remote display but will have
no affect with the units.
ºF or ºC - Turn unit off, press MODE and (-) buttons simultaneously to switch ºC or ºF.
REPLACING BATTERIES
The battery cover is fixed on the remote with a screw. Please
unscrew it for the very first time. (For easy use, the screw is
unnecessarily to be installed back after the batteries is placed.)
Slightly press down on the arrow on the battery cover and slide in the
direction of the arrowhead.
Remove old batteries. Insert two new AAA 1.5V batteries, paying attention
to the polarity. Re-install the back cover of wireless remote control.
NOTE:
Do not use the old, different, or rechargeable batteries.
If the wireless remote control will not be used for a long period of time,
remove the batteries.
If the wireless remote control does not operate properly, remove the batteries for 30 seconds and
re-install (resets the remote).

950-0194revC - 10 - March 30, 2014
OPTIONAL CONTROL - WALL CONTROL
●The Cassette unit operates with a wired wall control MSWCH. Using the Signal cable connect
to the printed circuit board connector CN9 in the unit and wall control.
●Wall Control can be controlled with the remote or at the panel.
●Please refer to the manual 950-0210 for detail operation and 950-0220 for detail installation of
the wall control.
Enter cancel/
Enter Cancel/Fan Mode
Function Timer On Off/
CLOCKON
FAN
FOLLOW
ME
OFF
TURBOSLEEPDISPLAY
FAN
F
SWING
/BLOWTEMP
Remote
Control
Signal Receiver
(From the Remote Control)
Signal Cable
Wall Control

950-0194revC - 11 - March 30, 2014
ROUTINE CARE AND MAINTENANCE
CAUTION
Turn main power off before cleaning air conditioner.
Never spray water into the indoor or outdoor unit for cleaning.
Volatile liquids (e.g. solvent, gasoline, etc.) will damage the air
conditioner. Wipe the unit with a dry soft cloth, or a cloth
slightly moistened with water.
Carefullyunsnap the sides and raise the cover up in the direction of arrows. Raise the cover until
it is fully extended and it will lock and hold in the up position. Now the unit can be cleaned and
serviced. Do not over extend the cover. Damage to the cover hinges will result.
Wipe the unit with a dry or slightly dampened cloth. Do not remove the
front cover from the unit.
Cleaningthe AirFilters(Recommendedonceeverythreemonths)
Note: If the unit is installed in an abnormally dusty area it is advised the filters be cleaned more
often.
Remove the air filters. Raise the cover until locked in the up position.
Pick up on the front of the filter and slide forward to remove.
To clean the dust adhering to the filters, you can either use a
vacuum cleaner, or wash them with warm water and dry it in the
shade.
NOTE: Do not use water above 113 ºF to wash filter, it can deform
the filter.
Reinstall the filters and close the cover. Turn power on, unit is ready
for use.
NEVER OPERATE THE UNIT WITHOUT FILTERS!
Outdoor unit should be cleaned and routine maintenance performed annually by a trained
Technician.

950-0194revC - 12 - March 30, 2014
Problem Troubleshooting
The unit does not run.
Is the power off?
Is the circuit protection device tripped?
Is voltage too high or low?
(Tested by a professional)
Is the Timer on?
A 3 minute delay occurs before each compressor start.
Cooling and or Heating efficiency
is not good.
Is temperature setting correct?
Are the inlet or outlet vents obstructed?
Is the filter clean?
Are windows and doors closed?
Is fan set to low speed?
Is there a heat source in the room?
Wireless remote control is not
working. (See Note 2)
Reset unit. Disconnect main power for 30 seconds then
reapply.
Is it within receiving range? Is it obstructed?
Replace the batteries.
Is remote control damaged?
Water leaking into room.
The air humidity is excessively high. Check to see if all
windows and doors are closed.
Call service Tech if not corrected by the above action.
Water leakage in outdoor unit.
When the unit is running in Auto Defrosting mode, ice will
thaw and drip into pan.
When the unit is running in HEAT mode, the water
adhered to the condenser coil drains into pan.
Noise from indoor unit emitted.
When defrosting is started or stopped, it will makea
sound. Thisis due to the refrigerant flowreversing
directions.
Normal refrigerant flowing in unit.
If E7 error code occurs, indoor units are in conflict. All units must be the same mode.
Notes:
1) If an error other than E7 is being displayed on the temperature display, it will be
necessary to call a service Tech for repair.
2) An audible beep will be heard, when a button is pressed, if the remote control is
communicating with the receiver.

950-0194revC - 13 - March 30, 2014
INDOOR UNIT ERROR CODES
Malfunction Name of
single zone
Malfunction Name of Multi
zone
Display
Running
LED
Cooling
LED
Heating
LED
/
Short/open circuit of the coil
temp. sensor for the
condenser (42K Unit Only)
oE
3 Flashes
3 Flashes
3 Flashes
Short/Open Circuit of the Liquid Valve Temp. Sensor
b5
19 Flashes
Short/Open Circuit of the Suction Valve Temp. Sensor
b7
22 Flashes
Jumper Failure
C5
15 Flashes
Trial Operation
dd
Flashing
Flashing
Flashing
Incorrect Connection of Communication Wire or
Expansion Valve Failure
dn
High Pressure Protection
E1
1 Flash
Anti-Freezing Protection
E2
2 Flashes
/
Low Pressure Protection
(42K Unit Only)
E3
3 Flashes
Exhaust Protection (Temperature Overheat)
E4
4 Flashes
Over Current Protection
E5
5 Flashes
Communication Malfunction
E6
6 Flashes
/
Mode Conflict
E7
7 Flashes
Overload Protection
E8
8 Flashes
Anti-Cold Blow
Protection
/
E9
9 Flashes
/
Condensate Water Full of
Indoor Unit
Flashing
Flashing
EEPROM malfunction (Except For 42K Unit)
EE
15 Flashes
Indoor Ambient Sensor Failure
F1
1 Flash
Indoor Tube Sensor Failure
F2
2 Flashes
Outdoor Ambient Sensor Failure
F3
3 Flashes
Outdoor Tube Sensor Failure
F4
4 Flashes
Outdoor Exhaust Sensor Failure
F5
5 Flashes
Oil Return in Cooling Mode
F7
7 Flashes
Refrigerant Recovery Mode
Fo
Flashing
Flashing
Defrost or Oil Return Heat Mode
H1
1 Flash
Electrostatic Dedust
Protection
/
H2
2 Flashes
Compressor Overload Protection
H3
3 Flashes
System Overload
/
H4
4 Flashes
IPM Protection
H5
5 Flashes
Indoor Fan Motor Failure (Except For 42K Unit)
H6
14 Flashes
Compressor Desynchronizing
H7
7 Flashes
PFC Over-current Malfunction
HC
6 Flashes
Demagnetizing Protection
for Compressor
/
HE
14 Flashes
Outdoor Fan motor
Failure
/
L3
High Supply Voltage Protection
L9
20 Flashes
Startup Failure
Lc
11 Flashes

950-0194revC - 14 - March 30, 2014
Malfunction Name of
single zone
Malfunction Name of Multi
zone
Display
Running
LED
Cooling
LED
Heating
LED
Compressor Phase Failure / Reverse Protection
Ld
/
Compressor Stalling
(42K Unit Only)
LE
3 Flashes
3 Flashes
3 Flashes
/
Over-Speed (42K Unit Only)
LF
3 Flashes
3 Flashes
3 Flashes
Indoor and Outdoor Unit
Do Not Match Each Other
/
LP
Phase Over-current Protection
P5
15 Flashes
/
Communication Error
between the Drive Board and
the Main Board
(42K Unit Only)
P6
16 Flashes
Module Temperature Sensor Failure
P7
18 Flashes
Module Overheat Protection
P8
19 Flashes
/
AC Contactor Protection
(42K Unit Only)
P9
3 Flashes
3 Flashes
3 Flashes
/
Transducer Connection
Protection (42K Unit Only)
Pd
3 Flashes
3 Flashes
3 Flashes
/
Temperature Drift Protection
(42K Unit Only)
PE
3 Flashes
3 Flashes
3 Flashes
/
Drive Board Ambient Sensor
Failure (42K Unit Only)
PF
3 Flashes
3 Flashes
3 Flashes
High Voltage Protection of DC Bus bar
PH
11 Flashes
Low Voltage Protection of DC Bus bar
PL
21 Flashes
/
AC Input Voltage Anomaly
(42K Unit Only)
PP
3 Flashes
3 Flashes
3 Flashes
Capacitor Charging Circuit Error
PU
17 Flashes
Compress Phase Circuit Detection Error
(Except for 42K Unit)
U1
12 Flashes
DC Bus bar Voltage Drop Error (Except for 42K Unit)
U3
20 Flashes
Reversing Valve Error
/
U7
Indoor fan Motor Zero-cross Detecting Error
(Except For 42K Unit)
U8
17 Flashes
Outdoor Unit Zero-cross
Detecting Error
/
U9

950-0194revC - 15 - March 30, 2014
WARRANTY
INTERNATIONAL REFRIGERATION PRODUCTS warrants the accompanying split air
conditioner or heat pump system to be free of defects in material and workmanship for the
applications specified in the operation manual and installation manual for a period of one (1) year
on parts and five (5) years on compressor, valid from the date of original retail purchase in the
United States or Canada. Labor is not covered under warranty.
If the unit exhibits a defect in normal use and is determined to be within the warranty period,
INTERNATIONAL REFRIGERATION PRODUCTS will, at its option, either repair or replace the
unit free of charge within a reasonable time after the unit is returned.
This warranty DOES NOT cover:
Damage, accidental or otherwise, to the unit while in possession of the consumer that is
not a result of a defect in material in workmanship.
Damage caused by consumer misuse, tampering, or failure to follow all care and
maintenance instructions in the manuals.
Damage to the finish of the case or other parts caused by water.
Damage caused by repairs or alterations to the unit by anyone other than a qualified
technician.
Filter.
Freight and Insurance cost for the warranty service.
Warranty Activation Card must be completed and sent in to activate the
warranty for the accompanying unit.
TECHNICAL SUPPORT
If you need technical support please call 215-750-9876 M-F 8:00am to 4:30pm ET.
When calling, please have your unit model numbers and serial numbers available.
Electronic warranty activation and product information www.irproducts.biz .
International Refrigeration Products Inc., 1035 Wheeler Way
Langhorne, PA 19047