SecurView SecurView OEM-6214 User manual

INSTALLATION INSTRUCTIONS:
The OEM-6214 is a special designed OEM camera with a custom mounting bracket that allows
it to be mounted easily to the vehicle. It is designed to take the place of the license plate
illumination lamps on the Honda Accord 2008-2011 vehicles with minimal installation time and
with no special tools required for the job. Once installed, the camera looks completely factory
and is easy to keep out of sight.
FEATURES:
•Replaces the license plate illumination lamp when mounted
•The 170°ultra wide-angle
•Easily mounts to vehicle with minimal installation time
•Parking assist lines to help the driver accurately judge distance behind the vehicle
•Constructed of high-grade plastic
•Reverse image
•The OEM cam easily connects with other SecurView products such as any of the LCD
monitors. It can also be integrated with your existing OEM or aftermarket LCD/TFT
displays.
•The Securview™ OEM-6214 is designed specifically for the Honda Accord vehicle and
may not work well on other vehicles. Please check the vehicle before installing to make
sure the camera can be properly placed
OEM-6214
Wide-
Angle OEM
Camera

INSTALLATION
MOUNTING:
1. The OEM-6214 is design to be mounted on the License Plate bezel of a Honda Accord
vehicle. If you wish to mount this camera on any other vehicle, double check the mounting
location to see if the camera will fit on your vehicle in your location of choice.
2. Unclip and remove the factory license plate illumination lamp using a screw driver or panel
removing tool (STEP 1). Be cautious not to scratch the paint on the body surface.
3. Connect the license plate lamp illumination wires of the OEM-6214 to the factory license plate
illumination lamp harness that was connected to the factory lamp (STEP 2)
4. Route the wiring harness into the vehicle (STEP 3). There may be an existing factory rubber
grommet that you can use to run the wiring into the trunk area. If you have to drill a hole,
make sure to double check behind the drilling location before drilling. Once the hole is drilled
and the wiring is run into the vehicle, seal the edges of the hole with silicon or caulking to
prevent moisture damage.
5. Snap the camera securely into place in the mounting location (STEP 4).
NOTE: The interior panels of the trunk area will need to be removed in order to route the camera
cable into the car. This will also make it easier to remove the license plate lamp.
STEP 1 STEP 2
STEP 3 STEP 4
Snap the OEM-6214 camera into place
Remove factory
license plate lamp Connect the camera lamp illumination wires
Route the wiring
harness into the
vehicle
CAMERA:
1. The color CMOS camera is maintenance-free, waterproof (IP-68) and vibration resistant.
2. This camera is designed to work well in day time or night time conditions.
3. The camera is completely electronic. There are NO manual adjustments for focus, etc.

WIRING:
1. Carefully choose a hidden out-of-sight location for drilling the cable hole. Some vehicles may
have an existing hidden rubber grommet or plug available to avoid having to drill into the body.
Be sure to double-check for any wiring or obstructions behind the surface where you are going to
drill the cable hole. Make sure to seal the hole using silicon or caulking to prevent moisture
damage.
2. Choose a convenient place to run the camera cable up the left, right or center of the vehicle. As
a rule of thumb, try to avoid main factory harness looms that may contain high levels or RF noise
or interference.
3. You can connect the camera power at the rear of the vehicle behind the reverse lights. You may
also connect power inside the vehicle under the dash or in the trunk. The Red power wire goes to
Reverse Light +12V, and the Black wire to Ground.
4. The other pair of Red and White wires is for license plate illumination. Connect the Red wire to
the +12 volt license plate illumination wire in the factory light harness, and connect the White wire
to the Ground wire in the license plate illumination harness
5. Run the Yellow RCA video cable to the monitor’s video input or reverse camera input.
MONITOR
Connect to +12V
Reverse Light
RED
WIRE
BLACK
WIRE
Ground
OEM-6214
CAMERA
YELLOW RCA
Connect to
Monitor
YELLOW RCA
RED POWER PLUG
RED WIRE
WHITE WIRE
Ground
Connect to +12V
License Plate
Illumination Wire
TECH SUPPORT: [phone]

DISCLAIMER:
Under no circumstances shall the manufacturer or distributor of the Securview™ be held liable for
consequential or incidental damages sustained in connection with the use of the Securview™ Rear
Vision System. The Securview™ is designed as a safety enhancement device and is in no way intended
as a replacement for rear-view mirrors, side-view mirrors or physically checking the surroundings when
backing a vehicle. Always check surroundings for safety when backing! Objects on the monitor are
closer than they appear. For the best fit, modification of the vehicle license may or may not be
necessary. It is the sole responsibility of the vehicle owner to check and verify any and all State or
Federal Motor vehicle codes with regards to modifications of vehicle license plates. The manufacturer of
the Securview™ assumes no liability or responsibility whatsoever with regards modifications of the
license plate.
www.crimestopper.com
[e-mail]
Phone [phone]
FAX [phone]
© 2011 Crimestopper Security Products
5-18-2011
SPECIFICATIONS:
1/4 Inch Color CMOS Sensor Video Output: 1.0 V P-P composite (75 Ohm load)
Dimension (In.): 1⅝"(L) × 2⅝"(W) × 1⅜"(D) Supply Voltage: +12VDC
Weight: 4 Oz. Power Consumption: 70mA
Pixels: 656 (H) x 492 (V) Shutter: 1/50 s – 1/100000s
Resolution: > 250,000 pixels White Balance: Automatic
420 TV lines Gamma Correction: 0.45
Minimum Illumination: 0.5 LUX / F 1.2 S/N Ratio: More than 48dB
Lens Type: Wide Angle Operating Temp: -22° to 176° F (-30° to 80° C)
Horizontal Angle: 170° Gain Control: Automatic
Vertical Angle: 90°