Sealey AP7150C User manual

INSTRUCTIONS FOR:
CORNER RACKING UNIT 5 LEVEL -
150KG CAPACITY PER LEVEL
MODEL No: AP7150C
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
2. INTRODUCTION
3. CONTENTS
1.1. GENERAL SAFETY
WARNING! Ensure Health & Safety, local authority, and
general workshop practice regulations are adhered to when
using this racking unit.
Locate racking unit in a suitable work area.
Keep the work area clean, uncluttered and ensure there is
adequate lighting.
WARNING! Use racking unit on level and solid ground,
preferably concrete.
Keep the racking unit clean and tidy in accordance with
good workshop practice.
Keep children and unauthorised persons away from the work
area.
DO NOT use the racking unit for any purpose other than
that for which it is designed.
DO NOT use the racking unit outdoors.
DO NOT place the racking unit in a damp or wet location or
an area where there is condensation.
DO NOT clean the racking unit with any solvents which
may damage the surfaces or the protective coating.
 DO NOT move the racking unit when there are items
placed on it.
 DO NOToverload the racking unit.
Fully painted steel frame with ve shelves. Space saving corner unit with
150kg capacity per level giving a maximum capacity of 750kg per rack.
Two piece uprights allow use as a single bay rack or split into two
separate shelf systems or workstations. Ideal for use in conjunction with
Model No. AP7200 racking unit.
Dimensions:
Overall Width: 730mm, Depth: 730mm, Height: 1830mm.
Unpack the contents of the box and check against the parts
list. If there are any parts missing, contact your Sealey dealer.
Part Part Name No. of
A Shelf Bracket - Rear 8
B Shelf Bracket - Side 8
C Top Shelf Bracket - Rear 2
D Top Shelf Bracket - Side 2
E Shelf Bracket - Front 4
F Top Shelf Bracket - Front 1
G Shelf Brace 5
H Leg 6
I Leg 4
J Shelf 5
K Plastic Foot 3
L Plastic Foot 2
M Connector 5
Original Language Version AP7150C Issue: 1 - 22/08/12
© Jack Sealey Limited

4.1. Assemble the racking unit following the sequence below, referencing the parts list overleaf. No tools are required
although a mallet is useful for tapping the brackets together.
4. ASSEMBLY
Original Language Version AP7150C Issue: 1 - 22/08/12
© Jack Sealey Limited
Fig.1 Fig.2
Fig.3 Fig.4
4.2. Place foot caps onto the bottom of legs H and I. Place
rear shelving brackets A onto the legs. A rubber mallet
can be used to lightly tap the brackets into place in the
keyholes in the legs (note the upright position of the
keyhole).
4.3. Fit shelf bracket B for the side brackets at the same
height as shelf bracket A, then t shelf bracket E. Fit
brace G as shown above.
4.4. Join the lower and upper legs with the connector pins
as shown in Fig.3 (note the upright position of the
keyhole).
4.5. Fix shelf brackets A so that the top rivet sits in the
upper legs and the lower rivet sits in the lower legs.
Repeat with shelf brackets B and E, followed by brace
G, at the same level.

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
[e-mail]
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business
Park, Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
email
Original Language Version AP7150C Issue: 1 - 22/08/12
© Jack Sealey Limited
4.6. Fix brackets C, D and F at the very top allowing space
for the MDF shelf to sit ush against the legs.
Fig.5 Fig.6
Fig.7
4.7. Apply remaining brackets at desired heights, ensure a
brace G is also xed at each shelf height.
4.8. Place the MDF shelves at each height ensuring that
they sit ush on the brackets.
NOTE: DO NOT t the shelves until racking unit is
otherwise complete.