Secur ID-11 User manual

Secure Vision, Secure Safety Installation Manual:
ID-11 Controller
www.secursignal.com
IMPORTANT!
This manual provides all the necessary information for your SECUR product to be properly and safely
installed. Please read all instructions before installation, and make sure you follow them carefully during
the installation process. Failure to follow these instructions may result in DAMAGE to the product or
vehicle, and/or SERIOUS INJURY to you and your passengers!
NOTE: Do not install and/or operate this product unless you have read and understand all the safety information and instructions contained in this
manual.
Functions and Programming
Default: All buttons are default as NO/OFF Button
Programmable
Key: C1-C11
Momentary Switch Programming
Direcon
Push C1 and C11 together for 5 seconds to enter Momentary Switch programming mode. L1 and R1 will
be steady on to indicate you are in programming mode for momentary switch.
-Hold the buon you desire to program for 3 Seconds to set as Momentary Switch. | The Red LED will
ash 3 mes to indicate it has been set as momentary boom.
-Hold for another 3 seconds to reverse the seng. | The Red LED will ash once to indicate it has
been set as ON/OFF switch.
-Push C1 and C11 together for 5 seconds to exit programming mode.
Programmable
Key: C1-C11
Direcon
Push C1 and C10 for 5 seconds to enter Express Key Programming Mode for C11. L3 and R3 will be
steady on to indicate you are now in programming mode for C11 express key.
-C11 Express key is design to quickly acvate a set of funconality together at once.
-Once enter Express Key Programming Mode, press on the buons that you wish to acvate together.
| The Red LED will light up to indicate the buon has been selected.
-Push C1 and C10 again for 5 seconds to exit the programming mode.

Express Key Programming
L1-5 / R1-5:
Flash Paern Indicator
C1-C11:
Programmable buons
C1:
Default set as an ON/OFF switch.
You may also hold the buon for
5 seconds to disable all funcons.
|Hold the buon for 5 seconds to
resume all previous 
Wiring:
-Each wire is design to connect to
one auxiliary funcon
-Input amps shall remain below
0.2Amps
-Please see the diagram on the
lefor wiring diagram for each
buon

Manufacturer Limited Warranty Policy: Manufacturer warrants that on the date of purchase this product. This Limited
Warranty extends for Thirty Six (36) months from the date of purchase.
DAMAGE TO PARTS OR PRODUCTS RESULTING FROM TAMPERING, ACCIDENT, ABUSE, MISUSE, NEGLIGENCE,
UNAPPROVED MODIFICATIONS, FIRE OR OTHER HAZARD; IMPROPER INSTALLATION OR OPERATION; OR NOT BEING
MAINTAINED IN ACCORDANCE WITH THE MAINTENANCE PROCEDURES SET FORTH IN MANUFACTURER’S INSTALLATION
AND OPERATING INSTRUCTIONS VOIDS THIS LIMITED WARRANTY.
Programmable
Key: C10
Interlock Funcon Programming
Push C1 and C9 together for 5 seconds to enter interlock programming mode for C9-C10. L4 and R4
will be steady on to indicate you are now in programming mode for C9 and C10.
-Hold C10 for 5 second to acvate interlock funcon. Now C10 will be disabled when C9 is acvated.
|The C10 Red LED will ash 3 mes to indicate it has been se
-Push C1 and C9 for 5 seconds to exit interlock programming mode.
Direcon
R1
R2
R3
R4
R5
Press C5 and C8 together for 5 seconds to exit programming mode for C5-C8
Press C5 and C8 together for 5 seconds to enter warning/arrow light display programming mode for
C5-C8. L2 and R2 will be steady on to indicate you are now in programming mode for C5-C8.
-By pressing the buon, the LED R1 to R5 will indicate which light indicator funcon has been
selected
Programmable
Keys: C5-C8
The LED indicator funcon has been disabled
The LED indicator is set to display Arrow Right to Le
Direcon
Warning / Trac light ash paern indicator: this funcon is only available with our TRIDENT lightbar
The LED indicator is set to display Warning Light All Flash
The LED indicator is set to display Middle to Outward
The LED indicator is set to display Arrow Leto Right
Press C1 and C8 together for 10 second to reverse the device back to default
Reset to Default
Secure Vision, Secure Safety Installation Manual:
ID-11 Controller
www.secursignal.com
Installation
Attach and secure the controller onto the panel stand. Place the device onto a clean desired surface,
where it can be easily accessible to the user. Use the attached adhesive pad* to secure the device onto the
surface. Should you wish to remove / re-locate the controller, you may use alcohol or similar cleaning
formula to remove the left-over adhesive residue.
* The supplied adhesive pad is designed for one time use. You may replace it with other double side
adhesive tapes.