Seconique Panama Console Table User manual

Page 01
PANAMA CONSOLE TABLE
ASSEMBLY INSTRUCTIONS
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
CARE AND MAINTENANCE
After unpacking this product please keep the original packaging in case it needs to be
returned for any reason.
• Please ensure all fittings and parts are present before commencing with assembly.
• We recommend that you lay a blanket or sheet on the floor to avoid damage to both your
floor and the product.
• We strongly recommend that you keep children away from your work area.
• Assemble this product as close to its final position as possible.
• Never drag or push products as this could cause damage to the joints making it inferior.
• Do not place this product next to a radiator or in direct sunlight.
• Wood is a natural product and may expand if subjected to damp and may shrink or crack
if subjected to heat. Therefore it is recommended that room temperature is maintained,
with no sudden temperature fluctuations.
• Make sure any spillage is wiped off immediately.
• Do not place hot or chilled items directly on to the surface, use a place mat or marking
will occur.
• For general cleaning use a duster, and do not use detergents of any kind. However, the
surface will need to be retreated from time to time. This can be done by using block wax
(unperfumed) and rubbing it over the whole item.
• From time to time it may be necessary to tighten fittings, regular inspections should be
carried out.
SEC/SW/02/21/PJ1
FOR DOMESTIC USE ONLY

* Please check contents and read the instructions before commencing assembly.
* Assemble this product following the enclosed instructions carefully.
* Please take care to avoid damaging panels during assembly.
* Use of power tools to assemble this product will invalidate
any claim and damage this product making it unsafe !!!
* Please assemble on a clean soft surface to avoid damage.
5
4
5
4
5
3
5
4
5
4
5
1
5
25
6
5
7
5
6
5
3
5
95
8
5
10
5
11 5
9
Part Code
Part Number Part Description Quantity Carton
1
2
3
4
5
6
7
8
9
10
11
S300-304-006-PJ1-01 Front Frame 11/1
Back Panel
Side Panel
Leg
Top Panel
Side Drawer Runner
Centre Drawer Runner
Drawer Front
Drawer Side
Drawer Boom
Drawer Back
S300-304-006-PJ1-02
S300-304-006-PJ1-03
S300-304-006-PJ1-04
S300-304-006-PJ1-05
S300-304-006-PJ1-06
S300-304-006-PJ1-07
S300-304-006-PJ1-08
S300-304-006-PJ1-09
S300-304-006-PJ1-10
S300-304-006-PJ1-11
1
2
4
1
2
1
2
4
2
2
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
5
95
8
5
10
5
11 5
9
5
5
SEC/SW/02/21/PJ1
Page 02

FITTINGS
TOOLS REQUIRED
Page 03
FITTINGS
SEC/SW/02/21/PJ1
2x
1x
1x
F01

Page 04
SEC/SW/02/21/PJ1
3 - x2
SIDE PANEL
STEP 2
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
A20
STEP 1
1 - x1
FRONT FRAME
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
A14
2 - x1
BACK PANEL
Please assemble on
a clean soft surface
to avoid damage.
Please assemble on
a clean soft surface
to avoid damage.
A
Ø 8 x 30mm
6 - x2
SIDE DRAWER RUNNER
7 - x1
CENTRE DRAWER RUNNER
Ø 8 x 30mm
A
AA
A
A
A
A
A
A
A
A
A
A
AA
A
A
AA
A
A
AA
AA
A
A
2x
2x
2
2
2
1
2
3
5
7
5
6

Page 05
SEC/SW/02/21/PJ1
1 - x1
FRONT FRAME
STEP 4
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
B06
STEP 3
3 - x2
SIDE PANEL
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
B08
4 - x4
LEG
Ø 3,5 x 30mm
2 - x1
BACK PANEL
Ø 3,5 x 30mm
6 - x2
SIDE DRAWER RUNNER
Please assemble on
a clean soft surface
to avoid damage.
4
4
4
4
4
3
BBB
BB
B
2x
1
6
6
6
2
7
7
6
6
B
B
B
BB
B
7 - x1
CENTRE DRAWER RUNNER
B
Please note the position
of the dowel holes
when attaching part 6
Please note the position
of the dowel holes
when attaching part 6

Page 06
SEC/SH/01/21/PJ1
5 - x1
TOP PANEL
STEP 6
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
B06
STEP 5
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
B08
Ø 3,5 x 30mm
Ø 3,5 x 30mm
B
B
B
B
BB
B
Please assemble on
a clean soft surface
to avoid damage.
2x
B
B
B
B
A
A
A
A
B
6
5
B
B
A04
Ø 8 x 30mm
Please assemble on
a clean soft surface
to avoid damage.

Page 07
STEP 10
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
STEP 9
8 - x2
DRAWER FRONT
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
C16
C
C
C
C
C
C
C
11
5
9
5
9
10
D
E
Please assemble on
a clean soft surface
to avoid damage.
2x
9 - x4
DRAWER SIDE
10 - x2
DRAWER BOTTOM
11 - x2
DRAWER BACK
2x
2x
SEC/SW/02/21/PJ1
AA
AA
A04
Ø 8 x 30mm
A
8
D02
E20

Page 08
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
L01
STEP 11
Serious or fatal injuries can occur from furniture tipping
recommend that it is permanently fixed to the wall.
Wall fixings are not supplied with this product as different wall
materials require different types of fixing devices.
Please make sure you use fixings suitable for the walls in your home.
Wall
Top
Top
Wall Top
2x
1x
1x
SEC/SW/02/21/PJ1