Security Brands 14-REC300 User manual
ON
12345678910
13
2
4
Coaxial Connector
INSTRUCTIONS RECEIVER 300 Model 14-REC300
1 of 2
IN THE BOX
Make sure you have everything
shown here.
AntennaReceiver 300 1.5-foot Coaxial Cable
DIP Switches on Receiver 300
(default positions)
Receiver 300
(cover removed)
Receiver 300
(cover in place)
WHAT’S WHAT
1. DIP switches
2. RF status LED
3. Power and relay terminals
4. Coaxial antenna connector
SETUP
1. Remove screws from Receiver 300 unit cover and
remove cover to reveal DIP switches.
CAUTION! Be gentle with coaxial connection
when removing cover. Do not let cover hang
free; doing so may damage unit!
2. Set DIP switches to desired positions.
NOTE: For best results, we recommend using
the Security Brands Remote 300 (14-R300).
NOTE: By default, the DIP switches are matched
to the default DIP switch positions on the
Remote 300 and other 300-MHz remotes.
For security reasons, we recommend using
custom DIP switch positions.
NOTE: Some DIP switches may be labeled
dierently. The position labeled 10 corresponds
to the position labeled 0, and some DIP switches
have the o position labeled as OPEN.
call
(972) 474-6390
or email
NEED
HELP
Two-Year Limited Warranty
Visit securitybrandsinc.com/warranty/ for details
12–24 VAC/DC
POWER
RELAY
12–24 VAC/DC
POWER
POS. (+)
NEG. (–)
COM
REVERSE LOOP
COM
OPEN
STOP
CLOSE
12–24-VAC/DC
Power Source
(Not Included)
NEG. (–)
COM
NO
FREE EXIT
COM
COM
RADIO
+–
NC
POS. (+)
Receiver 300
Gate / Door Operator
INSTRUCTIONS
2 of 2
RECEIVER 300 Model 14-REC300
© 2021 Security Brands, Inc. All rights reserved. I-14REC300-EN Rev. B (12/2021)
WARNING! AUTOMATIC GATES CAN CAUSE
SERIOUS INJURY OR DEATH!
ALWAYS CHECK THAT THE GATE PATH IS
CLEAR BEFORE OPERATING!
REVERSING OR OTHER SAFETY DEVICES
SHOULD ALWAYS BE USED!
WIRING AND INSTALLATION
1. Connect power and relay wires to screw terminals
on Receiver 300 unit, and connect other ends to
gate or door operator as instructed by gate or
door operator manual. Tighten screws to secure.
If using an AC/DC adapter, plug in at this time.
CAUTION! Do not exceed 12–24 VAC/DC
input! Doing so may damage receiver unit!
2. Mount Receiver 300 unit inside gate or door
operator near control circuit board using
Tek screws, zip ties, or other means of securing.
CAUTION! The receiver is not weatherproof.
Mount inside a weatherproof enclosure to
protect internal components from damage!
3. Securely connect included antenna to coaxial
connector on bottom end of Receiver 300 unit.
Slide rubber sleeve over connector to protect.
If mounting the Receiver 300 unit inside a
metal enclosure, such as a gate operator
housing, you will need the Security Brands
Antenna 300 (14-ANT300), which comes
with a 15-foot coaxial cable, antenna, coaxial
connector, mounting bracket, and hardware
for mounting outside the metal enclosure.
HOW TO USE
1. Make sure you are in range of Receiver 300 unit.
2. Press button on remote linked to receiver.
3. Receiver will respond and operate gate/door.
NOTE: If the receiver does not respond, make sure it
has power and that the antenna is not inside a metal
box or otherwise blocked. If the receiver still does not
respond, make sure the DIP switch positions on both
the receiver and the remote(s) match.
Other Security Brands Receiver manuals
