Sealey SSCL1 V2 User manual

PLATFORM SCAFFOLD STAND
MODEL NO: SSCL1.V2
TOWER EXTENSION PACK 3 MODEL NO: SSCL3
TOWER EXTENSION PACK 4 MODEL NO: SSCL4
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING! Take care when using and moving scaffolding, extended ladders and other such equipment in the vicinity of power
cables - risk of potentially fatal electric shock.
WARNING! Ensure Health and Safety, local authority, and general workshop practice regulations are adhered to when using this
equipment.
9Familiarise yourself with the application and limitations of the scaffold, as well as the potential hazards.
9Maintain the equipment in good condition.
8DO NOT use the equipment if any parts are damaged or missing as this may cause failure and/or personal injury.
9Replace or repair damaged parts. Use genuine parts only.
9Non-authorised parts may be dangerous and will invalidate the warranty.
9Keep the work area clean, uncluttered and ensure there is adequate lighting.
WARNING! Use scaffold on level and solid ground and ensure the brakes are applied and/or that the scaffold is anchored and held firmly
in place by some means.
WARNING! DO NOT erect or use the scaffolding on sloping or unstable ground.
WARNING! Never over-reach when on the scaffolding.
9Keep children and unauthorised persons away from the working area.
8DO NOT use the scaffolding for any purpose other than that for which it is designed.
8DO NOT allow children to climb the scaffolding.
8DO NOT use the equipment when you are tired, under the influence of alcohol, drugs or intoxicating medication.
9When not in use store in a safe, dry, childproof area.
8DO NOT use the equipment without side guardrails, knee rails and toe boards fitted. Use all the components supplied.
9When used outside, mobile scaffold towers should, wherever possible, be secured to a building or other reliable structure.
9It is good practice to tie in all scaffold towers of any height, especially when left unattended or in exposed windy conditions.
Use only the recommended wall anchors.
9Beware of strong wind conditions. DO NOT erect or use a free standing tower if the wind is likely to exceed 7.7m/sec (17mph or Beaufort
force 4).
9Take care when using mobile scaffold towers in hangers or uncovered buildings as wind force may be increased due to funnelling effects.
8DO NOT climb a tower from the outside. Never climb on the horizontal or diagonal braces. You should only climb the tower on the
inside using the ladder end frames.
8DO NOT lean ladders against the tower. Never use ladders or boxes to gain additional height.
8DO NOT bridge between the mobile scaffold tower and buildings.
9Stabilisers and ballast weights shall always be tted where specied. Ballast is used at the base to stabilise towers from
overturning. Ballast must be of solid material (i.e. NOT water or loose sand) and should be positioned so as not to overload
individual legs. Ballast should be secured from accidental removal.
9Keep equipment clean and inspect before and after use for damage. Use serviceable equipment only. All working parts e.g.
castors, adjustable legs; stabiliser clamps should be lubricated lightly with oil. Repairs should only be carried out by the supplier or
other competent person approved by the supplier.
9Ensure that all personnel, tools and materials are removed from the tower prior to moving it. Only move the scaffold tower
manually on a rm level surface, which is free of any obstacles.
9Only move it longitudinally or diagonally. DO NOT exceed normal walking speed. Raise the stabilisers 12mm (½”) from the ground.
9 After moving re-lock the castors, check that the tower is level and ensure that the stabilisers are secure and have a rm footing.
8DO NOT exceed the safe working load of the platform. The maximum capacity of the working platform for an evenly distributed load is
1.5 kN/m² (according to HD1004 – scaffold tower Class 2).
8DO NOT jump on to or off the platforms.
8DO NOT use any lifting equipment on the mobile scaffold tower.
2. INTRODUCTION
SSCL1.V2: EN1004 Approved Scaffold Tower System designed to meet the UK PASMA 3T standards. Robust aluminium frame unit with
durable corrosion resistance. Heavy-duty platform with trap door for safe access to platform. SSCL1 can be used as a 3mtr or 3.8mtr
working height platform by fitting extension kit supplied with the unit. Unique design enables the unit to be quickly and easily folded down without
tools for transportation or storage. 860mm depth means unit will pass through most doorways even when fully erected. Hand rails for comfort and
safety. Four large Ø125mm castors for easy mobility.
Refer to
instruction
manual
Original Language Version
© Jack Sealey Limited SSCL1.V2, SSCL3, SSCL4 | Issue:3 (3) 12/11/19

SSCL3: Extension Kit for the SSCL1 Scaffold Tower System Increases the platform height to 3.5mtr and the working height to 5.5mtr. Supplied with
stability legs to stabilise unit and an extra trap door platform.
SSCL4: Extension Kit to be used with SSCL1 & SSCL3. Further increases the platform height to 5.15mtr and the working height to 7.15mtr.
3. SPECIFICATION
Model No:............................................................. SSCL1.V2
Width:......................................................................... 860mm
Length:..................................................................... 1780mm
Maximum Working Height: ...........................................3.8mtr
Maximum Platform Height: ...........................................1.8mtr
Weight:........................................................................ 44.8kg
Model No:...................................................................SSCL3
Width:....................................................................... 1780mm
Width with support legs: ........................................... 3810mm
Depth ......................................................................... 860mm
Maximum Working Height: ......................................... 5.5mtr*
Maximum Platform Height: ......................................... 3.5mtr*
Maximum capacity ....................................................... 200kg
Weight:........................................................................... 35kg
*Only when used with SSCL1
Model No:...................................................................SSCL4
Width:....................................................................... 1780mm
Width with support legs: ........................................... 3810mm
Depth ......................................................................... 860mm
Maximum Working Height: ...................................... 7.15mtr**
Maximum Platform Height: ...................................... 5.15mtr**
Maximum capacity ....................................................... 200kg
Weight:........................................................................... 10kg
** Only when used with SSCL1 & SSCL3
4. SSCL1.V2 CONTENTS
Reference Description Quantity
A Folding base frame with tted wheels 1
BDiagonal Brace 2
CHorizontal brace 5
D1m Guardrail end frame 2
EToe board set (2 long side, 2 short end) 1
HTrapdoor Platform 1
5. SSCL1.V2 ASSEMBLY
NOTE: The mobile scaffold tower may only be assembled, used
and dismantled by persons familiar with these Assembly and
Use Instructions.
5.1. Open folding base A and insert the locking pin in the centre of the
folding section. (See g.1)
5.2. Place diagonal B on one side on the rst rung and on the 4th
rung on the other side. (See g.2) Make sure that the buttery
locking part is completely rotated to hold the diagonal rmly in
position.
5.3. Place horizontal brace C on the rst rung and lock in position.
(See g.3)
5.4. Attach a diagonal B onto the lower rung of one of the two-rung
guardrail end frames D. (See g.4) Position the rst two-rung
guardrail end frames D (without the diagonal) on the base and
then put the two-rung guardrail end frames D already equipped
with the diagonal on the other side of the base.
(Ensure that the diagonal B is placed at an angle to the one
already on the base). (See g.4) Ensure that the buttery
locking part is completely rotated to hold the diagonal rmly in position.
Once end frames D are in position, put the 4 locking pins in place and attach the base of diagonal B on to the 5th rung of the base
frame A. (See g.5)
Place platform H on the 6th rung from the bottom. Lock the wind lock rmly into position. (See g.6).
Original Language Version
© Jack Sealey Limited SSCL1.V2, SSCL3, SSCL4 | Issue:3 (3) 12/11/19

5.5. Climb through the trapdoor, sit on the edge and position the two
lower horizontal braces C on the 2nd rung from the top. Lock the
snap locks rmly in position. (See g.7)
5.6. Remaining seated in the same position, put the other two rails C
into position on the top-most rungs. Lock the snap locks rmly into
position. (See g.8)
5.7. Install the toe boards. (See g.9)
5.8. Lock all wheels prior to using the scaffold.
6. SSCL3 CONTENTS
Reference Description Quantity
BDiagonal Brace 2
CHorizontal brace 4
HTrapdoor Platform 1
F6 Rung End Frame 2
GStabiliser Leg 4
7. SSCL3 ASSEMBLY
NOTE: The mobile scaffold tower may only be assembled, used and dismantled by persons familiar with these Assembly and Use
Instructions.
NOTE: These instructions show the assembly of SSCL1 + SSCL3 from scratch. If you already have SSCL1 assembled it will be
necessary to partly disassemble some of the upper parts so that it resembles diagram No.2 overleaf. The parts removed will be
reused in the assembly of the extended tower.
7.1. Open folding base A and insert the locking pin in the centre of the folding section. Place diagonal B on one side on the rst rung and
on the 4th rung on the other side. Make sure that the buttery locking part is completely rotated to hold the diagonal rmly in
position. Place horizontal brace C on the first rung and lock in position.
7.2. Take the two 6 rung end frames, F and 3 diagonals B. Position a diagonal on the topmost rung of one frame and another diagonal on
the second rung of the same frame but on the other side. The last diagonal is to be placed on the top rung of the second end frame.
Make sure that the buttery locking part is completely rotated to hold the diagonal rmly in position.
WARNING: Make sure that everything is the right way round as per the sketch!).
7.3. Before climbing within the frame, lock the wheels.
7.4. Position the end frames on to the folding base and lock the lower diagonal B to the 5th rung of the base frame. Make sure that
the buttery locking part is completely rotated to hold the diagonal rmly in position. Put the 4 locking pins in place to hold the
frames to the base.
7.5. Position the 4 stabiliser legs G as per the heights indicated on the sketch. Tighten firmly at the correct angle as shown above.
NOTE: Not all stabiliser legs illustrated.
7.6. Position platform H on the 5th rung from the bottom.
7.7. Climb through the trapdoor, sit on the edge and position the two horizontal braces C on the 7th rung from the bottom and the 2
braces C on the 9th rung. Lock the snap locks rmly in position.
7.8. Stand up on the platform and x the 2 diagonals B hanging from the frames into position. Make sure that the butterfly locking part is
completely rotated to hold the diagonal firmly in position.
7.9. Put the two 2-rung guardrail end frames D into position. Slide them onto the frames beneath and secure with locking pins.
7.10. Place a platform H on the 12th rung from the bottom. Climb through the access hatch, sit on the edge and position the two
horizontal braces C on the 2nd rung from the top.
7.11. Remaining seated in the same position, put the other two rails C into position on the top-most rungs. Lock the snap locks rmly in
position.
7.12. Lastly install the toe boards E.
7.13. Lock all wheels prior to using the scaffold; ensure that the stabiliser legs are secure and rmly seated on the ground.
Original Language Version
© Jack Sealey Limited SSCL1.V2, SSCL3, SSCL4 | Issue:3 (3) 12/11/19

8. SSCL4 CONTENTS
9. ASSEMBLY
NOTE: The mobile scaffold tower may only be assembled, used and dismantled by persons familiar with these Assembly and Use
Instructions.
NOTE: These instructions show the assembly of SSCL1 + SSCL3 + SSCL4 from scratch. If you already have SSCL1 + SSCL3
assembled it will be necessary to partly disassemble some of the upper parts so that it resembles diagram No.8 in the diagram on the last
page. The parts removed will be reused in the assembly of the extended tower.
9.1. Open folding base A and insert the locking pin in the centre of the folding section. Place diagonal B on one side on the first rung and on
the 4th rung on the other side. Make sure that the butterfly locking part is completely rotated to hold the diagonal firmly in position.
SSCL1.V2, SSCL3, SSCL4 | Issue:3 (3) 12/11/19
Original Language Version
© Jack Sealey Limited

9.2. Place horizontal brace C on the rst rung and lock in position.
9.3. Take 2 of the 6 rung end frames, F and 3 diagonals B. Position a diagonal on the topmost rung of one frame and the second
diagonal on the same frame on the second rung on the other side. The last diagonal is to be placed on the top rung of the second end
frame.
WARNING: Make sure that everything is the right way round as per the sketch!
9.4. Before climbing within the frame, lock the wheels.
9.5. Position the end frames on to the folding base and lock the lower diagonal B to the 5th rung of the base frame. Make sure that the
buttery locking part is completely rotated to hold the diagonal rmly in position. Put the 4 locking pins in place.
9.6. Position the 4 stabiliser legs G as per the heights indicated on the sketch. Tighten rmly at the correct angle as shown above.
NOTE: Not all stabiliser legs are illustrated.
9.7. Position platform H on the 5th rung from the bottom.
9.8. Climb through the trapdoor, sit on the edge and position the two horizontal braces C on the 7th rung from the bottom and the 2 braces
C on the 9th rung. Lock the snap locks rmly in position.
9.9. Stand up on the platform and x the 2 diagonals B hanging from the frames into position.
9.10. Take 2 of the 6 rung end frames, F and 3 diagonals B. Position a diagonal on the 4th rung of each frame but on opposite sides.
WARNING : Make sure that everything is the right way round as per the sketch!
9.11. Position the end frames on to frame below and x the 2 diagonals B hanging from the frames into position. Make sure that the
buttery locking part is completely rotated to hold the diagonal rmly in position. Insert the frame locking pins.
9.12. Position a platform H on the 11th rung and lock in place.
9.13. Climb through the trapdoor, sit on the edge and position the two horizontal braces C on the 13th rung from the bottom and the 2
braces C on the 15th rung. Lock the snap locks rmly in position.
9.14. Attach a diagonal B onto the lower rung of one of the two-rung guardrail end frames D.
9.15. Position the rst two-rung guardrail end frame D (without the diagonal) on the base and then put the two-rung guardrail end frame D
already equipped with the diagonal on the other side of the base. Fix the diagonal in place on the 17th rung. Make sure that the butterfly
locking part is completely rotated to hold the diagonal firmly in position. Insert the frame locking pins.
9.16. Climb down to the lowest platform and sitting in the access hatch remove the 4 horizontal braces from rungs 7 and 9 and pass them to
the ground.
9.17. Climb to the ground and remove the lower platform.
9.18. Ascend to the platform on rung 11 and reposition the other platform on the 18th rung from the bottom. Lock the wind locks securely.
9.19. Climb through the trapdoor, sit on the edge and position the two lower horizontal braces C on the 2nd rung from the top. Lock the
snap locks rmly in position . Remaining seated in the same position, put the other two rails C into position on the top-most rungs. Lock
the snap locks firmly into position.
9.20. Lastly install the toe boards E.
9.21. Lock all wheels prior to using the scaffold; ensure that the stabiliser legs are secure and rmly seated on the ground.
10. MAINTENANCE
10.1. Keep all of the equipment clean and inspect before EVERY use for damage. Remove from service if damaged in any way.
10.2. Lubricate all moving parts: castors, adjustable legs, stabiliser clamps, lightly with oil.
.
SSCL1 + SSCL3 SSCL1 + SSCL3 +
SSCL4
SSCL1.V2, SSCL3, SSCL4 | Issue:3 (3) 12/11/19
Original Language Version
© Jack Sealey Limited

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Original Language Version
© Jack Sealey Limited SSCL1.V2, SSCL3, SSCL4 | Issue:3 (3) 12/11/19
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call
our technical team on [e-mail] or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.