Seat Comfort Systems SCS6MC User manual

Revitalizer Massage
Installation Manual
SCS6MC
Seat Comfort Systems
www.seatcomfort.com
Seat Comfort Systems

Massage System Parts List
P2
The Reviltalzer Massage System is a vibration system that has been designed
to be installed into the seat back foam in a minimal amount of time with readily
available tools. The unique design allows the driver and passenger to experience
revitalizing massage in the Lumbar area in almost all of today's vehicles.
GENERAL ADVICE:
- The Revitalizer is to be installed into the back foam. Always check the motor
placement on the seat prior to beginning any work. Make sure there are no
obstacles that would not allow the motors to be installed.
- Check for Occupant Detection System in the seat back prior to installing.
The system cannot be installed under an Occupant Detection System.
- The installer is liable for any damage due to improper installation.
- All steps explained in this manual are to be followed with great care.
- Installation has to be performed by qualified personnel only.
- Improper installation will void the limited warranty provided by the
manufacturer and may cause physical damage to equipment or people.
- The massage system has to be connected to 12 volt accessory power and
draws a maximum of 2 Amps continuous current.
- The wire harness has to be fitted to the seat in a way that the full range of
movement of the seat is possible without damaging the wire harness.
- Cars fitted with side airbags have to be treated according to the manufacturers
fitting manuals. The massage system is only to be attached to the middle of the
seat back foam.
Important Safety Instructions
Motor set - 6 pcs
Connection box - 1 pc
Wand with curly cord - 1 pc
Power wire -1 pc
H/T
P/W
41
40
20
31
30
21
Fuse
Red Line:
Black Line : -
+
Connect Box

P3
Motor Placement
The motors are to be located on both sides
of seat back leaving the spine area open. It is
recomended that a set of motors are located
below the belt line and then stacked. The
motors should not be positioned in the
shoulder blade, neck or head area. To
begin the installation, locate the
massage areas and mark the positions
(tape) while sitting on the seat. This will
reference the locations when the cover
is removed.
1.Locate motor placement on seat back.
2. Remove seat cover and locate and verify motor placement.
3. Trace the motor on the foam, cut out the foam and set motor in cavity
4.Pass the motor wire through the foam and attach to the distribution box.
5. Connect all wires and test the system and motors
6. Adhere motors into the foam
7.Place 1/4" foam over the motors and cavity if necessary
8. Instal the connection box into the seat back and tie any loose wires.
9. Check placement of boxes as not to interfere with lumbar/recliner
10. Run power wire to 12 volt supply and test system
11. Re-cover the seat back.
12. Place control wand in vehicle and test
Options:
3A. Cut a slit into the foam, create a cavity with your fingers and slip motors into place.
This may create a lump in the foam but it will enhance the massage effect
21
20
30 31
40 41

P4
Motor Installation
Cut out the foam to receive the shape of the motor housing by pulling back the
long cut of the foam and placing the blade on an angle and cut towards the
center. Repeat this on the other side and remove the foam cutout .
Gluing Motors:
Using spray glue, apply into the foam cavity and then place motor into foam
cavity and gently pull the motor wires to insure a light fit, Apply pressure to the
top of motors and hold against the foam for 15 seconds.
(A.) Foam Cutout:
Cross Section Of Foam
1 "
2 "
(B.) Verify that all motors are operational before Gluing:
MOTOR
Apply glue in these areas Apply glue in these areas
Cover the motor cavity with needlepunch or 1/4" foam.
(C.) Motor Cover (if necessary)
1/4"Foam If Required
MOTOR
Cross Section Of Foam
Glue

P5
Wire Placement
Route the motor wires through the foam and connect to the
distribution box (below). Make sure that there are no loose
wires that may interfere with the lumbar or recliner mechanisms.
Attach the power connector wire to P/W (below) and route the wire
with fuse to 12 volt power.
20 - Zone 6 - Upper Back: Left
21 - Zone 6 - Upper Back: Right
30 - Zone 7 - Middle Back: Left
31 - Zone 7 - Middle Back: Right
40 - Zone 8 - Lower Back: Right
41 - Zone 8 - Lower Back: Left
P/W - Power
Connector/Zone Locations

System Power Connection
Power Connection To Vehicle
1.Run the power harness under the carpet and along the
scuff plate toward the fuse box.
2.Install the negative wire to ground and secure in place.
3.Connect the red wire (positive) to 12 volt power.
Fuse
Harness Extension
Ground
Fuse Box
Fuse Box Wiring
P6

Operating Instructions
P7
Massage Description
Massage Operation
On/Off - This button turns on the massage system
Function - Cycles through 8 programs
Time - Selects duration of massage
Speed - Increases or decreases massage intensity
1: Z1 - Z2 - Z3 : "Chaos"
2: Z1 - Z2 - Z3 : "Wave"
3: Z1 - Z2 - Z3 : "Wave" with intensity: low to high
4: Z1 and Z3 - Z2 : "Criss Cross"
5: Z1+Z2+Z3 : "Revitalizer" all motors on
6: Z3 : Single zone massage
7: Z2 : Single zone massage
8: Z1 : Single zone massage

Seat Comfort Systems - Warranty Information
36 MONTH/36,000 MILE LIMITED WARRANTY
Seat Comfort Systems warrants to the original retail purchaser of this product
that should this product or any part thereof, under normal use and conditions, be
proven to have defective material or workmanship within 36 months or 36,000
miles of the original purchase, such defect(s) will be repaired or replaced without
charge for the parts. This warranty does not apply to batteries or normal wear
and tear associated with the Product.
To obtain repair or replacement with the terms of this Warranty, the product is to
be returned with warranty card, dated bill of sale, description of defect to the
installing dealer and/or retailer.
This Warranty does not cover costs incurred for the removal or reinstallation of
the product, and/or related components, and/or damage to the vehicle's electrical
system or components.
This Warranty does not apply to any product or part thereof which in the opinion
of the Company has been damaged through alteration, improper installation,
misuse, neglect, accident, or customer abuse.
No person or representative is authorized to assume for the Company any
liability other than expressed herein in connection with the sale of this product.
THE EXTENT OF THE COMPANYS LIABILITY UNDER THIS WARRANTY IS
LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN
NO EVENT, SHALL THE COMPANY'S LIABILITY EXCEED THE PURCHASE
PRICE PAID BY THE PURCHASER FOR THE PRODUCT.
WARNING: The installation instructions have been carefully compiled through
actual vehicle installations and to the best of our ability is accurate. However, we
do not warrant the accuracy of this information against changes in vehicle design,
the use or misuse of this information or typographical errors.
It is the responsibility of the installer to verify the proper wire attachments prior to
and after the installation to assure proper operation. We do not accept any
responsibility for damage to the vehicle or injury to its occupants caused by the
use of this information. Improper installation and/or connection to the incorrect
wires could cause the massage system or vehicle malfunction, component
damage and/or personal injury for you and/or your passengers.
Seat Comfort Systems Inc.
[phone]
P8