manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Secabo
  6. •
  7. Storage
  8. •
  9. Secabo Shelving table 16 User manual

Secabo Shelving table 16 User manual

Hier sind ein paar wichtige Hinweise die sie beim Verwenden Ihrer SH7 Softheat beachten sollten:
Here are a few important tips to keep in mind when using your SH7 Softheat:
Hier haben wir das ganze Handling mit der SH7 vom Auspacken bis zur Aufbewahrung für Sie noch als Video visualisiert.
Falls Sie noch Fragen haben melden Sie sich jederzeit gerne per E-mail an [email protected]
Here we have visualised the entire handling of the SH7 from unpacking to storage for you as a video. If you have any ques-
tions, please do not hesitate to contact us by e-mail at [email protected].
QUICK GUIDE SH7 SOFTHEAT
WWW.SECABO.COM
1.) Auspacken
Die Secabo SH7 wird mit einer Silikonmatte und einem Überzug
versendet um die Membranfläche zu schützen. Nehmen Sie diese
vorsichtig aus dem Karton.
5.) Nach Benutzung
Nachdem Sie die SH7 benutzt haben, lassen Sie diese bitte vollstän-
dig abkühlen. Danach können Sie die Silikonmatte und den Schutz-
überzug wieder anbringen. Nun kann die Platte von der Presse ab-
montiert werden.
2.) Montieren
Nehmen Sie die SH7 sowie aus der Verpackung und schieben Sie
diese an den Pressenkopf. Dann montieren Sie wie gewohnt die
Schrauben und ziehen diese fest.
6.) Ablegen
Nach der Abmontage tellen Sie sicher, dass die Silikonmatte und der
Schutzüberzug richtig an der SH7 angebracht sind.
7.) Aufbewahrung
Überprüfen Sie nochmal bevor Sie die SH7 lagern ob die Silikonmat-
te auch wirklich die Membrane komplett abdeckt. Somit garantieren
Sie auch einen längeren Erhalt der SH7 und verhindern einen zu
schnelle Abnuntzung.
8.) Lagern
Nun können Sie die SH7 ablegen und für den nächsten Einsatz
bereithalten.
3.) Überzug entfernen
Wenn die SH7 richtig angebracht wurde, können Sie nun den Üner-
zug und die Silikonmatte abziehen.
4.) Anschließen und loslegen
Nun können Sie die Kabel mit der Presse verbinden und die Presse
in Betrieb nehmen. Bitte beachten Sie, dass die Transferpresse nicht
mehr als 190° C aufheizen dürfen. Bitte kleben Sie zur Sicherheit den
gelben Warnaufkleber noch auf ihren Controller. (Liegt bei)
1.) Unpacking
The Secabo SH7 is shipped with a silicone mat and a cover to
protect the membrane surface. Carefully remove them from the
box.
5.) After use
After you have used the SH7, please let it cool down completely.
Then you can put the silicone mat and the protective cover back
on. Now the plate can be removed from the press.
2.) Mount
Take the SH7 out of the packaging and slide it onto the press
head. Then mount the screws as usual and tighten them.
6.) Dismount
After dismantling, make sure that the silicone mat and the pro-
tective cover are properly attached to the SH7.
7.) Storage
Before storing the SH7, check again that the silicone mat really
covers the membrane completely. This will guarantee that the
SH7 will last longer and prevent it from wearing out too quickly.
8.) Store
Now you can store the SH7 and have it ready for the next use.
3.) Remove the cover
If the SH7 has been fi tted correctly, you can now remove the
cover and the silicone mat.
4.) Connect and start
Now you can connect the cables to the press and start using
the press. Please note that the heat of the heat press must not
exceed 190° C. To be on the safe side, please stick the yellow
warning sticker on your controller. (Enclosed)
ACHTUNG! Bitte bringen Sie den beigefügten Warnhinweis-Sticker an dem Controller Ihrer Transferpresse an!
ATTENTION! Please attach the enclosed warning sticker to the controller of your heat press!
Nicht mehr als
190° C aufheizen
Do not heat more
than to 190° C
SH7 Softheat
!!
Shelving table 16
Work table 16 (77cm x 77cm x 90cm)
Abb. ähnlich
Secabo Modulares Shelving System • Secabo Modular Shelving System
Shelving table 16
Work table 16 (77cm x 77cm x 90cm) Art.Nr.: 183.000.00
QUICK GUIDE
Hier sind ein paar wichtige Hinweise die sie beim Verwenden Ihrer SH7 Softheat beachten sollten:
Here are a few important tips to keep in mind when using your SH7 Softheat:
Hier haben wir das ganze Handling mit der SH7 vom Auspacken bis zur Aufbewahrung für Sie noch als Video visualisiert.
Falls Sie noch Fragen haben melden Sie sich jederzeit gerne per E-mail an [email protected]
Here we have visualised the entire handling of the SH7 from unpacking to storage for you as a video. If you have any ques-
tions, please do not hesitate to contact us by e-mail at [email protected].
QUICK GUIDE SH7 SOFTHEAT
WWW.SECABO.COM
1.) Auspacken
Die Secabo SH7 wird mit einer Silikonmatte und einem Überzug
versendet um die Membranfläche zu schützen. Nehmen Sie diese
vorsichtig aus dem Karton.
5.) Nach Benutzung
Nachdem Sie die SH7 benutzt haben, lassen Sie diese bitte vollstän-
dig abkühlen. Danach können Sie die Silikonmatte und den Schutz-
überzug wieder anbringen. Nun kann die Platte von der Presse ab-
montiert werden.
2.) Montieren
Nehmen Sie die SH7 sowie aus der Verpackung und schieben Sie
diese an den Pressenkopf. Dann montieren Sie wie gewohnt die
Schrauben und ziehen diese fest.
6.) Ablegen
Nach der Abmontage tellen Sie sicher, dass die Silikonmatte und der
Schutzüberzug richtig an der SH7 angebracht sind.
7.) Aufbewahrung
Überprüfen Sie nochmal bevor Sie die SH7 lagern ob die Silikonmat-
te auch wirklich die Membrane komplett abdeckt. Somit garantieren
Sie auch einen längeren Erhalt der SH7 und verhindern einen zu
schnelle Abnuntzung.
8.) Lagern
Nun können Sie die SH7 ablegen und für den nächsten Einsatz
bereithalten.
3.) Überzug entfernen
Wenn die SH7 richtig angebracht wurde, können Sie nun den Üner-
zug und die Silikonmatte abziehen.
4.) Anschließen und loslegen
Nun können Sie die Kabel mit der Presse verbinden und die Presse
in Betrieb nehmen. Bitte beachten Sie, dass die Transferpresse nicht
mehr als 190° C aufheizen dürfen. Bitte kleben Sie zur Sicherheit den
gelben Warnaufkleber noch auf ihren Controller. (Liegt bei)
1.) Unpacking
The Secabo SH7 is shipped with a silicone mat and a cover to
protect the membrane surface. Carefully remove them from the
box.
5.) After use
After you have used the SH7, please let it cool down completely.
Then you can put the silicone mat and the protective cover back
on. Now the plate can be removed from the press.
2.) Mount
Take the SH7 out of the packaging and slide it onto the press
head. Then mount the screws as usual and tighten them.
6.) Dismount
After dismantling, make sure that the silicone mat and the pro-
tective cover are properly attached to the SH7.
7.) Storage
Before storing the SH7, check again that the silicone mat really
covers the membrane completely. This will guarantee that the
SH7 will last longer and prevent it from wearing out too quickly.
8.) Store
Now you can store the SH7 and have it ready for the next use.
3.) Remove the cover
If the SH7 has been fi tted correctly, you can now remove the
cover and the silicone mat.
4.) Connect and start
Now you can connect the cables to the press and start using
the press. Please note that the heat of the heat press must not
exceed 190° C. To be on the safe side, please stick the yellow
warning sticker on your controller. (Enclosed)
ACHTUNG! Bitte bringen Sie den beigefügten Warnhinweis-Sticker an dem Controller Ihrer Transferpresse an!
ATTENTION! Please attach the enclosed warning sticker to the controller of your heat press!
Nicht mehr als
190° C aufheizen
Do not heat more
than to 190° C
SH7 Softheat
!!
Shelving Table 16
Sophisticated and practical - with the Shelving Table 16, up to 16 rolls of fi lm can be
stored gently and without scratches, while the plotter or transfer press fi nd their place
on the tabletop.
Technical data
Brand: Secabo
Size of work surface: 77 x 77 cm
Dimensions LxWxH : 77 x 77 x 90 cm
Weight: 31 kg
Load limit: 70 kg (on the worktop)
Secabo Modular Shelving System
As individual as your requirements.
The needs of daily work are as individual as the person doing it. We at Secabo have
long recognised this and with the Secabo Modular Shelving System we now offer the
optimum solution for the individual construction of your personal working environment.
From shelves and racks for storing rolls of fi lm to tables for transfer presses and cutting
plotters - the modular system offers unlimited possibilities! Optionally, a roll holder can
also be attached to make working with the cutting plotter even easier. In addition to
various sizes, the high-quality modules are available as stand-alone models, rollable or
for wall mounting.
Shelving table 16
Work table 16 (77cm x 77cm x 90cm)
Hier sind ein paar wichtige Hinweise die sie beim Verwenden Ihrer SH7 Softheat beachten sollten:
Here are a few important tips to keep in mind when using your SH7 Softheat:
Hier haben wir das ganze Handling mit der SH7 vom Auspacken bis zur Aufbewahrung für Sie noch als Video visualisiert.
Falls Sie noch Fragen haben melden Sie sich jederzeit gerne per E-mail an [email protected]
Here we have visualised the entire handling of the SH7 from unpacking to storage for you as a video. If you have any ques-
tions, please do not hesitate to contact us by e-mail at [email protected].
QUICK GUIDE SH7 SOFTHEAT
WWW.SECABO.COM
1.) Auspacken
Die Secabo SH7 wird mit einer Silikonmatte und einem Überzug
versendet um die Membranfläche zu schützen. Nehmen Sie diese
vorsichtig aus dem Karton.
5.) Nach Benutzung
Nachdem Sie die SH7 benutzt haben, lassen Sie diese bitte vollstän-
dig abkühlen. Danach können Sie die Silikonmatte und den Schutz-
überzug wieder anbringen. Nun kann die Platte von der Presse ab-
montiert werden.
2.) Montieren
Nehmen Sie die SH7 sowie aus der Verpackung und schieben Sie
diese an den Pressenkopf. Dann montieren Sie wie gewohnt die
Schrauben und ziehen diese fest.
6.) Ablegen
Nach der Abmontage tellen Sie sicher, dass die Silikonmatte und der
Schutzüberzug richtig an der SH7 angebracht sind.
7.) Aufbewahrung
Überprüfen Sie nochmal bevor Sie die SH7 lagern ob die Silikonmat-
te auch wirklich die Membrane komplett abdeckt. Somit garantieren
Sie auch einen längeren Erhalt der SH7 und verhindern einen zu
schnelle Abnuntzung.
8.) Lagern
Nun können Sie die SH7 ablegen und für den nächsten Einsatz
bereithalten.
3.) Überzug entfernen
Wenn die SH7 richtig angebracht wurde, können Sie nun den Üner-
zug und die Silikonmatte abziehen.
4.) Anschließen und loslegen
Nun können Sie die Kabel mit der Presse verbinden und die Presse
in Betrieb nehmen. Bitte beachten Sie, dass die Transferpresse nicht
mehr als 190° C aufheizen dürfen. Bitte kleben Sie zur Sicherheit den
gelben Warnaufkleber noch auf ihren Controller. (Liegt bei)
1.) Unpacking
The Secabo SH7 is shipped with a silicone mat and a cover to
protect the membrane surface. Carefully remove them from the
box.
5.) After use
After you have used the SH7, please let it cool down completely.
Then you can put the silicone mat and the protective cover back
on. Now the plate can be removed from the press.
2.) Mount
Take the SH7 out of the packaging and slide it onto the press
head. Then mount the screws as usual and tighten them.
6.) Dismount
After dismantling, make sure that the silicone mat and the pro-
tective cover are properly attached to the SH7.
7.) Storage
Before storing the SH7, check again that the silicone mat really
covers the membrane completely. This will guarantee that the
SH7 will last longer and prevent it from wearing out too quickly.
8.) Store
Now you can store the SH7 and have it ready for the next use.
3.) Remove the cover
If the SH7 has been fi tted correctly, you can now remove the
cover and the silicone mat.
4.) Connect and start
Now you can connect the cables to the press and start using
the press. Please note that the heat of the heat press must not
exceed 190° C. To be on the safe side, please stick the yellow
warning sticker on your controller. (Enclosed)
ACHTUNG! Bitte bringen Sie den beigefügten Warnhinweis-Sticker an dem Controller Ihrer Transferpresse an!
ATTENTION! Please attach the enclosed warning sticker to the controller of your heat press!
Nicht mehr als
190° C aufheizen
Do not heat more
than to 190° C
SH7 Softheat
!!
Secabo Modulares Shelving System • Secabo Modular Shelving System
QUICK GUIDE
Hier sind ein paar wichtige Hinweise die sie beim Verwenden Ihrer SH7 Softheat beachten sollten:
Here are a few important tips to keep in mind when using your SH7 Softheat:
Hier haben wir das ganze Handling mit der SH7 vom Auspacken bis zur Aufbewahrung für Sie noch als Video visualisiert.
Falls Sie noch Fragen haben melden Sie sich jederzeit gerne per E-mail an [email protected]
Here we have visualised the entire handling of the SH7 from unpacking to storage for you as a video. If you have any ques-
tions, please do not hesitate to contact us by e-mail at [email protected].
QUICK GUIDE SH7 SOFTHEAT
WWW.SECABO.COM
1.) Auspacken
Die Secabo SH7 wird mit einer Silikonmatte und einem Überzug
versendet um die Membranfläche zu schützen. Nehmen Sie diese
vorsichtig aus dem Karton.
5.) Nach Benutzung
Nachdem Sie die SH7 benutzt haben, lassen Sie diese bitte vollstän-
dig abkühlen. Danach können Sie die Silikonmatte und den Schutz-
überzug wieder anbringen. Nun kann die Platte von der Presse ab-
montiert werden.
2.) Montieren
Nehmen Sie die SH7 sowie aus der Verpackung und schieben Sie
diese an den Pressenkopf. Dann montieren Sie wie gewohnt die
Schrauben und ziehen diese fest.
6.) Ablegen
Nach der Abmontage tellen Sie sicher, dass die Silikonmatte und der
Schutzüberzug richtig an der SH7 angebracht sind.
7.) Aufbewahrung
Überprüfen Sie nochmal bevor Sie die SH7 lagern ob die Silikonmat-
te auch wirklich die Membrane komplett abdeckt. Somit garantieren
Sie auch einen längeren Erhalt der SH7 und verhindern einen zu
schnelle Abnuntzung.
8.) Lagern
Nun können Sie die SH7 ablegen und für den nächsten Einsatz
bereithalten.
3.) Überzug entfernen
Wenn die SH7 richtig angebracht wurde, können Sie nun den Üner-
zug und die Silikonmatte abziehen.
4.) Anschließen und loslegen
Nun können Sie die Kabel mit der Presse verbinden und die Presse
in Betrieb nehmen. Bitte beachten Sie, dass die Transferpresse nicht
mehr als 190° C aufheizen dürfen. Bitte kleben Sie zur Sicherheit den
gelben Warnaufkleber noch auf ihren Controller. (Liegt bei)
1.) Unpacking
The Secabo SH7 is shipped with a silicone mat and a cover to
protect the membrane surface. Carefully remove them from the
box.
5.) After use
After you have used the SH7, please let it cool down completely.
Then you can put the silicone mat and the protective cover back
on. Now the plate can be removed from the press.
2.) Mount
Take the SH7 out of the packaging and slide it onto the press
head. Then mount the screws as usual and tighten them.
6.) Dismount
After dismantling, make sure that the silicone mat and the pro-
tective cover are properly attached to the SH7.
7.) Storage
Before storing the SH7, check again that the silicone mat really
covers the membrane completely. This will guarantee that the
SH7 will last longer and prevent it from wearing out too quickly.
8.) Store
Now you can store the SH7 and have it ready for the next use.
3.) Remove the cover
If the SH7 has been fi tted correctly, you can now remove the
cover and the silicone mat.
4.) Connect and start
Now you can connect the cables to the press and start using
the press. Please note that the heat of the heat press must not
exceed 190° C. To be on the safe side, please stick the yellow
warning sticker on your controller. (Enclosed)
ACHTUNG! Bitte bringen Sie den beigefügten Warnhinweis-Sticker an dem Controller Ihrer Transferpresse an!
ATTENTION! Please attach the enclosed warning sticker to the controller of your heat press!
Nicht mehr als
190° C aufheizen
Do not heat more
than to 190° C
SH7 Softheat
!!
Overview of individual parts and article numbers
This product consists of 4 packing units
Hier haben wir das ganze Handling
vom Auspacken bis zum Aufbau
für Sie noch als Video visualisiert.
Falls Sie noch Fragen haben, mel-
den Sie sich jederzeit gerne per E-
Mail an [email protected].
Here we have visualised the entire
handling from unpacking to as-
sembly for you as a video. If you
have any questions, please do not
hesitate to contact us by e-mail at
[email protected].
ME
SCAN
Item Qty. Description-EN Secabo PN
1 1 Packaging Unit Work & Storage Area
Secabo Shelving Table 16s with packaging
183.10015.00
1.1 1 Work Surface Secabo Shelving Tabel 16s 990.183.002.01
1.2 1 Storage Area Secabo Shelving Table 16s 990.183.003.01
2 1 Packing unit frame and small parts Secabo shelving table 16 183.20001.00
2.1 5 Packaging unit pipe set 625 mm with packaging 183.10007.00
2.1.1 2 28s Pipe-625 mm 990.183.006.01
2.2 1 Packaging unit t-connector with packaging 183.10005.00
2.2.1 2 T-connector 990.183.008.01
2.3 1 Packaging unit pipe set 780 mm with packaging 183.10009.00
2.3.1 4 28s Pipe-780 mm 990.183.009.01
2.4 3 Packaging unit pipe holder with packaging 183.10011.00
2.4.1 4 Pipe holder clamp 990.183.018.01
2.5 1 Packaging unit vertical connector 90° with packaging 183.10003.00
2.5.1 8 Vertical connector 90° 990.183.024.01
2.6 3 Packaging unit pan head screw 4.5 x 13mm RW20 with packaging 183.10013.00
2.6.1 8 Pan head screw 4.5 x 13mm RW20 990.183.026.01
2.7 4 Packaging unit swivel castor with brake 100mm with packaging 183.10020.00
2.7.1 1 Swivel castor with brake 100mm 990.183.022.01
2.7.2 4 Washer M5 990.183.062.01
2.8 1 Packaging Unit Screwdriver 183.10069.00
2.8.1 1 Bit Handle for 1/4" Bit 990.183.082.01
2.8.2 1 4mm HSH Bit 1/4" 990.183.083.01
2.8.3 1 RW 20 (ASSY) Bit 1/4" 990.183.084.01
2.8.4 1 5mm HSH Bit 1/4" 990.183.108.01
3 1 Packaging unit secabo shelving module with packaging 183.10022.00
3.1 1 Secabo Shelving Module 990.183.0023
3.1.1 2 Secabo Shelving Modul Board 990.183.011.01
3.1.2 16 Adjusting ring DIN 705 OD 45 ID 28 T16 mm 990.183.012.01
3.1.3 9 Spacer Stud II M6x12 990.183.013.01
3.1.4 18 Screw HSBH M6x20 990.183.014.01
3.1.5 16 Headless Screw ISO 4029 M8x8 990.183.015.01
4 1 Packaging unit placement tubes Secabo module 16 183.20002.00
4.1 8 Packaging unit pipe set 625 mm with packaging 183.10007.00
4.1.1 2 28s Pipe-625 mm 990.183.006.01
4.2 8 Packaging unit pipe cap 28s diameter with packaging 183.10053.00
4.2.1 4 Pipe cap 28s diameter 990.183.028.01
1 Packaging Unit Work & Storage
Area Secabo Shelving Table 16s
with packaging
183.10015.00
2 Packing unit frame and small parts
Secabo shelving table 16
183.20001.00
3 Packaging unit secabo shelving
module with packaging
183.10022.00
4 Packaging unit placement tubes
Secabo module 16
183.20002.00
Shelving table 16
Work table 16 (77cm x 77cm x 90cm) Art.Nr.: 183.000.00
Secabo Modulares Shelving System • Secabo Modular Shelving System
QUICK GUIDE
Hier sind ein paar wichtige Hinweise die sie beim Verwenden Ihrer SH7 Softheat beachten sollten:
Here are a few important tips to keep in mind when using your SH7 Softheat:
Hier haben wir das ganze Handling mit der SH7 vom Auspacken bis zur Aufbewahrung für Sie noch als Video visualisiert.
Falls Sie noch Fragen haben melden Sie sich jederzeit gerne per E-mail an [email protected]
Here we have visualised the entire handling of the SH7 from unpacking to storage for you as a video. If you have any ques-
tions, please do not hesitate to contact us by e-mail at [email protected].
QUICK GUIDE SH7 SOFTHEAT
WWW.SECABO.COM
1.) Auspacken
Die Secabo SH7 wird mit einer Silikonmatte und einem Überzug
versendet um die Membranfläche zu schützen. Nehmen Sie diese
vorsichtig aus dem Karton.
5.) Nach Benutzung
Nachdem Sie die SH7 benutzt haben, lassen Sie diese bitte vollstän-
dig abkühlen. Danach können Sie die Silikonmatte und den Schutz-
überzug wieder anbringen. Nun kann die Platte von der Presse ab-
montiert werden.
2.) Montieren
Nehmen Sie die SH7 sowie aus der Verpackung und schieben Sie
diese an den Pressenkopf. Dann montieren Sie wie gewohnt die
Schrauben und ziehen diese fest.
6.) Ablegen
Nach der Abmontage tellen Sie sicher, dass die Silikonmatte und der
Schutzüberzug richtig an der SH7 angebracht sind.
7.) Aufbewahrung
Überprüfen Sie nochmal bevor Sie die SH7 lagern ob die Silikonmat-
te auch wirklich die Membrane komplett abdeckt. Somit garantieren
Sie auch einen längeren Erhalt der SH7 und verhindern einen zu
schnelle Abnuntzung.
8.) Lagern
Nun können Sie die SH7 ablegen und für den nächsten Einsatz
bereithalten.
3.) Überzug entfernen
Wenn die SH7 richtig angebracht wurde, können Sie nun den Üner-
zug und die Silikonmatte abziehen.
4.) Anschließen und loslegen
Nun können Sie die Kabel mit der Presse verbinden und die Presse
in Betrieb nehmen. Bitte beachten Sie, dass die Transferpresse nicht
mehr als 190° C aufheizen dürfen. Bitte kleben Sie zur Sicherheit den
gelben Warnaufkleber noch auf ihren Controller. (Liegt bei)
1.) Unpacking
The Secabo SH7 is shipped with a silicone mat and a cover to
protect the membrane surface. Carefully remove them from the
box.
5.) After use
After you have used the SH7, please let it cool down completely.
Then you can put the silicone mat and the protective cover back
on. Now the plate can be removed from the press.
2.) Mount
Take the SH7 out of the packaging and slide it onto the press
head. Then mount the screws as usual and tighten them.
6.) Dismount
After dismantling, make sure that the silicone mat and the pro-
tective cover are properly attached to the SH7.
7.) Storage
Before storing the SH7, check again that the silicone mat really
covers the membrane completely. This will guarantee that the
SH7 will last longer and prevent it from wearing out too quickly.
8.) Store
Now you can store the SH7 and have it ready for the next use.
3.) Remove the cover
If the SH7 has been fi tted correctly, you can now remove the
cover and the silicone mat.
4.) Connect and start
Now you can connect the cables to the press and start using
the press. Please note that the heat of the heat press must not
exceed 190° C. To be on the safe side, please stick the yellow
warning sticker on your controller. (Enclosed)
ACHTUNG! Bitte bringen Sie den beigefügten Warnhinweis-Sticker an dem Controller Ihrer Transferpresse an!
ATTENTION! Please attach the enclosed warning sticker to the controller of your heat press!
Nicht mehr als
190° C aufheizen
Do not heat more
than to 190° C
SH7 Softheat
!!
Hier haben wir das ganze Handling vom Auspacken bis zum Aufbau für Sie noch als Video visualisiert.
Falls Sie noch Fragen haben, melden Sie sich jederzeit gerne per E-Mail an [email protected].
Here we have visualised the entire handling from unpacking to assembly for you as a video.
If you have any questions, please do not hesitate to contact us by e-mail at [email protected].
Der Einfachheit halber kann dieser Schritt auf der Ablagefläche mit der Artikelnummer 990.183.003.01 durchgeführt werden.
For simplicity, this step can be carried out on the storage area plate with item number 990.183.003.01.
1
2
Hier sind ein paar wichtige Hinweise die sie beim Verwenden Ihrer SH7 Softheat beachten sollten:
Here are a few important tips to keep in mind when using your SH7 Softheat:
Hier haben wir das ganze Handling mit der SH7 vom Auspacken bis zur Aufbewahrung für Sie noch als Video visualisiert.
Falls Sie noch Fragen haben melden Sie sich jederzeit gerne per E-mail an [email protected]
Here we have visualised the entire handling of the SH7 from unpacking to storage for you as a video. If you have any ques-
tions, please do not hesitate to contact us by e-mail at [email protected].
QUICK GUIDE SH7 SOFTHEAT
WWW.SECABO.COM
1.) Auspacken
Die Secabo SH7 wird mit einer Silikonmatte und einem Überzug
versendet um die Membranfläche zu schützen. Nehmen Sie diese
vorsichtig aus dem Karton.
5.) Nach Benutzung
Nachdem Sie die SH7 benutzt haben, lassen Sie diese bitte vollstän-
dig abkühlen. Danach können Sie die Silikonmatte und den Schutz-
überzug wieder anbringen. Nun kann die Platte von der Presse ab-
montiert werden.
2.) Montieren
Nehmen Sie die SH7 sowie aus der Verpackung und schieben Sie
diese an den Pressenkopf. Dann montieren Sie wie gewohnt die
Schrauben und ziehen diese fest.
6.) Ablegen
Nach der Abmontage tellen Sie sicher, dass die Silikonmatte und der
Schutzüberzug richtig an der SH7 angebracht sind.
7.) Aufbewahrung
Überprüfen Sie nochmal bevor Sie die SH7 lagern ob die Silikonmat-
te auch wirklich die Membrane komplett abdeckt. Somit garantieren
Sie auch einen längeren Erhalt der SH7 und verhindern einen zu
schnelle Abnuntzung.
8.) Lagern
Nun können Sie die SH7 ablegen und für den nächsten Einsatz
bereithalten.
3.) Überzug entfernen
Wenn die SH7 richtig angebracht wurde, können Sie nun den Üner-
zug und die Silikonmatte abziehen.
4.) Anschließen und loslegen
Nun können Sie die Kabel mit der Presse verbinden und die Presse
in Betrieb nehmen. Bitte beachten Sie, dass die Transferpresse nicht
mehr als 190° C aufheizen dürfen. Bitte kleben Sie zur Sicherheit den
gelben Warnaufkleber noch auf ihren Controller. (Liegt bei)
1.) Unpacking
The Secabo SH7 is shipped with a silicone mat and a cover to
protect the membrane surface. Carefully remove them from the
box.
5.) After use
After you have used the SH7, please let it cool down completely.
Then you can put the silicone mat and the protective cover back
on. Now the plate can be removed from the press.
2.) Mount
Take the SH7 out of the packaging and slide it onto the press
head. Then mount the screws as usual and tighten them.
6.) Dismount
After dismantling, make sure that the silicone mat and the pro-
tective cover are properly attached to the SH7.
7.) Storage
Before storing the SH7, check again that the silicone mat really
covers the membrane completely. This will guarantee that the
SH7 will last longer and prevent it from wearing out too quickly.
8.) Store
Now you can store the SH7 and have it ready for the next use.
3.) Remove the cover
If the SH7 has been fi tted correctly, you can now remove the
cover and the silicone mat.
4.) Connect and start
Now you can connect the cables to the press and start using
the press. Please note that the heat of the heat press must not
exceed 190° C. To be on the safe side, please stick the yellow
warning sticker on your controller. (Enclosed)
ACHTUNG! Bitte bringen Sie den beigefügten Warnhinweis-Sticker an dem Controller Ihrer Transferpresse an!
ATTENTION! Please attach the enclosed warning sticker to the controller of your heat press!
Nicht mehr als
190° C aufheizen
Do not heat more
than to 190° C
SH7 Softheat
!!
Shelving table 16
Work table 16 (77cm x 77cm x 90cm) Art.Nr.: 183.000.00
Secabo Modulares Shelving System • Secabo Modular Shelving System
QUICK GUIDE
Hier sind ein paar wichtige Hinweise die sie beim Verwenden Ihrer SH7 Softheat beachten sollten:
Here are a few important tips to keep in mind when using your SH7 Softheat:
Hier haben wir das ganze Handling mit der SH7 vom Auspacken bis zur Aufbewahrung für Sie noch als Video visualisiert.
Falls Sie noch Fragen haben melden Sie sich jederzeit gerne per E-mail an [email protected]
Here we have visualised the entire handling of the SH7 from unpacking to storage for you as a video. If you have any ques-
tions, please do not hesitate to contact us by e-mail at [email protected].
QUICK GUIDE SH7 SOFTHEAT
WWW.SECABO.COM
1.) Auspacken
Die Secabo SH7 wird mit einer Silikonmatte und einem Überzug
versendet um die Membranfläche zu schützen. Nehmen Sie diese
vorsichtig aus dem Karton.
5.) Nach Benutzung
Nachdem Sie die SH7 benutzt haben, lassen Sie diese bitte vollstän-
dig abkühlen. Danach können Sie die Silikonmatte und den Schutz-
überzug wieder anbringen. Nun kann die Platte von der Presse ab-
montiert werden.
2.) Montieren
Nehmen Sie die SH7 sowie aus der Verpackung und schieben Sie
diese an den Pressenkopf. Dann montieren Sie wie gewohnt die
Schrauben und ziehen diese fest.
6.) Ablegen
Nach der Abmontage tellen Sie sicher, dass die Silikonmatte und der
Schutzüberzug richtig an der SH7 angebracht sind.
7.) Aufbewahrung
Überprüfen Sie nochmal bevor Sie die SH7 lagern ob die Silikonmat-
te auch wirklich die Membrane komplett abdeckt. Somit garantieren
Sie auch einen längeren Erhalt der SH7 und verhindern einen zu
schnelle Abnuntzung.
8.) Lagern
Nun können Sie die SH7 ablegen und für den nächsten Einsatz
bereithalten.
3.) Überzug entfernen
Wenn die SH7 richtig angebracht wurde, können Sie nun den Üner-
zug und die Silikonmatte abziehen.
4.) Anschließen und loslegen
Nun können Sie die Kabel mit der Presse verbinden und die Presse
in Betrieb nehmen. Bitte beachten Sie, dass die Transferpresse nicht
mehr als 190° C aufheizen dürfen. Bitte kleben Sie zur Sicherheit den
gelben Warnaufkleber noch auf ihren Controller. (Liegt bei)
1.) Unpacking
The Secabo SH7 is shipped with a silicone mat and a cover to
protect the membrane surface. Carefully remove them from the
box.
5.) After use
After you have used the SH7, please let it cool down completely.
Then you can put the silicone mat and the protective cover back
on. Now the plate can be removed from the press.
2.) Mount
Take the SH7 out of the packaging and slide it onto the press
head. Then mount the screws as usual and tighten them.
6.) Dismount
After dismantling, make sure that the silicone mat and the pro-
tective cover are properly attached to the SH7.
7.) Storage
Before storing the SH7, check again that the silicone mat really
covers the membrane completely. This will guarantee that the
SH7 will last longer and prevent it from wearing out too quickly.
8.) Store
Now you can store the SH7 and have it ready for the next use.
3.) Remove the cover
If the SH7 has been fi tted correctly, you can now remove the
cover and the silicone mat.
4.) Connect and start
Now you can connect the cables to the press and start using
the press. Please note that the heat of the heat press must not
exceed 190° C. To be on the safe side, please stick the yellow
warning sticker on your controller. (Enclosed)
ACHTUNG! Bitte bringen Sie den beigefügten Warnhinweis-Sticker an dem Controller Ihrer Transferpresse an!
ATTENTION! Please attach the enclosed warning sticker to the controller of your heat press!
Nicht mehr als
190° C aufheizen
Do not heat more
than to 190° C
SH7 Softheat
!!
Hier haben wir das ganze Handling vom Auspacken bis zum Aufbau für Sie noch als Video visualisiert.
Falls Sie noch Fragen haben, melden Sie sich jederzeit gerne per E-Mail an [email protected].
Here we have visualised the entire handling from unpacking to assembly for you as a video.
If you have any questions, please do not hesitate to contact us by e-mail at [email protected].
3
4
Shelving table 16
Work table 16 (77cm x 77cm x 90cm) Art.Nr.: 183.000.00
Secabo Modulares Shelving System • Secabo Modular Shelving System
QUICK GUIDE
Hier sind ein paar wichtige Hinweise die sie beim Verwenden Ihrer SH7 Softheat beachten sollten:
Here are a few important tips to keep in mind when using your SH7 Softheat:
Hier haben wir das ganze Handling mit der SH7 vom Auspacken bis zur Aufbewahrung für Sie noch als Video visualisiert.
Falls Sie noch Fragen haben melden Sie sich jederzeit gerne per E-mail an [email protected]
Here we have visualised the entire handling of the SH7 from unpacking to storage for you as a video. If you have any ques-
tions, please do not hesitate to contact us by e-mail at [email protected].
QUICK GUIDE SH7 SOFTHEAT
WWW.SECABO.COM
1.) Auspacken
Die Secabo SH7 wird mit einer Silikonmatte und einem Überzug
versendet um die Membranfläche zu schützen. Nehmen Sie diese
vorsichtig aus dem Karton.
5.) Nach Benutzung
Nachdem Sie die SH7 benutzt haben, lassen Sie diese bitte vollstän-
dig abkühlen. Danach können Sie die Silikonmatte und den Schutz-
überzug wieder anbringen. Nun kann die Platte von der Presse ab-
montiert werden.
2.) Montieren
Nehmen Sie die SH7 sowie aus der Verpackung und schieben Sie
diese an den Pressenkopf. Dann montieren Sie wie gewohnt die
Schrauben und ziehen diese fest.
6.) Ablegen
Nach der Abmontage tellen Sie sicher, dass die Silikonmatte und der
Schutzüberzug richtig an der SH7 angebracht sind.
7.) Aufbewahrung
Überprüfen Sie nochmal bevor Sie die SH7 lagern ob die Silikonmat-
te auch wirklich die Membrane komplett abdeckt. Somit garantieren
Sie auch einen längeren Erhalt der SH7 und verhindern einen zu
schnelle Abnuntzung.
8.) Lagern
Nun können Sie die SH7 ablegen und für den nächsten Einsatz
bereithalten.
3.) Überzug entfernen
Wenn die SH7 richtig angebracht wurde, können Sie nun den Üner-
zug und die Silikonmatte abziehen.
4.) Anschließen und loslegen
Nun können Sie die Kabel mit der Presse verbinden und die Presse
in Betrieb nehmen. Bitte beachten Sie, dass die Transferpresse nicht
mehr als 190° C aufheizen dürfen. Bitte kleben Sie zur Sicherheit den
gelben Warnaufkleber noch auf ihren Controller. (Liegt bei)
1.) Unpacking
The Secabo SH7 is shipped with a silicone mat and a cover to
protect the membrane surface. Carefully remove them from the
box.
5.) After use
After you have used the SH7, please let it cool down completely.
Then you can put the silicone mat and the protective cover back
on. Now the plate can be removed from the press.
2.) Mount
Take the SH7 out of the packaging and slide it onto the press
head. Then mount the screws as usual and tighten them.
6.) Dismount
After dismantling, make sure that the silicone mat and the pro-
tective cover are properly attached to the SH7.
7.) Storage
Before storing the SH7, check again that the silicone mat really
covers the membrane completely. This will guarantee that the
SH7 will last longer and prevent it from wearing out too quickly.
8.) Store
Now you can store the SH7 and have it ready for the next use.
3.) Remove the cover
If the SH7 has been fi tted correctly, you can now remove the
cover and the silicone mat.
4.) Connect and start
Now you can connect the cables to the press and start using
the press. Please note that the heat of the heat press must not
exceed 190° C. To be on the safe side, please stick the yellow
warning sticker on your controller. (Enclosed)
ACHTUNG! Bitte bringen Sie den beigefügten Warnhinweis-Sticker an dem Controller Ihrer Transferpresse an!
ATTENTION! Please attach the enclosed warning sticker to the controller of your heat press!
Nicht mehr als
190° C aufheizen
Do not heat more
than to 190° C
SH7 Softheat
!!
Hier haben wir das ganze Handling vom Auspacken bis zum Aufbau für Sie noch als Video visualisiert.
Falls Sie noch Fragen haben, melden Sie sich jederzeit gerne per E-Mail an [email protected].
Here we have visualised the entire handling from unpacking to assembly for you as a video.
If you have any questions, please do not hesitate to contact us by e-mail at [email protected].
5
6
Bitte benutzen Sie beim Arbeiten die Bremse der Lenkrollen.
Please use the brake on the castors when working.
Hier sind ein paar wichtige Hinweise die sie beim Verwenden Ihrer SH7 Softheat beachten sollten:
Here are a few important tips to keep in mind when using your SH7 Softheat:
Hier haben wir das ganze Handling mit der SH7 vom Auspacken bis zur Aufbewahrung für Sie noch als Video visualisiert.
Falls Sie noch Fragen haben melden Sie sich jederzeit gerne per E-mail an [email protected]
Here we have visualised the entire handling of the SH7 from unpacking to storage for you as a video. If you have any ques-
tions, please do not hesitate to contact us by e-mail at [email protected].
QUICK GUIDE SH7 SOFTHEAT
WWW.SECABO.COM
1.) Auspacken
Die Secabo SH7 wird mit einer Silikonmatte und einem Überzug
versendet um die Membranfläche zu schützen. Nehmen Sie diese
vorsichtig aus dem Karton.
5.) Nach Benutzung
Nachdem Sie die SH7 benutzt haben, lassen Sie diese bitte vollstän-
dig abkühlen. Danach können Sie die Silikonmatte und den Schutz-
überzug wieder anbringen. Nun kann die Platte von der Presse ab-
montiert werden.
2.) Montieren
Nehmen Sie die SH7 sowie aus der Verpackung und schieben Sie
diese an den Pressenkopf. Dann montieren Sie wie gewohnt die
Schrauben und ziehen diese fest.
6.) Ablegen
Nach der Abmontage tellen Sie sicher, dass die Silikonmatte und der
Schutzüberzug richtig an der SH7 angebracht sind.
7.) Aufbewahrung
Überprüfen Sie nochmal bevor Sie die SH7 lagern ob die Silikonmat-
te auch wirklich die Membrane komplett abdeckt. Somit garantieren
Sie auch einen längeren Erhalt der SH7 und verhindern einen zu
schnelle Abnuntzung.
8.) Lagern
Nun können Sie die SH7 ablegen und für den nächsten Einsatz
bereithalten.
3.) Überzug entfernen
Wenn die SH7 richtig angebracht wurde, können Sie nun den Üner-
zug und die Silikonmatte abziehen.
4.) Anschließen und loslegen
Nun können Sie die Kabel mit der Presse verbinden und die Presse
in Betrieb nehmen. Bitte beachten Sie, dass die Transferpresse nicht
mehr als 190° C aufheizen dürfen. Bitte kleben Sie zur Sicherheit den
gelben Warnaufkleber noch auf ihren Controller. (Liegt bei)
1.) Unpacking
The Secabo SH7 is shipped with a silicone mat and a cover to
protect the membrane surface. Carefully remove them from the
box.
5.) After use
After you have used the SH7, please let it cool down completely.
Then you can put the silicone mat and the protective cover back
on. Now the plate can be removed from the press.
2.) Mount
Take the SH7 out of the packaging and slide it onto the press
head. Then mount the screws as usual and tighten them.
6.) Dismount
After dismantling, make sure that the silicone mat and the pro-
tective cover are properly attached to the SH7.
7.) Storage
Before storing the SH7, check again that the silicone mat really
covers the membrane completely. This will guarantee that the
SH7 will last longer and prevent it from wearing out too quickly.
8.) Store
Now you can store the SH7 and have it ready for the next use.
3.) Remove the cover
If the SH7 has been fi tted correctly, you can now remove the
cover and the silicone mat.
4.) Connect and start
Now you can connect the cables to the press and start using
the press. Please note that the heat of the heat press must not
exceed 190° C. To be on the safe side, please stick the yellow
warning sticker on your controller. (Enclosed)
ACHTUNG! Bitte bringen Sie den beigefügten Warnhinweis-Sticker an dem Controller Ihrer Transferpresse an!
ATTENTION! Please attach the enclosed warning sticker to the controller of your heat press!
Nicht mehr als
190° C aufheizen
Do not heat more
than to 190° C
SH7 Softheat
!!
Shelving table 16
Work table 16 (77cm x 77cm x 90cm) Art.Nr.: 183.000.00
Secabo Modulares Shelving System • Secabo Modular Shelving System
QUICK GUIDE
Hier sind ein paar wichtige Hinweise die sie beim Verwenden Ihrer SH7 Softheat beachten sollten:
Here are a few important tips to keep in mind when using your SH7 Softheat:
Hier haben wir das ganze Handling mit der SH7 vom Auspacken bis zur Aufbewahrung für Sie noch als Video visualisiert.
Falls Sie noch Fragen haben melden Sie sich jederzeit gerne per E-mail an [email protected]
Here we have visualised the entire handling of the SH7 from unpacking to storage for you as a video. If you have any ques-
tions, please do not hesitate to contact us by e-mail at [email protected].
QUICK GUIDE SH7 SOFTHEAT
WWW.SECABO.COM
1.) Auspacken
Die Secabo SH7 wird mit einer Silikonmatte und einem Überzug
versendet um die Membranfläche zu schützen. Nehmen Sie diese
vorsichtig aus dem Karton.
5.) Nach Benutzung
Nachdem Sie die SH7 benutzt haben, lassen Sie diese bitte vollstän-
dig abkühlen. Danach können Sie die Silikonmatte und den Schutz-
überzug wieder anbringen. Nun kann die Platte von der Presse ab-
montiert werden.
2.) Montieren
Nehmen Sie die SH7 sowie aus der Verpackung und schieben Sie
diese an den Pressenkopf. Dann montieren Sie wie gewohnt die
Schrauben und ziehen diese fest.
6.) Ablegen
Nach der Abmontage tellen Sie sicher, dass die Silikonmatte und der
Schutzüberzug richtig an der SH7 angebracht sind.
7.) Aufbewahrung
Überprüfen Sie nochmal bevor Sie die SH7 lagern ob die Silikonmat-
te auch wirklich die Membrane komplett abdeckt. Somit garantieren
Sie auch einen längeren Erhalt der SH7 und verhindern einen zu
schnelle Abnuntzung.
8.) Lagern
Nun können Sie die SH7 ablegen und für den nächsten Einsatz
bereithalten.
3.) Überzug entfernen
Wenn die SH7 richtig angebracht wurde, können Sie nun den Üner-
zug und die Silikonmatte abziehen.
4.) Anschließen und loslegen
Nun können Sie die Kabel mit der Presse verbinden und die Presse
in Betrieb nehmen. Bitte beachten Sie, dass die Transferpresse nicht
mehr als 190° C aufheizen dürfen. Bitte kleben Sie zur Sicherheit den
gelben Warnaufkleber noch auf ihren Controller. (Liegt bei)
1.) Unpacking
The Secabo SH7 is shipped with a silicone mat and a cover to
protect the membrane surface. Carefully remove them from the
box.
5.) After use
After you have used the SH7, please let it cool down completely.
Then you can put the silicone mat and the protective cover back
on. Now the plate can be removed from the press.
2.) Mount
Take the SH7 out of the packaging and slide it onto the press
head. Then mount the screws as usual and tighten them.
6.) Dismount
After dismantling, make sure that the silicone mat and the pro-
tective cover are properly attached to the SH7.
7.) Storage
Before storing the SH7, check again that the silicone mat really
covers the membrane completely. This will guarantee that the
SH7 will last longer and prevent it from wearing out too quickly.
8.) Store
Now you can store the SH7 and have it ready for the next use.
3.) Remove the cover
If the SH7 has been fi tted correctly, you can now remove the
cover and the silicone mat.
4.) Connect and start
Now you can connect the cables to the press and start using
the press. Please note that the heat of the heat press must not
exceed 190° C. To be on the safe side, please stick the yellow
warning sticker on your controller. (Enclosed)
ACHTUNG! Bitte bringen Sie den beigefügten Warnhinweis-Sticker an dem Controller Ihrer Transferpresse an!
ATTENTION! Please attach the enclosed warning sticker to the controller of your heat press!
Nicht mehr als
190° C aufheizen
Do not heat more
than to 190° C
SH7 Softheat
!!
Hier haben wir das ganze Handling vom Auspacken bis zum Aufbau für Sie noch als Video visualisiert.
Falls Sie noch Fragen haben, melden Sie sich jederzeit gerne per E-Mail an [email protected].
Here we have visualised the entire handling from unpacking to assembly for you as a video.
If you have any questions, please do not hesitate to contact us by e-mail at [email protected].
Mit dem modularen System können Sie
Ihre Tische nach Belieben aufbauen, so
dass Sie auch die hintere Mittelstange zur
Befestigung des Moduls weiter nach oben
stellen können (siehe farbige Fotos auf der
ersten Seite). Dazu müssen Sie die Rohr-
halterungen, die in der Mitte nach oben
ausgerichteten sind, um eine Reihe nach
oben versetzten.
With the modular system, you can build
up your tables as you like, so you can also
move the rear centre pipe for attaching the
module further up (see coloured photos
on the fi rst page). To do this, you need to
move the tube holders aligned in the midd-
le upwards by one row.
7 8
9
Drawer Shelving System
Secabo Modulares Shelving System • Secabo Modular Shelving System
QUICK GUIDE
Hier sind ein paar wichtige Hinweise die sie beim Verwenden Ihrer SH7 Softheat beachten sollten:
Here are a few important tips to keep in mind when using your SH7 Softheat:
Hier haben wir das ganze Handling mit der SH7 vom Auspacken bis zur Aufbewahrung für Sie noch als Video visualisiert.
Falls Sie noch Fragen haben melden Sie sich jederzeit gerne per E-mail an [email protected]
Here we have visualised the entire handling of the SH7 from unpacking to storage for you as a video. If you have any ques-
tions, please do not hesitate to contact us by e-mail at [email protected].
QUICK GUIDE SH7 SOFTHEAT
WWW.SECABO.COM
1.) Auspacken
Die Secabo SH7 wird mit einer Silikonmatte und einem Überzug
versendet um die Membranfläche zu schützen. Nehmen Sie diese
vorsichtig aus dem Karton.
5.) Nach Benutzung
Nachdem Sie die SH7 benutzt haben, lassen Sie diese bitte vollstän-
dig abkühlen. Danach können Sie die Silikonmatte und den Schutz-
überzug wieder anbringen. Nun kann die Platte von der Presse ab-
montiert werden.
2.) Montieren
Nehmen Sie die SH7 sowie aus der Verpackung und schieben Sie
diese an den Pressenkopf. Dann montieren Sie wie gewohnt die
Schrauben und ziehen diese fest.
6.) Ablegen
Nach der Abmontage tellen Sie sicher, dass die Silikonmatte und der
Schutzüberzug richtig an der SH7 angebracht sind.
7.) Aufbewahrung
Überprüfen Sie nochmal bevor Sie die SH7 lagern ob die Silikonmat-
te auch wirklich die Membrane komplett abdeckt. Somit garantieren
Sie auch einen längeren Erhalt der SH7 und verhindern einen zu
schnelle Abnuntzung.
8.) Lagern
Nun können Sie die SH7 ablegen und für den nächsten Einsatz
bereithalten.
3.) Überzug entfernen
Wenn die SH7 richtig angebracht wurde, können Sie nun den Üner-
zug und die Silikonmatte abziehen.
4.) Anschließen und loslegen
Nun können Sie die Kabel mit der Presse verbinden und die Presse
in Betrieb nehmen. Bitte beachten Sie, dass die Transferpresse nicht
mehr als 190° C aufheizen dürfen. Bitte kleben Sie zur Sicherheit den
gelben Warnaufkleber noch auf ihren Controller. (Liegt bei)
1.) Unpacking
The Secabo SH7 is shipped with a silicone mat and a cover to
protect the membrane surface. Carefully remove them from the
box.
5.) After use
After you have used the SH7, please let it cool down completely.
Then you can put the silicone mat and the protective cover back
on. Now the plate can be removed from the press.
2.) Mount
Take the SH7 out of the packaging and slide it onto the press
head. Then mount the screws as usual and tighten them.
6.) Dismount
After dismantling, make sure that the silicone mat and the pro-
tective cover are properly attached to the SH7.
7.) Storage
Before storing the SH7, check again that the silicone mat really
covers the membrane completely. This will guarantee that the
SH7 will last longer and prevent it from wearing out too quickly.
8.) Store
Now you can store the SH7 and have it ready for the next use.
3.) Remove the cover
If the SH7 has been fi tted correctly, you can now remove the
cover and the silicone mat.
4.) Connect and start
Now you can connect the cables to the press and start using
the press. Please note that the heat of the heat press must not
exceed 190° C. To be on the safe side, please stick the yellow
warning sticker on your controller. (Enclosed)
ACHTUNG! Bitte bringen Sie den beigefügten Warnhinweis-Sticker an dem Controller Ihrer Transferpresse an!
ATTENTION! Please attach the enclosed warning sticker to the controller of your heat press!
Nicht mehr als
190° C aufheizen
Do not heat more
than to 190° C
SH7 Softheat
!!
Hier haben wir das ganze Handling vom Auspacken bis zum Aufbau für Sie noch als Video visualisiert.
Falls Sie noch Fragen haben, melden Sie sich jederzeit gerne per E-Mail an [email protected].
Here we have visualised the entire handling from unpacking to assembly for you as a video.
If you have any questions, please do not hesitate to contact us by e-mail at [email protected].
Art.Nr.: 183.000.09
1
2 3
Anz. Description-EN Secabo PN
2 Mounting Bracket Drawer 990.183.088.01
4 Nut HN M4 990.183.090.01
4 Screw HSBH M4x10 990.183.091.01
1 Bit Handle for 1/4" Bit 990.183.082.01
1 4mm HSH Bit 1/4" 990.183.083.01
Hier sind ein paar wichtige Hinweise die sie beim Verwenden Ihrer SH7 Softheat beachten sollten:
Here are a few important tips to keep in mind when using your SH7 Softheat:
Hier haben wir das ganze Handling mit der SH7 vom Auspacken bis zur Aufbewahrung für Sie noch als Video visualisiert.
Falls Sie noch Fragen haben melden Sie sich jederzeit gerne per E-mail an [email protected]
Here we have visualised the entire handling of the SH7 from unpacking to storage for you as a video. If you have any ques-
tions, please do not hesitate to contact us by e-mail at [email protected].
QUICK GUIDE SH7 SOFTHEAT
WWW.SECABO.COM
1.) Auspacken
Die Secabo SH7 wird mit einer Silikonmatte und einem Überzug
versendet um die Membranfläche zu schützen. Nehmen Sie diese
vorsichtig aus dem Karton.
5.) Nach Benutzung
Nachdem Sie die SH7 benutzt haben, lassen Sie diese bitte vollstän-
dig abkühlen. Danach können Sie die Silikonmatte und den Schutz-
überzug wieder anbringen. Nun kann die Platte von der Presse ab-
montiert werden.
2.) Montieren
Nehmen Sie die SH7 sowie aus der Verpackung und schieben Sie
diese an den Pressenkopf. Dann montieren Sie wie gewohnt die
Schrauben und ziehen diese fest.
6.) Ablegen
Nach der Abmontage tellen Sie sicher, dass die Silikonmatte und der
Schutzüberzug richtig an der SH7 angebracht sind.
7.) Aufbewahrung
Überprüfen Sie nochmal bevor Sie die SH7 lagern ob die Silikonmat-
te auch wirklich die Membrane komplett abdeckt. Somit garantieren
Sie auch einen längeren Erhalt der SH7 und verhindern einen zu
schnelle Abnuntzung.
8.) Lagern
Nun können Sie die SH7 ablegen und für den nächsten Einsatz
bereithalten.
3.) Überzug entfernen
Wenn die SH7 richtig angebracht wurde, können Sie nun den Üner-
zug und die Silikonmatte abziehen.
4.) Anschließen und loslegen
Nun können Sie die Kabel mit der Presse verbinden und die Presse
in Betrieb nehmen. Bitte beachten Sie, dass die Transferpresse nicht
mehr als 190° C aufheizen dürfen. Bitte kleben Sie zur Sicherheit den
gelben Warnaufkleber noch auf ihren Controller. (Liegt bei)
1.) Unpacking
The Secabo SH7 is shipped with a silicone mat and a cover to
protect the membrane surface. Carefully remove them from the
box.
5.) After use
After you have used the SH7, please let it cool down completely.
Then you can put the silicone mat and the protective cover back
on. Now the plate can be removed from the press.
2.) Mount
Take the SH7 out of the packaging and slide it onto the press
head. Then mount the screws as usual and tighten them.
6.) Dismount
After dismantling, make sure that the silicone mat and the pro-
tective cover are properly attached to the SH7.
7.) Storage
Before storing the SH7, check again that the silicone mat really
covers the membrane completely. This will guarantee that the
SH7 will last longer and prevent it from wearing out too quickly.
8.) Store
Now you can store the SH7 and have it ready for the next use.
3.) Remove the cover
If the SH7 has been fi tted correctly, you can now remove the
cover and the silicone mat.
4.) Connect and start
Now you can connect the cables to the press and start using
the press. Please note that the heat of the heat press must not
exceed 190° C. To be on the safe side, please stick the yellow
warning sticker on your controller. (Enclosed)
ACHTUNG! Bitte bringen Sie den beigefügten Warnhinweis-Sticker an dem Controller Ihrer Transferpresse an!
ATTENTION! Please attach the enclosed warning sticker to the controller of your heat press!
Nicht mehr als
190° C aufheizen
Do not heat more
than to 190° C
SH7 Softheat
!!
Shelving roll holder Art.Nr.: 183.10077.00
Secabo Modulares Shelving System • Secabo Modular Shelving System
QUICK GUIDE
Hier sind ein paar wichtige Hinweise die sie beim Verwenden Ihrer SH7 Softheat beachten sollten:
Here are a few important tips to keep in mind when using your SH7 Softheat:
Hier haben wir das ganze Handling mit der SH7 vom Auspacken bis zur Aufbewahrung für Sie noch als Video visualisiert.
Falls Sie noch Fragen haben melden Sie sich jederzeit gerne per E-mail an [email protected]
Here we have visualised the entire handling of the SH7 from unpacking to storage for you as a video. If you have any ques-
tions, please do not hesitate to contact us by e-mail at [email protected].
QUICK GUIDE SH7 SOFTHEAT
WWW.SECABO.COM
1.) Auspacken
Die Secabo SH7 wird mit einer Silikonmatte und einem Überzug
versendet um die Membranfläche zu schützen. Nehmen Sie diese
vorsichtig aus dem Karton.
5.) Nach Benutzung
Nachdem Sie die SH7 benutzt haben, lassen Sie diese bitte vollstän-
dig abkühlen. Danach können Sie die Silikonmatte und den Schutz-
überzug wieder anbringen. Nun kann die Platte von der Presse ab-
montiert werden.
2.) Montieren
Nehmen Sie die SH7 sowie aus der Verpackung und schieben Sie
diese an den Pressenkopf. Dann montieren Sie wie gewohnt die
Schrauben und ziehen diese fest.
6.) Ablegen
Nach der Abmontage tellen Sie sicher, dass die Silikonmatte und der
Schutzüberzug richtig an der SH7 angebracht sind.
7.) Aufbewahrung
Überprüfen Sie nochmal bevor Sie die SH7 lagern ob die Silikonmat-
te auch wirklich die Membrane komplett abdeckt. Somit garantieren
Sie auch einen längeren Erhalt der SH7 und verhindern einen zu
schnelle Abnuntzung.
8.) Lagern
Nun können Sie die SH7 ablegen und für den nächsten Einsatz
bereithalten.
3.) Überzug entfernen
Wenn die SH7 richtig angebracht wurde, können Sie nun den Üner-
zug und die Silikonmatte abziehen.
4.) Anschließen und loslegen
Nun können Sie die Kabel mit der Presse verbinden und die Presse
in Betrieb nehmen. Bitte beachten Sie, dass die Transferpresse nicht
mehr als 190° C aufheizen dürfen. Bitte kleben Sie zur Sicherheit den
gelben Warnaufkleber noch auf ihren Controller. (Liegt bei)
1.) Unpacking
The Secabo SH7 is shipped with a silicone mat and a cover to
protect the membrane surface. Carefully remove them from the
box.
5.) After use
After you have used the SH7, please let it cool down completely.
Then you can put the silicone mat and the protective cover back
on. Now the plate can be removed from the press.
2.) Mount
Take the SH7 out of the packaging and slide it onto the press
head. Then mount the screws as usual and tighten them.
6.) Dismount
After dismantling, make sure that the silicone mat and the pro-
tective cover are properly attached to the SH7.
7.) Storage
Before storing the SH7, check again that the silicone mat really
covers the membrane completely. This will guarantee that the
SH7 will last longer and prevent it from wearing out too quickly.
8.) Store
Now you can store the SH7 and have it ready for the next use.
3.) Remove the cover
If the SH7 has been fi tted correctly, you can now remove the
cover and the silicone mat.
4.) Connect and start
Now you can connect the cables to the press and start using
the press. Please note that the heat of the heat press must not
exceed 190° C. To be on the safe side, please stick the yellow
warning sticker on your controller. (Enclosed)
ACHTUNG! Bitte bringen Sie den beigefügten Warnhinweis-Sticker an dem Controller Ihrer Transferpresse an!
ATTENTION! Please attach the enclosed warning sticker to the controller of your heat press!
Nicht mehr als
190° C aufheizen
Do not heat more
than to 190° C
SH7 Softheat
!!
Hier haben wir das ganze Handling vom Auspacken bis zum Aufbau für Sie noch als Video visualisiert.
Falls Sie noch Fragen haben, melden Sie sich jederzeit gerne per E-Mail an [email protected].
Here we have visualised the entire handling from unpacking to assembly for you as a video.
If you have any questions, please do not hesitate to contact us by e-mail at [email protected].
1
3
Shelving dispenser for application tapes
Work table 16 (77cm x 77cm x 90cm) Art.Nr.: 182.030.00
Secabo Modulares Shelving System • Secabo Modular Shelving System
QUICK GUIDE
Hier sind ein paar wichtige Hinweise die sie beim Verwenden Ihrer SH7 Softheat beachten sollten:
Here are a few important tips to keep in mind when using your SH7 Softheat:
Hier haben wir das ganze Handling mit der SH7 vom Auspacken bis zur Aufbewahrung für Sie noch als Video visualisiert.
Falls Sie noch Fragen haben melden Sie sich jederzeit gerne per E-mail an [email protected]
Here we have visualised the entire handling of the SH7 from unpacking to storage for you as a video. If you have any ques-
tions, please do not hesitate to contact us by e-mail at [email protected].
QUICK GUIDE SH7 SOFTHEAT
WWW.SECABO.COM
1.) Auspacken
Die Secabo SH7 wird mit einer Silikonmatte und einem Überzug
versendet um die Membranfläche zu schützen. Nehmen Sie diese
vorsichtig aus dem Karton.
5.) Nach Benutzung
Nachdem Sie die SH7 benutzt haben, lassen Sie diese bitte vollstän-
dig abkühlen. Danach können Sie die Silikonmatte und den Schutz-
überzug wieder anbringen. Nun kann die Platte von der Presse ab-
montiert werden.
2.) Montieren
Nehmen Sie die SH7 sowie aus der Verpackung und schieben Sie
diese an den Pressenkopf. Dann montieren Sie wie gewohnt die
Schrauben und ziehen diese fest.
6.) Ablegen
Nach der Abmontage tellen Sie sicher, dass die Silikonmatte und der
Schutzüberzug richtig an der SH7 angebracht sind.
7.) Aufbewahrung
Überprüfen Sie nochmal bevor Sie die SH7 lagern ob die Silikonmat-
te auch wirklich die Membrane komplett abdeckt. Somit garantieren
Sie auch einen längeren Erhalt der SH7 und verhindern einen zu
schnelle Abnuntzung.
8.) Lagern
Nun können Sie die SH7 ablegen und für den nächsten Einsatz
bereithalten.
3.) Überzug entfernen
Wenn die SH7 richtig angebracht wurde, können Sie nun den Üner-
zug und die Silikonmatte abziehen.
4.) Anschließen und loslegen
Nun können Sie die Kabel mit der Presse verbinden und die Presse
in Betrieb nehmen. Bitte beachten Sie, dass die Transferpresse nicht
mehr als 190° C aufheizen dürfen. Bitte kleben Sie zur Sicherheit den
gelben Warnaufkleber noch auf ihren Controller. (Liegt bei)
1.) Unpacking
The Secabo SH7 is shipped with a silicone mat and a cover to
protect the membrane surface. Carefully remove them from the
box.
5.) After use
After you have used the SH7, please let it cool down completely.
Then you can put the silicone mat and the protective cover back
on. Now the plate can be removed from the press.
2.) Mount
Take the SH7 out of the packaging and slide it onto the press
head. Then mount the screws as usual and tighten them.
6.) Dismount
After dismantling, make sure that the silicone mat and the pro-
tective cover are properly attached to the SH7.
7.) Storage
Before storing the SH7, check again that the silicone mat really
covers the membrane completely. This will guarantee that the
SH7 will last longer and prevent it from wearing out too quickly.
8.) Store
Now you can store the SH7 and have it ready for the next use.
3.) Remove the cover
If the SH7 has been fi tted correctly, you can now remove the
cover and the silicone mat.
4.) Connect and start
Now you can connect the cables to the press and start using
the press. Please note that the heat of the heat press must not
exceed 190° C. To be on the safe side, please stick the yellow
warning sticker on your controller. (Enclosed)
ACHTUNG! Bitte bringen Sie den beigefügten Warnhinweis-Sticker an dem Controller Ihrer Transferpresse an!
ATTENTION! Please attach the enclosed warning sticker to the controller of your heat press!
Nicht mehr als
190° C aufheizen
Do not heat more
than to 190° C
SH7 Softheat
!!
Hier haben wir das ganze Handling vom Auspacken bis zum Aufbau für Sie noch als Video visualisiert.
Falls Sie noch Fragen haben, melden Sie sich jederzeit gerne per E-Mail an [email protected].
Here we have visualised the entire handling from unpacking to assembly for you as a video.
If you have any questions, please do not hesitate to contact us by e-mail at [email protected].
Hier sind ein paar wichtige Hinweise die sie beim Verwenden Ihrer SH7 Softheat beachten sollten:
Here are a few important tips to keep in mind when using your SH7 Softheat:
Hier haben wir das ganze Handling mit der SH7 vom Auspacken bis zur Aufbewahrung für Sie noch als Video visualisiert.
Falls Sie noch Fragen haben melden Sie sich jederzeit gerne per E-mail an [email protected]
Here we have visualised the entire handling of the SH7 from unpacking to storage for you as a video. If you have any ques-
tions, please do not hesitate to contact us by e-mail at [email protected].
QUICK GUIDE SH7 SOFTHEAT
WWW.SECABO.COM
1.) Auspacken
Die Secabo SH7 wird mit einer Silikonmatte und einem Überzug
versendet um die Membranfläche zu schützen. Nehmen Sie diese
vorsichtig aus dem Karton.
5.) Nach Benutzung
Nachdem Sie die SH7 benutzt haben, lassen Sie diese bitte vollstän-
dig abkühlen. Danach können Sie die Silikonmatte und den Schutz-
überzug wieder anbringen. Nun kann die Platte von der Presse ab-
montiert werden.
2.) Montieren
Nehmen Sie die SH7 sowie aus der Verpackung und schieben Sie
diese an den Pressenkopf. Dann montieren Sie wie gewohnt die
Schrauben und ziehen diese fest.
6.) Ablegen
Nach der Abmontage tellen Sie sicher, dass die Silikonmatte und der
Schutzüberzug richtig an der SH7 angebracht sind.
7.) Aufbewahrung
Überprüfen Sie nochmal bevor Sie die SH7 lagern ob die Silikonmat-
te auch wirklich die Membrane komplett abdeckt. Somit garantieren
Sie auch einen längeren Erhalt der SH7 und verhindern einen zu
schnelle Abnuntzung.
8.) Lagern
Nun können Sie die SH7 ablegen und für den nächsten Einsatz
bereithalten.
3.) Überzug entfernen
Wenn die SH7 richtig angebracht wurde, können Sie nun den Üner-
zug und die Silikonmatte abziehen.
4.) Anschließen und loslegen
Nun können Sie die Kabel mit der Presse verbinden und die Presse
in Betrieb nehmen. Bitte beachten Sie, dass die Transferpresse nicht
mehr als 190° C aufheizen dürfen. Bitte kleben Sie zur Sicherheit den
gelben Warnaufkleber noch auf ihren Controller. (Liegt bei)
1.) Unpacking
The Secabo SH7 is shipped with a silicone mat and a cover to
protect the membrane surface. Carefully remove them from the
box.
5.) After use
After you have used the SH7, please let it cool down completely.
Then you can put the silicone mat and the protective cover back
on. Now the plate can be removed from the press.
2.) Mount
Take the SH7 out of the packaging and slide it onto the press
head. Then mount the screws as usual and tighten them.
6.) Dismount
After dismantling, make sure that the silicone mat and the pro-
tective cover are properly attached to the SH7.
7.) Storage
Before storing the SH7, check again that the silicone mat really
covers the membrane completely. This will guarantee that the
SH7 will last longer and prevent it from wearing out too quickly.
8.) Store
Now you can store the SH7 and have it ready for the next use.
3.) Remove the cover
If the SH7 has been fi tted correctly, you can now remove the
cover and the silicone mat.
4.) Connect and start
Now you can connect the cables to the press and start using
the press. Please note that the heat of the heat press must not
exceed 190° C. To be on the safe side, please stick the yellow
warning sticker on your controller. (Enclosed)
ACHTUNG! Bitte bringen Sie den beigefügten Warnhinweis-Sticker an dem Controller Ihrer Transferpresse an!
ATTENTION! Please attach the enclosed warning sticker to the controller of your heat press!
Nicht mehr als
190° C aufheizen
Do not heat more
than to 190° C
SH7 Softheat
!!
Shelving table 16
Work table 16 (77cm x 77cm x 90cm) Art.Nr.: 182.030.00
Secabo Modulares Shelving System • Secabo Modular Shelving System
QUICK GUIDE
Hier sind ein paar wichtige Hinweise die sie beim Verwenden Ihrer SH7 Softheat beachten sollten:
Here are a few important tips to keep in mind when using your SH7 Softheat:
Hier haben wir das ganze Handling mit der SH7 vom Auspacken bis zur Aufbewahrung für Sie noch als Video visualisiert.
Falls Sie noch Fragen haben melden Sie sich jederzeit gerne per E-mail an [email protected]
Here we have visualised the entire handling of the SH7 from unpacking to storage for you as a video. If you have any ques-
tions, please do not hesitate to contact us by e-mail at [email protected].
QUICK GUIDE SH7 SOFTHEAT
WWW.SECABO.COM
1.) Auspacken
Die Secabo SH7 wird mit einer Silikonmatte und einem Überzug
versendet um die Membranfläche zu schützen. Nehmen Sie diese
vorsichtig aus dem Karton.
5.) Nach Benutzung
Nachdem Sie die SH7 benutzt haben, lassen Sie diese bitte vollstän-
dig abkühlen. Danach können Sie die Silikonmatte und den Schutz-
überzug wieder anbringen. Nun kann die Platte von der Presse ab-
montiert werden.
2.) Montieren
Nehmen Sie die SH7 sowie aus der Verpackung und schieben Sie
diese an den Pressenkopf. Dann montieren Sie wie gewohnt die
Schrauben und ziehen diese fest.
6.) Ablegen
Nach der Abmontage tellen Sie sicher, dass die Silikonmatte und der
Schutzüberzug richtig an der SH7 angebracht sind.
7.) Aufbewahrung
Überprüfen Sie nochmal bevor Sie die SH7 lagern ob die Silikonmat-
te auch wirklich die Membrane komplett abdeckt. Somit garantieren
Sie auch einen längeren Erhalt der SH7 und verhindern einen zu
schnelle Abnuntzung.
8.) Lagern
Nun können Sie die SH7 ablegen und für den nächsten Einsatz
bereithalten.
3.) Überzug entfernen
Wenn die SH7 richtig angebracht wurde, können Sie nun den Üner-
zug und die Silikonmatte abziehen.
4.) Anschließen und loslegen
Nun können Sie die Kabel mit der Presse verbinden und die Presse
in Betrieb nehmen. Bitte beachten Sie, dass die Transferpresse nicht
mehr als 190° C aufheizen dürfen. Bitte kleben Sie zur Sicherheit den
gelben Warnaufkleber noch auf ihren Controller. (Liegt bei)
1.) Unpacking
The Secabo SH7 is shipped with a silicone mat and a cover to
protect the membrane surface. Carefully remove them from the
box.
5.) After use
After you have used the SH7, please let it cool down completely.
Then you can put the silicone mat and the protective cover back
on. Now the plate can be removed from the press.
2.) Mount
Take the SH7 out of the packaging and slide it onto the press
head. Then mount the screws as usual and tighten them.
6.) Dismount
After dismantling, make sure that the silicone mat and the pro-
tective cover are properly attached to the SH7.
7.) Storage
Before storing the SH7, check again that the silicone mat really
covers the membrane completely. This will guarantee that the
SH7 will last longer and prevent it from wearing out too quickly.
8.) Store
Now you can store the SH7 and have it ready for the next use.
3.) Remove the cover
If the SH7 has been fi tted correctly, you can now remove the
cover and the silicone mat.
4.) Connect and start
Now you can connect the cables to the press and start using
the press. Please note that the heat of the heat press must not
exceed 190° C. To be on the safe side, please stick the yellow
warning sticker on your controller. (Enclosed)
ACHTUNG! Bitte bringen Sie den beigefügten Warnhinweis-Sticker an dem Controller Ihrer Transferpresse an!
ATTENTION! Please attach the enclosed warning sticker to the controller of your heat press!
Nicht mehr als
190° C aufheizen
Do not heat more
than to 190° C
SH7 Softheat
!!
Hier haben wir das ganze Handling vom Auspacken bis zum Aufbau für Sie noch als Video visualisiert.
Falls Sie noch Fragen haben, melden Sie sich jederzeit gerne per E-Mail an [email protected].
Here we have visualised the entire handling from unpacking to assembly for you as a video.
If you have any questions, please do not hesitate to contact us by e-mail at [email protected].

This manual suits for next models

1

Popular Storage manuals by other brands

ATTO Technology FastStream SC 5700 Specifications

ATTO Technology

ATTO Technology FastStream SC 5700 Specifications

Seagate STT320000A Online user's guide

Seagate

Seagate STT320000A Online user's guide

Ledger Nano S quick start guide

Ledger

Ledger Nano S quick start guide

Philips CD740RW Specifications

Philips

Philips CD740RW Specifications

Qsan Technology XN7008RE owner's manual

Qsan Technology

Qsan Technology XN7008RE owner's manual

Taylor-Wharton MicroBulk MB-450 Installation and operation manual

Taylor-Wharton

Taylor-Wharton MicroBulk MB-450 Installation and operation manual

HP storevirtual 3200 user guide

HP

HP storevirtual 3200 user guide

Westfalia 57 52 58 instruction manual

Westfalia

Westfalia 57 52 58 instruction manual

Gigabyte GC-RAMDISK user manual

Gigabyte

Gigabyte GC-RAMDISK user manual

Hitachi Travelstar 5K500.B install guide

Hitachi

Hitachi Travelstar 5K500.B install guide

Huawei OceanStor 5110 V5 Quick installation guide

Huawei

Huawei OceanStor 5110 V5 Quick installation guide

Sun Microsystems StorageTek L40 installation manual

Sun Microsystems

Sun Microsystems StorageTek L40 installation manual

Keter 120 US GAL Assembly instructions

Keter

Keter 120 US GAL Assembly instructions

Snap Appliance Snap Disk 10 quick start guide

Snap Appliance

Snap Appliance Snap Disk 10 quick start guide

FieldServer FS-8700-43 instruction manual

FieldServer

FieldServer FS-8700-43 instruction manual

Cavalry CAXB Series user manual

Cavalry

Cavalry CAXB Series user manual

Manhattan MSKL MS-3020 user guide

Manhattan

Manhattan MSKL MS-3020 user guide

Atmel DataFlash AT45DB321 Operation

Atmel

Atmel DataFlash AT45DB321 Operation

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.