SecurView SV-6919.IR User manual

INSTALLATION INSTRUCTIONS:
The SV-6919.IR SideCam™ is night-vision equipped CMOS color camera designed specifically
for sideways mounting on the vehicle. The sideways mounting style makes it a perfect
application for bigger vehicles to allow the drivers to see all the way down the side of the
vehicle. It can be used on all types of vehicles such as: Semi Trucks, Motor Homes, Trailers,
Vans, Buses, Limousines, or even on a regular car. It is available in right side or left side mounts
and can be easily angled up or down for better viewing angle.
FEATURES:
•Sideways mounting style CMOS color camera
•120° Viewing Angle
•Equipped with Infra Red LED for Night Vision
•Available in right side mount (SV-6919.IR.R) or left side mount (SV-6919.IR.L)
•Perfect for use with any DVR system
•Perfect for bigger vehicles (Semi Trucks, Motor Homes, Limos, Buses, Etc)
•Normal or reverse Image selectable
•Constructed of high-grade plastic
•Swiveling lens makes it easy to adjust the viewing angle
•Provides extra security when making wider turns especially on bigger vehicles
•Waterproof Camera Design (IP68)
SV- 6919.IR
SideCam™
Sideways Mounting CMOS
Color Camera with Night
Vision

INSTALLATION
MOUNTING:
1. Locate a suitable place to mount the camera.
2. Remove the hex assembly screws from the SV-6919 camera housing. This will allow the
Camera housing and the Mounting Bracket to be separated from each other (STEP 1)
3. Remove the camera housing to expose the inner side of the mounting bracket.(STEP 2)
4. Be sure to double-check behind the mounting surface to make sure that you will not be drilling
into anything behind it.
5. Place the mounting screws in the designated screw holes on the mounting bracket (STEP3)
and drill them into the mounting surface to secure the mounting bracket to the vehicle.
6. Drill the hole for the camera wiring harness and route the harness through the cable hole on
the mounting bracket (STEP 3) and through the mounting surface. Once the mounting bracket
is secured tightly down to the vehicle, the rubber molding on the edges of the bracket will seal
the holes to prevent moisture damage or leaking.
7. Reassemble the camera housing to the mounting bracket (STEP 4).
STEP 1 STEP 2
STEP 3 STEP 4
Replace camera housing and hex screws
Camera Lens Camera Housing
Mounting Surface Mounting Screws
Cable
Install mounting screws in the designated screw
holes on the mounting bracket (Arrows)
Remove hex screws from camera housing Remove camera housing from mounting bracket
Mounting
Bracket
Cable
Hole
CAMERA:
1. This color CMOS camera is maintenance-free, waterproof (IP-68) and vibration resistant.
2. This camera is completely electronic. There are NO manual adjustments for focus, etc.
3. This camera is equipped with Night Vision to give you better lighting at night time. This plus
the vehicle’s reverse light and the ambient lighting in the area should make it perfect for night
time driving.

WIRING:
1. Be sure to double-check for any wiring or obstructions behind the surface where you are
going to drill the cable hole. Once the camera is secured to the vehicle, the rubber edges of
the mounting bracket will form a watertight seal to prevent moisture damage and leaking.
2. Choose a convenient place to run the camera cable up the left, right or center of the vehicle.
As a rule of thumb, try to avoid main factory harness looms that may contain high levels or RF
noise or interference.
3. You can connect the camera power at the rear of the vehicle behind the reverse lights. You
may also connect power inside the vehicle under the dash or in the trunk. The Red power
wire goes to Reverse Light +12V, and the Black wire to Ground.
4. Run the Yellow RCA video cable to your monitor’s video input or camera input of your LCD
monitor or DVR system
5. The small white plug is for normal / reverse imaging. Clip on the plastic jumper cap to reverse
the image or leave it disconnected for normal image.
NOTE: On the extension cable for the camera, there is a White RCA connector alongside the
yellow RCA video connector. You DO NOT need to connect the White RCA connector to
anything
Yellow Video RCA
Power
Connector
Black
Red
+12V Reverse
Light wire
Ground
SV-6919.IR
CAMERA
Normal / Reverse
Image Plug
MONITOR
REVERSE (MIRROR) IMAGING:
The SV-6919.IR Camera has built-in circuitry to “mirror” the image so objects on the right of vehicle
appear on the right and objects on the left appear on the left when looking at a standard monitor. If
your existing monitor or in-dash monitor has a reverse camera input where the monitor itself performs
the mirror image, then your picture will not be correct. If this happens, the SV-6919.IR camera has a
jumper plug that can be connected to reverse the image back to normal. (See Wiring Diagram)
TECH SUPPORT:
800-998-6880

DISCLAIMER:
Under no circumstances shall the manufacturer or distributor of the SV-6919.IR be held liable for
consequential or incidental damages sustained in connection with the use of the SV-6919.IR Rear Vision
System. The SV-6919.IR is designed as a safety enhancement device and is in no way intended as a
replacement for rear-view mirrors, side-view mirrors or physically checking the surroundings when
backing a vehicle. Always check surroundings for safety when backing! Objects on the monitor are
closer than they appear. It is the sole responsibility of the vehicle owner to check and verify any and all
State or Federal Motor vehicle codes with regards to modifications of the vehicle.
www.crimestopper.com
[e-mail]
Phone [phone]
FAX [phone]
© 2011 Crimestopper Security Products
4-18-2011
SPECIFICATIONS:
1/4 Color CMOS Sensor Video Output: 1.0 V P-P composite (75 Ohm load)
Dimension (In.): 2½"(L) × 2"(W) × 3½"(D) Supply Voltage: +12VDC
Weight: 10 Oz. Power Consumption: 200mA with Night Vision
Pixels: NTSC: 510 (H) x 496 (V) Electronic Shutter: 1/50(1/60) s – 1/100000s
PAL: 628 (H) × 586 (V) White Balance: Automatic
Resolution: > 275,000 pixels Gamma Correction: 0.45
More than 420 TV lines S/N Ratio: More than 48dB
Minimum Illumination: 0 Lux / F 1.2 Operating Temp: -4° to 158° F (-20° to 70° C)
Lens Type: Normal Gain Control: Automatic
Horizontal Angle: 120°
Vertical Angle: 90°