SecurView SecurView SV-6827 User manual

INSTALLATION INSTRUCTIONS:
The SecurView™ SV-6827 is a lip mount style camera that is designed specifically for mounted
underneath the side view mirrors of a vehicle to give the driver a full length view of the vehicle.
The camera lens can be slightly adjusted for a better viewing angle and all wiring and mounting
hardware is set behind the mounting surface so that only the camera can be seen once it is
installed on the vehicle.
FEATURES:
•The 170°ultra wide-angle
•Designed for left, right or rear vehicle installation
•Can be mounted underneath side view mirror or lens can be rotated for sideways
mounting on the side of the vehicle
•Reverse image
•Constructed of high-grade plastic
•Requires a hole to be drilled for installation
•Easily connects with other SecurView™ products such as any of the LCD monitors. It can
also be integrated with your existing OEM or aftermarket LCD/TFT displays.
•Waterproof Design (IP68)
SV-6827
170° Embedded Lip
Mount style camera

INSTALLATION
MOUNTING:
1. Find a suitable location underneath the side view mirror or on the side of the vehicle or also
on the rear of the vehicle under the license plate bezel to mount the camera
2. Make sure the mounting location that you choose is on a flat surface so that when the camera
is installed there will be no uneven gaps around the edges.
3. Once you get the camera in a suitable location, drill a small hole for the mounting hardware to
fit through the surface. (Remove the locking nut before you feed the mounting post through
the hole.)
4. Route the wiring through the side mirror and through the door into the vehicle or if you
mounted the camera in the rear of the vehicle, route the wiring through the rear of the car.
You might want to seal the hole once you route the wiring through to prevent leaking or
moisture damage.
5. Use the supplied 3M tape to securely mount the camera in place on the flat mounting surface
6. Tighten the lock nut down on the other side of the mounting surface to make sure that the
camera is completely secure.
Video / Power
Cable
Mounting Surface
Locking Nut
SV-6827 Camera
A hole will need to be drilled for
the camera to mount properly
3M Tape
NOTE: Make sure to use a drill bit that is not bigger that the locking nut so that the camera can be
fastened properly to the mounting surface.

WIRING:
1. Carefully choose a hidden out-of-sight location for drilling the cable hole. Some vehicles may
have an existing hidden rubber grommet or plug available to avoid having to drill into the body.
Be sure to double-check for any wiring or obstructions behind the surface where you are going to
drill the cable hole. Use the rubber grommet to make a watertight seal for the cable where it
passes into the vehicle.
2. Choose a convenient place to run the camera cable through the left mirror, right mirror or through
the trunk if you are mounting the camera in the rear of the vehicle. As a rule of thumb, try to avoid
running the video cable next the any main factory harness looms that may contain high levels or
RF noise or interference.
3. If you are installing the camera for reversing purposes, you can connect the RED wire of the
camera to the reverse light wire in the rear of the vehicle. If you are using the camera for a side
view camera, you can connect it to a +12 volt ignition source. Connect the BLACK wire to chassis
ground
4. Run the Yellow RCA video cable to the monitor’s video input or reverse camera input.
MONITOR
RED WIRE
BLACK WIRE
Ground
SV-6827
YELLOW RCA
Connect to
Monitor
Connect to +12 volt
Ignition or Reverse Light wire
CAMERA:
1. The color CMOS camera is maintenance-free, waterproof (IP-68) and vibration resistant.
2. This camera is designed to work well in day time or night time conditions.
3. The camera is completely electronic. There are NO manual adjustments for focus, etc.
TECH SUPPORT: 800-998-6880

DISCLAIMER:
Under no circumstances shall the manufacturer or distributor of the Securview™ be held liable for
consequential or incidental damages sustained in connection with the use of the Securview™ Rear
Vision System. The Securview™ is designed as a safety enhancement device and is in no way intended
as a replacement for rear-view mirrors, side-view mirrors or physically checking the surroundings when
backing a vehicle. Always check surroundings for safety when backing! Objects on the monitor are
closer than they appear. For the best fit, modification of the vehicle license may or may not be
necessary. It is the sole responsibility of the vehicle owner to check and verify any and all State or
Federal Motor vehicle codes with regards to modifications of vehicle license plates. The manufacturer of
the Securview™ assumes no liability or responsibility whatsoever with regards modifications of the
license plate.
www.crimestopper.com
[e-mail]
Phone [phone]
FAX [phone]
© 2012 Crimestopper Security Products
4-20-2012
SPECIFICATIONS:
1/4 Inch Color CMOS Sensor Video Output: 1.0 V P-P composite (75 Ohm load)
Dimension (In.): ⅞"(L) × 2"(W) × 1¼"(D) Supply Voltage: +12VDC
Weight: 4 Oz. Power Consumption: 70mA
Pixels: 628 (H) x 582 (V) Electronic Shutter: 1/50 s – 1/100000s
Resolution: > 250,000 pixels White Balance: Automatic
420 TV lines Gamma Correction: 0.45
Minimum Illumination: 0.2 LUX / F 1.2 S/N Ratio: More than 48dB
Lens Type: Wide Angle Operating Temp:-13° to 178° F (-20° to 75° C)
Horizontal Angle: 170° Gain Control: Automatic
Vertical Angle: 120°