Atak AXS2040 User manual

20’’-40’’
66 lbs.
Supports VESA sizes up to: 200x200
For technical assistance or troubleshooting
please call 1-855-994-2825 or visit www.sibrandssupport.com
This product Wall Mount frame is intended for use only with an apparatus which has a maximum weight of 66 lbs. See apparatus
instructions. Using with an apparatus heavier than the maximum weight indicated may result in instability and cause possible
injury.
READ THIS FIRST Read this entire manual! Do not attempt to install this product if you do not understand the instructions.
Contact a qualified mount installer if you have any doubts about a safe and secure mount installation, or if you are not sure what
specific wall materials you are attaching this mount to. Check all the parts carefully to make sure there are no missing or
damaged parts. Improper installation may result in damage to your TV, property, and personal injury.
Tilting & Swiveling
Flat Panel Wall Mount
Installation Guide
Model: AXS2040

ATAK

Parts and Hardware
WARNING: This product contains small items that could be a choking hazard if
swallowed. Before starting assembly, verify all parts are included and undamaged.
NOTE: Not all hardware included will be used.
M4x12mm
M5x12mm
M6x12mm
M8x25mm
M4x30mm
M5x30mm
M6x35mm
M8x50mm
M5/M6x17mm M8x22mm
M5/M4 M6
10mm 2.5mm
2
Washers
Spacers
TV Screws
x4
x4
x4
x4
x4
x4
x4 x4
x4
x4 x4
x4 x8
x4
Allen Key
x1
1-1 Disassemble Wall Plate Unit into Two Pieces by removing the two screws (#5)
Wall Plate Unit
x1
Wa ll
plate
TV plate

3
1-2 Choose Configuration
M8
M6
M5
M4
1-3 Select TV Screws
TV back
Bracket Washer
Bracket
Long Screw
Spacer
No, go to PAGE 4 for detailed combination.
Yes, go to PAGE 4 for detailed combination.
TV back
1-4 Need spacers?
Short Screw
Washer
①100mm x 100mm
②200mm x 100mm
③200mm x 200mm
① ①
① ①
② ②
②②
③
③③
③
Align the 4 holes on the rear of your TV with the 4 corresponding holes
on the TV plate from options 1, 2, or 3.

4
Tips: If you need to combine M8(d/h) screw with 2.5mm Spacer(n), you have to remove
the inner circle of the Spacer (n).
Screw and washer
Spacer(s), screw and washer
1-5 Attach the TV Plate to the Rear of the TV
No!

For wood stud installation, follow STEP 2A
For concrete installation, follow STEP 2B on PAGE 7
<16mm
(5/8")
Min. Wood Stud Size:
nominal 2"(51mm)
actual 1 1/2"(38mm)
Min. Wood Stud Size:
nominal 4"(102mm)
actual 3 1/2"(89mm)
Parts and Hardware
Wood Stud Installation
Lag Bolt M8x60mm
M8 Washer
x2 x2
Concrete Wall Anchor 2pcs
CAUTION:Do not use in drywall or wood
Socket tool
x1
5
Wall plate

7/32"
(5.5mm)
Go to Step 3 on PAGE
8.
O
Center line
2.5"(64mm)
CAUTION: To avoid potential personal injury or property damage:
Both lag bolts MUST BE firmly tightened to prevent unwanted movement of the wall plate
assembly. Ensure the wall plate assembly is securely fastened to the wall before continuing on to
the next step.
To prevent the TV falling down, the Bolt Head Must Face UP at this step!!
No!
Wall plate
Bolt Head UP!
Wall plate
Use a pencil to mark the center
of the stud.
Use a pencil to mark the mounting holes on the
wall. Make sure the holes will be in the center
of the stud.
Use 5/32” (4mm) drill bit to pre-drill holes
at least 2.5” inches (64mm) deep at the
marked locations.
Use the lag bolts (1) and washers (2) to secure
the Wall Plate to the wall.

Solid Conrete Wall Installation
7
2.5"
(64mm)
3/8"
(10mm)
Concrete Wall
Anchor
DANGER
Min.
8"(203mm)
CAUTION: To avoid potential personal injury or property damage:
Both lag bolts MUST BE firmly tightened to prevent unwanted movement of the wall plate
assembly. Ensure the wall plate assembly is securely fastened to the wall before continuing on to
the next step.
To prevent the TV falling down, the Bolt Head Must Face UP at this step!!
No!
Wall plate
Bolt Head UP!
Wall plate
Use 3/8” (10mm) drill bit to
pre-drill holes at least 2.5” inches
(64mm) deep at the marked locations.
Use the Lag bolts (1) and
Washers (2) to secure the Wall Plate
to the wall.
Use a pencil to mark the
mounting holes on the wall.
Insert a Wall Anchor into each
pre-drilled hole and lightly tap it with
a hammer until the Wall Anchor is flush
with the wall.
WATER LINE ELECTRIC LINE

8
66 LBS (30 kg)
Before hanging TV, please conduct "wall plate installation integrity test" first.
TV
1 2 Re-attach the Wall Plate
and TV Plate using the
two screws (#5)

4-1 TV leveling adjustment (±5°):
Loosen 2 leveling bolts on the rear of TV plate by maximum 2
turns, adjust to level, and retighten to secure.
4-2 Tilting angle adjustment (+5°/-15°)：
Pull TV to your desired angle then fasten 2 tilting bolts with
Allen key .
Tilting bolts Tilting bolts
9
Loosen
Tighten
-15°
+5°

10
200mm
224mm
200mm
224mm
80mm
145mm
78mm
+5°
-15°
+15°/-15°

LIMITED SIX-YEAR WALL MOUNT WARRANTY
We warrant this product to you, the original purchaser at the time of purchase printed on a dated store receipt from
an authorized ATAK retailer and for a period of six-years thereafter that our wall mount product and all it’s parts
and components are free of defects in material and workmanship under normal use. This warranty is subject to
the provisions below. ATAK’s sole obligation and the purchaser’s exclusive remedy pursuant to these warranties
are limited to replacement at ATAK’s sole discretion. There are no other warranties except as expressively set
forth below either expressed or implied, including any warranty of merchantability for any particular purpose.
Should you be missing any of the assembly parts or components (screws, pieces, etc.), please contact the
Customer Support Center to secure a replacement. It is not necessary to bring the unit back to the store. When
calling, please reference the parts list found in the Instruction Manual to help us accurately identify the missing
parts and promptly provide replacements.
Our Customer Support Center is available Monday to Saturday (10:00AM to 7:00PM EST) for technical assistance
or troubleshooting. To contact us please call 1-855-994-2825 or visit www.sibrandssupport.com
This warranty is expressly limited to the replacement of wall mount parts and components described in the parts
list located in the Instruction Manual included with the product.
This warranty applies under conditions of normal use.
This warranty does not cover: any product, which has been subject to damage due to improper assembly or
disassembly, products which were not assembled, installed, used, or maintained in accordance with the product
assembly instructions & warnings, acts of nature, misuse, neglect, accidents, abuse, exposure to elements,
outdoor use, extreme temperature ranges, damage during transit, commercial use, modification of, or to any part
of the product or attachments to the product not approved by ATAK. Also not covered are costs for
assembly/dis-assembly labor, costs incurred in shipping the unit or parts for warranty repair/exchange or any
products purchased from unauthorized ATAK sellers. Under no circumstances shall ATAK, be liable for any loss
(direct, indirect, incidental, foreseen, unforeseen, special or consequential) or for any damage arising out of, or in
connection with, the use of this product. Nor shall ATAK have any responsibility for incidental or consequential
damages resulting from the breach of this warranty including but not limited to inconvenience, purchase or rental
of replacement products, loss of profits or commercial loss.
We reserve the right to request damaged parts or units be shipped to our offices for inspection or confirmation of
any warranty claims.
This warranty does not cover product sold ‘As Is’.
This warranty is valid only to the original purchaser of the Product in the United States and Canada and grants
specific legal rights.
PN: ATAK AXS2040 Rev 1.0 July 2018
2018
ATAK