SECO-LARM Enforcer EV-N6506-3W4Q User manual

EV-N6506-3W4Q
IP Covert PIR Camera
Web Admin User Manual
Features:
•H.265/MJPEG, Dual Stream IP Camera
•1/2.8" 5MP Sony CMOS
•D-WDR (Digital Wide Dynamic Range)
•3.7mm Covert pinhole lens
•
True Day & Night function with ICR module
•
12VDC operation, 802.3af PoE
•ONVIF Profile S
•1440p Resolution
•
2DNR (2D Digital Noise Reduction)
•3DNR (3D Digital Noise Reduction)
•Camera is hidden in a non-functioning PIR
sensor housing

ENFORCER IP Camera Web Admin User Manual
2SECO-LARM U.S.A., Inc.
Programmable Features................................... 2
Accessing the IP Camera Interface
.................. 3
IP Camera Interface
......................................... 3
Image Settings
................................................. 4
Playback Settings
............................................. 4
Log
................................................................... 4
Device Configuration
........................................ 5
Setting
-Record-Record..................................... 5
Setting
-Record-Snapshot................................. 5
Setting
-Alarm.................................................... 5
Setting
-Alarm-Intelligent Alert........................... 6
Setting
-Alarm-Video Blind ................................ 6
Setting
-Alarm-Video Loss................................. 7
Setting
-Alarm-Alarm Input................................ 7
Setting
-Alarm-Alarm Output ............................. 8
Setting
-Alarm-Abnormal................................... 8
Setting
-System................................................. 8
Setting
-System-General................................... 9
Setting
-System-Encode.................................... 9
Setting
-System-Network................................. 10
Setting
-System-NetService ............................ 10
Setting
-System-GUI Display........................... 11
Table of Contents:
•Exposure
Adjust the shutter speed, automatic gain control
(AGC), and defog settings
•
Digital Wide Dynamic Range (D-WDR)
Provide clear images even under circumstances
where backlight illumination can vary
•
Back Light Compensation (BLC)
Adjust the exposure to properly display the
subject in front of bright light sources
•
White Balance
Adjust the color temperature/image color
•
Day & Night
Adjust the level of ambient light that triggers the
camera to switch between color and B/W modes
•
Digital Noise Reduction (DNR)
Adjust for less interference on the screen in an
area with low illumination
Programmable Features:
Setting-System-RS232 ...................................11
Setting-System-Camera param. ...............11~12
Setting-Advanced ...........................................12
Setting-Advanced-HDD Manage ....................13
Setting-Advanced-Account .............................13
Setting-Advanced-AutoMaintain .....................13
Setting-Advanced-Default...............................14
Setting-Advanced-Import Export.....................14
Setting-Advanced-Upgrade ............................14
Setting-Info .....................................................15
Setting-Info-HDD Info .....................................15
Setting-Info-Log ..............................................15
Config Manager ..............................................16
Config Manager-Alarm Setting- Normal..........16
Config Manager-Alarm Setting-AlarmLink ......16
Config Manager-System Setting.....................16
Config Manager-About....................................17
Troubleshooting..............................................17
Warranty .........................................................17
NOTE:All screen images in this manual are simulated.
D-WDR OFF
D-WDR ON
BLC OFF
BLC ON
DNR OFF
DNR ON

ENFORCER IP Camera Web Admin User Manual
SECO-LARM U.S.A., Inc. 3
Accessing the IP Camera Interface:
IP Camera Interface:
Login Screen
1. To access the IP Camera interface, input the IP address of the front-
end device into the URL address bar
of the Internet Explorer browser (default IP address: 192.168.1.10).
2. ActiveX installation is required when the IP camera interface is first accessed. Follow the prompts to
install ActiveX.
3. In the following login screen, input the default User Name (Default: admin) and Password
(Default: Leave
Blank).
4. Click "Login" to proceed.
Once within the IP Camera interface, the following tabs are made available:
-Playback: The Playback tab provides the primary live camera feed and limited settings for adjusting the
camera's position and image.
-Log: The Log tab allows for full replay and review of recorded video.
-DeviceCfg:The DeviceCfg tab allows for full configuration of the IP camera's settings.
-LocalCfg:The LocalCfg tab allows for search and review of programmed alarms.
-Log Out: Press the Log out tab to log out completely of the IP camera interface.

ENFORCER IP Camera Web Admin User Manual
4SECO-LARM U.S.A., Inc.
Image Settings:
The playback settings allows for full replay and review of recorded
video.
1. PlayBack – Choose between Remote or Local playback
2. Query Mode – Select to search for video by Name or by
specific Time
3. Type – Select the type of video or picture to search for
4. Begin – Select the beginning video recording time to search
5. End – Select the ending video recording time to search
6. Click Search to find video
To open the Image Settings panel, click the "Images" button. The
Image Settings panel allows for adjustment of the video image's
brightness, contrast, hue, and saturation.
-Brightness: Adjust the brightness of the video image
-Contrast: Adjust the contrast of the video image
-Saturation: Adjust the saturation of the video image
-Tone: Adjust the tone of the video image
Playback Settings:
Log:
Alarm Log:
The alarm log
records the camera’s alarm features.
Displaying the alarm type, date, time, device, and
channel.
Operate Log:
The Operate log records the camera’s login attempts.

ENFORCER IP Camera Web Admin User Manual
SECO-LARM U.S.A., Inc. 5
Device Configuration:
Setting –Record – Record:
1.
Channel – Select channel to use (default = 1)
2.
Length – Select the max length of recorded video
(default is 60 minutes)
3.
PreRecord – Set the pre-record time
4.
Record Mode:
a. Timing – Automatically records based on
up to 4 timing configurations.
b. Manual – Manually set the camera to
record or stop recording
c. Stop – Stops the camera from recording
5.
Click OK to save.
The Device Configuration provides access to the
Record and Record Snapsho
t settings
1. Channel – Select channel to use (default = 1)
2.
PreSnap – Select number of PreSnaps (default = 1)
3.
Record Mode:
a. Timing – Automatically records based on
up to 4 timing configurations.
b. Manual – Manually set the camera to
snap a snapshot
c. Stop – Stops the camera from recording
4.
Click OK to save
Setting –Alarm:
1.
Intelligent Alert – Configure alerts
2.
Video Blind – Configure settings pertaining to
camera being blinded (spray painted or covered)
3.
Video Loss – Configure settings for loss of video
4.
Alarm Input – Configure alarm inputs
5.
Alarm Output – Configure alarm outputs
6.
Abnormal – Configure settings for abnormalities
(IP conflicts, not enough storage)
Setting –Record – Snapshot
:

ENFORCER IP Camera Web Admin User Manual
6SECO-LARM U.S.A., Inc.
Setting – Alarm – Intelligent Alert:
Setting – Alarm – Video Blind:
1. Channel – Select channel to use (default = 1)
2.
Enable – Check to enable
3.
Human Detect – Check to detect humans only
4.
Recognition – Select the sensitivity from Lowest to
Highest (default = middle)
5.
Region – Select the region to monitor
6.
Period – Set the schedule to monitor
7.
Intervals – Set the desired intervals in seconds
(default = 2 seconds)
8.
Alarm Output – Default = 1
9.
Delay – Set the desired delay in seconds (default=10 seconds)
10.
Record Channel – Default = 1
11.
Snapshot Channel – Default = 1
12.
PTZ Activation – Not supported
13.
Send Email – Check to alert using email
14.
FTP – Check to alert to FTP server
15.
App Push – Check to force open application
16.
Write log – Check to write to the log file
17.
AlarmSound – Check to enable sound
18.
SoundPlayType – Select from pre-recorded messages
19. Click OK to save
1. Channel – Select channel to use (default = 1)
2.
Enable – Check to enable
3.
Recognition – Select the sensitivity from Lowest to
Highest (default = middle)
4.
Period – Set the schedule to monitor
5.
Alarm Output – Default = 1
6.
Delay – Set the desired delay in seconds (default =
10 seconds)
7.
Record Channel – Default = 1
8.
Snapshot Channel – Default = 1
9.
PTZ Activation – Not supported
10.
Send Email – Check to alert using email
11.
FTP – Check to alert to FTP server
12.
App Push – Check to force open application
13.
Write log – Check to write to the log file
14.
Click OK to save

ENFORCER IP Camera Web Admin User Manual
SECO-LARM U.S.A., Inc. 7
Setting –Alarm – Video loss:
Setting – Alarm – Alarm Input:
1. Channel – Select channel to use (default = 1)
2. Enable – Check to enable
3. Period – Set the schedule to monitor
4. Alarm Output – Default = 1
5. Delay – Set the desired delay in seconds
(default = 10 seconds)
6. Record Channel – Default = 1
7. Snapshot Channel – Default = 1
8. PTZ Activation – Not supported
9. Send Email – Check to alert using email
10. FTP – Check to alert to FTP server
11. App Push – Check to force open application
12. Write log – Check to write to the log file
13. Click OK to save
1. Channel – Select channel to use (default = 1)
2. Enable – Check to enable
3. Type – Select Normally Open or Normally
Close Input
4. Period – Set the schedule to monitor
5. Interval – Set the desired interval in seconds
(default = 2 seconds)
6. Alarm Output – Default = 1
7. Delay – Set the desired delay in seconds
(default = 10 seconds)
8. Record Channel – Default = 1
9. Snapshot Channel – Default =1
10. PTZ Activation – Not supported
11. Send Email – Check to alert using email
12. FTP – Check to alert to FTP server
13. App Push – Check to force open application
14. Write log – Check to write to the log file
15. Click OK to save

ENFORCER IP Camera Web Admin User Manual
8SECO-LARM U.S.A., Inc.
Setting: Alarm – Alarm Output:
Setting: Alarm – Abnormal:
Setting – System:
1. Channel – Select channel to use (default = 1)
2. Enable – Check to enable
3. Configuration – Select to automatically output
alarm
4. Manual – Select to manually output alarm
5. Stop – Select to have no alarm output
6. Status – Check to visually show alarm output
7. Click OK to Save
1. Event Type:
a. Storage Device Not Exist – Will alert
when storage device is not connected
b. Storage Space Lack Alarm – Will alert
when storage is running low
c. Storage Device Access Failure – Will
alert when cannot access device
d. IP Conflict – Will alert when another
device has the same IP as camera
e. NetAbort – Will alert when camera is
disconnected from the network
2. Enable – Check to enable
3. App Push – Check to force open application
4. Click OK to save
1. General – General configurations
2. Encode – Encoding configurations
3. Network – Network configurations
4. NetService – Services available
5. GUI Display – OSD configurations
6. PTZ Config – PTZ configurations
7. RS232 – Serial port configurations
8. Camera param. – Advanced camera
configurations
9. Setting – System – General
10. Click OK to save

ENFORCER IP Camera Web Admin User Manual
SECO-LARM U.S.A., Inc. 9
Setting –System – General:
Setting – System – Encode:
1. Time Zone – Select time zone
2. System Time – Enter date and time
3. Date Format – Select the format to display the date
4. DST – Check for Daylight Savings Time
5. Date Separator – Select character to use to separate the
date
6. Time Format – Select between 12 hour or 24 hour clock
7. Language – Select language
8. HDD Full – Select to either overwrite or stop recording
when hard drive is full
9. DVR No – Set the number for the DVR (default = 0)
10. Video Standard – Select between PAL or NTSC
11. Auto Logout – Set a time limit in minutes to
automatically log off
12. Click OK to save
1. Channel – Select channel to use (default = 1)
2. Compression – Select between H.265 or H.265X
3. Resolution – Select between 2MP, 4MP, or 5MP
4. FPS – Select the frames per second
5. Bit Rate Type – Select between VBR or CBR
6. Quality – Select between Worst and Best (default is
Best)
7. Bit Rate (Kb/S) – Set the Bit rate
8. I Frame Interval – Set the I frame interval (default = 2)
9. Video/Audio – Check to record video or audio
10. Static Configuration – Select profile between Baseline,
Main Profile, and High profile. High profile takes up more
space for the stream but the picture quality is better.
11. Smart Encoding – Select to use smart encoding on
H.265+

ENFORCER IP Camera Web Admin User Manual
10 SECO-LARM U.S.A., Inc.
Setting –System – Network:
Setting –System – NetService:
1. Net Card – Select network adapter
2. IP Address – Enter IP Address for camera
3. Subnet Mask – Enter subnet mask
4. Gateway – Enter default gateway
5. Primary DNS – Enter primary DNS server address
6. Secondary DNS – Enter secondary DNS server address
7. Media Port – Enter TCP steaming port (default = 34567)
8. HTTP Port – Enter HTTP port (default = 80)
9. Onvif Port – Enter Onvif port (default = 8899)
10. Device Info – Displays camera mac address
Transfer Policy:
a. Adaptive – For lower bandwidth network. Preview screen automatically adjust to substream.
b. Quality Preferred – For higher bandwidth network. Preview screen stays in main stream.
c. Fluency Preferred – Changes the encoder settings and lowers the stream without reducing
frame rate to ensure a smoother video.
d. Network Priority – Limits the users that can view the camera simultaneously. Users with higher
bandwidth will take priority.
11. Click OK to save
NetService displays the network services available.
Double-click each option listed below to configure:
1. IP Filter – Blacklist and White list services
2. EMAIL – Use email to send alerts or other services
3. NTP – Set the time server
4. UPNP – Allows devices in your network to discover
each other
5. FTP – Configure the file server
6. AlarmServer – Configure an alarm server
7. RTSP – Real Time Streaming Protocol – used to
stream camera video over network
8. Cloud – Set up a third party cloud provider
9. App Push – Force open an application
10. Serial Pass-Through – Configure RS232 settings