Seconique Corona User manual

CORONA 2 DRAWER CONSOLE TABLE
ASSEMBLY INSTRUCTIONS
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
CARE AND MAINTENANCE
After unpacking this product please keep the original packaging in case it needs to be
returned for any reason.
• Please ensure all fittings and parts are present before commencing with assembly.
• We recommend that you lay a blanket or sheet on the floor to avoid damage to both your
floor and the product.
• We strongly recommend that you keep children away from your work area.
• Assemble this product as close to its final position as possible.
• Never drag or push products as this could cause damage to the joints making it inferior.
• Do not place this product next to a radiator or in direct sunlight.
• Wood is a natural product and may expand if subjected to damp and may shrink or crack
if subjected to heat. Therefore it is recommended that room temperature is maintained,
with no sudden temperature fluctuations.
• Make sure any spillage is wiped off immediately.
• Do not place hot or chilled items directly on to the surface, use a place mat or marking
will occur.
• For general cleaning use a duster, and do not use detergents of any kind. However, the
surface will need to be retreated from time to time. This can be done by using block wax
(unperfumed) and rubbing it over the whole item.
• From time to time it may be necessary to tighten fittings, regular inspections should be
carried out.
FOR DOMESTIC USE ONLY
SEC/SH/11/22/MY1
Page 01
WITH SHELF

* Please check contents and read the instructions before commencing assembly.
* Assemble this product following the enclosed instructions carefully.
* Please take care to avoid damaging panels during assembly.
* Use of power tools to assemble this product will invalidate
any claim and damage this product making it unsafe !!!
* Please assemble on a clean soft surface to avoid damage.
Part Code
Part Number Part Description Quantity Carton
01
02
03
04
05
06
07
08
09
10
11
S300-304-003-MY1-01 Top Panel 11/1
Side Panel
Back Panel
Front Frame
Right Leg
Drawer Runner
Le Leg
Drawer Base
Drawer Side
Drawer Back
S300-304-003-MY1-02
S300-304-003-MY1-03
S300-304-003-MY1-04
S300-304-003-MY1-05
S300-304-003-MY1-06
S300-304-003-MY1-07
S300-304-003-MY1-08
S300-304-003-MY1-09
S300-304-003-MY1-10
S300-304-003-MY1-11
2
1
1
2
2
2
2
4
2
2
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
Drawer Front
PARTS LIST
SEC/SH/11/22/MY1
Page 02
12
13
14
Shelf
Hardware Kit
S300-304-003-MY1-12
S300-304-003-MY1-13
S300-304-003-MY1-14
1
1
1
1/1
1/1
1/1
Centre Drawer Runner
01
07
02
02
03
06 13 06
07
05
05
14
12
04
11
09
09
10
11
09
09
10

8 x 30mm
D28
3,5 x 35mm
6 x 30mm
FITTINGS
TOOLS REQUIRED
Page 03
FITTINGS
SEC/SH/11/22/MY1
C
B
A
02
16
26
2x
1x
1x
G
F
E
01
12
02
Black

Page 04
SEC/SH/11/22/MY1
02- x2
SIDE PANEL
STEP 2
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
D24
STEP 1
06 - x2
DRAWER RUNNER
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
F12
13 - x1
CENTRE DRAWER RUNNER
Please assemble on
a clean soft surface
to avoid damage.
Please assemble on
a clean soft surface
to avoid damage.
Ø 8 x 30mm
03- x1
BACK PANEL
04- x1
FRONT FRAME
Ø 8 x 30mm
D
F
13
06
06
FF
FF
FF
FF
FF
FF
D
D
D
D02
D
D
D
D
12
D
D
02
04
03
D
D
D
D
D
D
D
D
D
D
D
D
D
D
12- x1
SHELF

Please assemble on
a clean soft surface
to avoid damage.
Page 05
SEC/SH/11/22/MY1
02 - x2
SIDE PANEL
STEP 4
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
STEP 3
03- x1
BACK PANEL
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
A02
04- x1
FRONT FRAME
06- x2
DRAWER RUNNER
05 - x1
RIGHT LEG
07- x1
LEFT LEG
Ø 3,5 x 35mm
A08
Please assemble on
a clean soft surface
to avoid damage.
Please Note:
The cut out on parts 06 & 13
should face inwards.
06
13
03
04
06
05
07
02
13- x1
CENTRE DRAWER RUNNER
A
AA
A

Ø 3,5 x 35mm
A06
Page 06
SEC/SH/11/22/MY1
STEP 6
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
STEP 5
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
Please assemble on
a clean soft surface
to avoid damage.
Please assemble on
a clean soft surface
to avoid damage.
Ø 3,5 x 35mm
A06
A
AA
A
A
A
12- x1
SHELF
12
A
A
A
A
A
A

Page 07
SEC/SH/11/22/MY1
STEP 8
STEP 7
01- x1
TOP PANEL
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
A04
Please assemble on
a clean soft surface
to avoid damage.
Ø 3,5 x 30mm
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
B16
8- x2
DRAWER BASE
9- x4
DRAWER SIDE
Please assemble on
a clean soft surface
to avoid damage.
1
Ø 3,5 x 35mm
A
A
A
A
10- x2
DRAWER FRONT
11- x2
DRAWER BACK
C02
E02
B
B
B
B
B
BB
B
C
E
x2
11
10
8
9
9

Page 08
SEC/SH/11/22/MY1
STEP 10
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
STEP 9
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
Please assemble on
a clean soft surface
to avoid damage.
G01
Wall
Top
Top
Wall Top
D04
Ø 8 x 30mm
2x
1x
1x
Serious or fatal injuries can occur from furniture tipping
recommend that it is permanently fixed to the wall.
Wall fixings are not supplied with this product as different wall
materials require different types of fixing devices.
Please make sure you use fixings suitable for the walls in your home.