SECO-LARM SLI Enforcer EV-N4506-2S4Q User manual

®
EV-N4506-2S4Q
IP Corner-Mount Camera
Manual
Features:
1/2.8" 5MP Sony STARVIS™ CMOS
H.265, H.264/MJPEG, Tri-stream IP
Camera
Max. 30FPS/Full HD 5MP (2592x1944)
Remote access via web browser
Network Bandwidth Control
Event Alarm, E-mail, FTP Function
ONVIF Profile S
30 Covert IR LEDs for discreet monitoring
in the dark
True Day & Night function with
ICR mechanism
Vandal-resistant metal front panel
3DNR & WDR
12VDC, PoE (IEEE802.3af)

ENFORCER IP Corner-Mount Camera
2 SECO-LARM U.S.A., Inc.
Overview:
Specifications:
Parts List:
Type Corner-Mount Camera
Sensor
1
/
2.8
"
5
MP Sony
STARVIS
™
CMOS
Video encoding
H.265,
H.264, MJPEG
Resolution
5MP (2592x1944)
DNR
2DNR
Yes
3DNR
Yes
WDR
Yes
# of IR LEDs
30 (940nm)
Lens
2.8
mm
Viewing angle
1
26
°
Minimum
illumination
IR On
0 Lux
IR Off
0.01 Lux
F Stop
1.6
Gamma
correction
0.45
S/N ratio
5
0dB
Gain control
Auto
White balance
Auto
Operating voltage
12VDC, PoE
(
IEEE802.3af
)
Current draw (IR Off)
140
mA
max.
IP Rating
IP65
Operating temperature
14°~122° F (
-
10°~50° C)
Dimensions
7
1
/
2
"
x5
1
/
2
"
x1
11
/
16
"
(190x140x43 mm)
Weight
13.75
-
oz (390g)
1x
Camera
1x
Camera cover
1x
CD
4x
Mounting screws
1x
Pigtail connector
3x
Security screws
1x
Security wrench
1x
Manual
71/2" (190mm)
5
1
/
2
"
(140mm)
1
11
/
16
"
(43mm)

ENFORCER IP Corner-Mount Camera
SECO-LARM U.S.A., Inc. 3
Installation:
Overview:
Before Starting:
*IMPORTANT: Do not cut DC jack or RJ45 jack as warranty will be voided.
Mounting screws
Security screws
Camera cover
DC jack DC plug
RJ45 jack
1.
Please read this manual carefully and keep it for
future reference.
2. Use the camera within given temperature and
electrical limits.
3. Do not point the camera at the sun. Heat could
damage the camera, even when not in use.
4.
Do not mount the camera in areas exposed to
radiation, strong magnetic fields, or strong
electrical signals.
5. Do not open or disassemble the camera. There
are no field-serviceable parts inside.
6. Do not drop the camera or subject it to strong
vibrations.
1.
Use the included security wrench to loosen the
screws and remove the camera cover from the
camera.
2. Run a 12VDC power supply wire and cable with
an RJ45 jack through the wall at the corner
where the camera is to be mounted.
3. Execute "IP Manager" on the PC.
4.
Press the "Find" button. IP cameras connected to
the same router will be searched and listed. This
may take several seconds. Default IP address is
192.168.1.30.
5. Right-click the desired product, and press "IP
Change".
6. Use web port number 80. This is an internal port.
7.
IP address: You may use Dynamic IP or you may
set Static IP as below:
8. Typical IP setting is as follows.
9. IP address.: 192.168.1.10 (you can change the
last column)
Netmask: 255.255.255.0
Gateway: 192.168.1.1
DNS1/2: You can copy the PC's network
properties.
This is for internet environments.
10. Input "admin" for User ID and password
NOTE: It is recommended that you change the
default password.
11. Press "Change" to save settings and allow 10s
for changes to appear.
12. Right-click the desired device and click "Open
Web Page".
13. Enter Username / Password.
14. Click "Live" on top right of the screen.
15. Click yes for "ActiveX Control".
16. After the installation of Active X, you will be able
to view the live feed only with Internet Explorer.
Visit http://www.seco-larm.com/EV-N4506-2S4Q
for the Web Admin Manual.

ENFORCER IP Corner-Mount Camera
4 SECO-LARM U.S.A., Inc.
The screen in blank
 Check that the camera is powered up.
 Check that the power supply’s polarity is correct.
 Check that the monitor is powered up.
 Check that the video cable connecting the camera to the
monitor is connected properly.
The screen image is dim  Clean the lens using a soft, clean cloth.
 Check that the light source is adequate.
The screen image has poor contrast.  Adjust the monitor’s contrast knob.
 Change the position of the camera.
The screen image flickers.  Change the position of the camera.
The screen image is distorted.  Change the position of the camera.
The camera case is hot.  Check that the correct power supply is in use
IR LEDs do not turn on.  Check that the correct power supply is in use
Troubleshooting:
SECO-LARM
® U.S.A., Inc.
16842 Millikan Avenue,
Irvine, CA 92606
Website:
www.seco
-
larm.com
Phone: [phone] | [phone] Email: [e-mail]
PIKSR1
MI_EV-N4506-2S4Q_210430.docx
NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-
LARM reserves
the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All t
rademarks are the
property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2021 SECO-LARM U.S.A.,
Inc. All rights
reserved.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while
used in normal
service for three (3) years from the date of sale to the original customer. SECO-
LARM’s obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if
damage is caused by or attributed to acts o
f God, physical or electrical misuse or abuse, neglect, repair or alteration, improper
or abnormal usage, or faulty installation, or if for any other reason SECO-
LARM determines that such equipment is not
operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO-
LARM
and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s option.
In no event
shall SECO-LARM be liable for any special, collateral, incid
ental, or consequential personal or property damage of any kind
to the purchaser or anyone else.
IMPORTANT:
Users and installers of this product are responsible for ensuring this product complies with all national, state,
and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM
will not be held
responsible for the use of this product in violation of any current laws or statutes.
FCC COMPLIANCE STATEMENT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2)
THIS DEVICE MUST ACCEPT
ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Notice: The changes or modifications not expressly approved by the party responsible for compliance could void
the user’s
authority to operate the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device
is permitted. Any change to the antenna or the device could result in the device exceeding th
e RF exposure requirements
and void user’s authority to operate the device.
California Proposition 65 Warning: These
products may contain chemicals which are known to the State of California to
cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.