Seg LED 2612 QD User manual

66cm (26") LED TV
66cm(2 6")
LED 2612 QD

EN
Remote control instructions in DTV/USB mode
Mute
Unmute sound Available in all modes.
SOURCE
Display / Hide Source Menu.
Power button
On/Off Standby mode.
Menu
Display / Hide main menu, step back one menu, exit menu.
Help
Display / Hide the Help Menu.
Quick start
Display / Hide the Quick start menu.
Short cut to ATV source. Sequences ATV, DVBT-TV, DVBT-
Radio, ATV
Shortcut to DVBS/DVBS2 source.
Shortcut to DVBC source
(Timeshift)*
Play or pause.
Press to enter Timeshift, the image paused and it start
record from the paused position.
Stop playing or stop recording.
Fast reverse and Fast forward.
Previous / next chapter in USB mode or play the Previous
/next scene of the recorded programs, jump by 30 seconds.
VOL+/VOL-
Press to increase / decrease the sound level.
CH+/CH-
When watching a channel, changes the channel.
NUMBER BUTTONS
Press 0-9 to select a TV channel directly when you are
watching TV. The channel change after 2 seconds.
* depending on the model

Remote control instructions in TELETEXT mode
Coloured
Fast text when in update mode and fast text links present.
Can be used for other functions in Hold mode.
Exit
Exit text mode.
(Index)
Index page (page 100)
Up/Down
Select +/- Page in Hold mode.
Left / Right
Hold main page and select sub pages using Red / Green
soft.
OK
Hold page and Expand TOP / Bottom / Full , Use TXT for
Update.
NUMBER BUTTONS
Press 0-9 to select a teletext page.
Press this button to show hidden text (e.g. the solutions for
TV quiz shows). Press it again to hide the text.
SUB
Subtitle display/ select button (can display/Hide a menu).
TXT
Text / Mix / TV( always in Update mode)

EN
Installing Batteries in the
Remote Control
1. Remove the battery compart-
ment cover at the rear of the
remote control by pushing
the retaining clip forward and
pulling up.
2. Install the supplied batter-
ies, ensuring the polarity
matches what is shown in the
battery compartment.
3. Replace the battery compart-
ment cover.
Aerial connection
WARNING! ENSURE THE TV AND ALL ANCILLARY
EQUIPMENT IS UNPLUGGED FROM THE MAINS BEFORE
MAKING ANY CONNECTIONS!
Connecting the TV Antenna
Connect the TV antenna to the aerial socket with a 75
ohm co-axial plug. For best results use a high gain TV
aerial, preferably roof or loft mounted.
To improve picture quality in a poor signal area, pur-
chase and inst r.
If the antenna needs to be split for two TVs, use a 2-
Way Signal Splitter (not supplied).
Using the Remote Control
To use the remote control point it at the TV and press the
required buttons. You must be within 6 meters and at an
angle of less than 30 degrees from the center of the TV.
NOTE: Sunshine or other strong light sources may inter-
fere with the signal from the remote control. In this situa-
tion turn the TV away from the light source.
WARNING! DO NOT LEAVE BATTERIES IN
THE REMOTE CONTROL FOR EXTENDED
PERIODS AS THEY CAN LEAK OR CORRODE
CAUSING DAMAGE TO THE REMOTE CON-
TROL. CHECK THEM PERIODICALLY AND
REPLACE THEM AS REQUIRED.
WARNING! DO NOT MIX BATTERY TYPES.
WHEN INSERTING BATTERIES, REPLACE
ALL BATTERIES AT THE SAME TIME. DO
NOT MIX OLD AND NEW BATTERIES.
WARNING! EXHAUSTED BATTERIES MUST
BE TREATED WITH CARE AND DISPOSED
OF ACCORDING TO ANY SAFETY OR RECY-
CLING REGULATIONS IN FORCE IN YOUR
LOCAL AREA, NEVER DISPOSE OF BATTER-
IES INTO GENERAL WASTE, OR FIRE.
WARNING! NEVER EXPOSE BATTERIES TO
EXCESSIVE HEAT SUCH AS SUNSHINE, FIRE
OR THE LIKE.
Connecting external devices
This instruction manual shows the simplest and most ef-
fective way of connecting your TV to ancillary equipment.
Alternate methods are listed below.
HDMI Lead
You can connect this TV to a compatible device using a
HDMI lead. This method will give the best picture.
Connect the cable from the HDMI equipment to the TV
HDMI socket.
SCART Lead
You can connect this TV to a compatible device using
a SCART lead. The connection uses component video
signals, i.e. the red, green and blue (RGB) content of the
video are sent on separate signals.
VGA Cable
You can use your TV as a monitor for your personal com-
puter by using a VGA cable. Sound from your personal
computer may also be played through the TV.

EN
Connecting external devices
CONNECTIONS
Caution:
Before connecting external devices:
Makes sure to disconnect the appliances from the
power supply in order to avoid any potential damage
from occurring.
Make sure to establish the required connection.
Make sure that the connectors are properly and cor -
rectly attached before connecting the appliances to the
power supply.
PC connection
As PCs are sometimes still supplied with a ‘conventional’
CRT monitor, you may need to adjust the display set-
tings of your PCs graphics card, otherwise the pictures
may not appear correctly. Switch on your PC (still with
your original monitor connected) now select the screen
resolution, and select 60Hz refresh rate. Switch o your
PC, then connect it to your TV while both appliances are
still switched o.
VGA, HDMI PC Connection
Use a PC-VGA cable (not supplied) to connect the TV to
your PC. You can also use an HDMI cable to connect to
your PC (if your PC Graphic card supports HDMI). When
the HDMI cable is used, the PC audio cable is no longer
required. If you use the HDMI to DVI cable, you will need
to use the PC audio cable. Connect all cables carefully
and do not bend or break the connector pins.
When using the VGA cable
Switch on the TV
Switch on the PC
Select PC/VGA as input source
When using the HDMI cable
Select HDMI as input source
VGA cable
HDMI to DVI cable
Audio cable
HDMI to HDMI
(All illustrated cables are not supplied)
Satellite connection
DVB-S/DVB-S2 Signal
Connect the DVB-S/DVB-S2 signal to the SATELLITE LNB
on the TV SET. Select the SATELLITE input source using
the DVBS/DVBS2 button on the remote control.
Note: If there is no DVBS(S2) reception, please check
whether there is any problem (such as a short-circuit) on
the F-type connector, on the LNB cable, the multi-switch
etc. of your satellite antenna system. In this case, please
disconnect the TV set from the antenna system. If neces-
sary, c technician to solve the problem.
Name Function Description
HDMI Connect to the HDMI output of your
DVD or Satellite Box
SAT LNB Con-
nection Connect to Satellite signal
VGA (PC IN) Connect to the PC VGA output to dis-
play PC graphics
PC-IN PC Audio input
Mini YpbPr Connect to the YPbPr output on exter-
nal devices
Mini AV Connect to AV output on external
devices
SCART Connect to the SCART input / output
of external devices
RF Connect to TV signal cable
Head phone Connect Head phone
CI / CI+ CI slot (Pay as you view card slot)
Coax Output t
USB Media playback
POWER Connect to power supply
INI
P P
INI
V
USB DVBS-2 Common Interface Headphone out

Connecting Video camera and Video recorder
Video camera
Connect the AV cable to the TV and to the video cam-
era.
Turn on both video camera and the TV.
Select AV/CVBS source
You can now see the playback picture from the video
camera. Note:
To connect the video camera using other cables, refer
to the video camera instruction manual.
Video recorder
Connect the Scart cable to the TV and video recorder.
Turn on both video recorder and the TV.
Select Scart source
You can now see the playback picture from the video
recorder.
Note:
To connect the video recorder using other cables, refer to
the video recorder instruction manual.
Scart cable
Video recorder
Video camera
(Mini AV cables are supplied)
Mini Audio and Video transfer
cable
Connecting an audio system
You can supply the TV sound to the stereo system (A) with
the Scart socket. Use a special Scart cable SCART to RCA.
(Please consult y structions for details). If you
have a surr coder (B) Use the
Scart cable or the special Scart cable Scart to RCA.
Scart to RCA cable
Scart cabl
Coax cable
e
(All illustrated cables are not supplied)

EN
CI+Slot
CAM
SmartCard
1Turn on the TV and ensure ‘DTV’ Source is selected
2If the CAM is detected the TV will display the following
message on the screen. “Common Interface Module
inserted “wait for a few moments until the card is
activated
3Select the relevant digital Pay Per View channel
4Detailed information on the Smart Card in use is dis-
played
5Press the Ok button to access the card menu. Refer to
the Module Instruction Manual for setting details
6When the module is removed, the following message
will appear on the screen. “Common Interface module
Press the power button on the LED TV or the POWER but-
ton on the remote control, the standby indicator will light
green
To turn off the LED TV
Press the power button on the LED TV or the POWER but-
ton on the remote control, the standby indicator will light
red
When you initially turn on the LED TV you will see the first
timeinstallationmenuasbelow
ATV (Analogue Television) is used for Analogue Cable
systems
DVB (DTT - Digital Terrestrial Television, DVB-T) is used if
you have an antenna receiving signals from a terrestrial
transmitter
Cable is used for Digital Cable systems (DVBC)
Satellite dexifadeenuoY.E2.91artsA
rofteserpsi dish
with a universal LNB. To install any other satellites use
the full satellite installation menu
the Conditional Access Module (CAM) and Smart Card
in order to view the pay TV programmes and additional
services. Contact your Pay Per View TV service provider
to get more information about the modules and subscrip-
tions
NOTE: Conditional Access Module and Smart Cards are
sold separately
WARNING! SWITCH OFF YOUR TV BEFORE ANY MODULE
IS INSERTED INTO THE COMMON INTERFACE SLOT,
THEN ADD THE SMART CARD TO THE CAM
Ensure your aerial, cable or dish is plugged in to the TV
and then press OK again
The TV will start to install the service you have selected
This could take some time depending on your selected
service
You can tune an additional service at any time by pressing
the Quick Start button.
CommonInterfaceSlot
USING YOUR COMMON INTERFACE SLOT
This TV set features a CI+slot and supports the following
digital standards:DVB-T, DVB-S(S2) and DVB-C.
Common Interface
The Common Interface (CI+) slot is designed to accept
removed“.
Auto installation setup
Power On /Off the LED TV
To turn on the LED TV
Press OK button and you will see the following menu.
Select Home mode and confirm with OK button.
Use the left/Right/Down keys to select your language
and country use the up/down keys to select the type of
service you want to install. You can only install one service
at a time but you can return to this menu in order to install
an additional service by pressing the Quick Start button.

EN
Unlike QUICKSTART the satellite search will search the
whole satellite for channels and will not be instant.
Also the channels will appear in the order on the satellite
and not the pre-set order.
Auto search replaces any previous searched channels
with those of the new search. To add an extra satellite if
you have a suitable Dish/LNB/Switch you must use the
Dish Installation menu.
DTV (DVBT) Manual Tuning
You can manually tune DTV channels in the TV SETTINGS
menu. Press the Left/Right arrow buttons to select the
channel you wish to tune, then press OK button to scan
for the channel.
You can manually tune CADTV channels in the TV SET-
TINGS menu.
Note: for more information about the channel parameters
(frequency, symbol rate and QAM type), please check with
your cable TV provider.
Frequency
Select Frequency using the buttons.
Symbol (ks/s)
Select the Symbol (ks/s) using the buttons.
QAM Type
Select the QAM Type using the buttons
ATV (analogue cable TV) Manual Tuning
You can manually tune ATV channels in the TV SETTINGS
menu.
Storage to
Press the buttons to change the numbered location
of the found channel.
System
Select the system using the buttons.
Current CH
Displays the current channel number, press the buttons
to choose the channel you wish to modify.
Search
Press the buttons to scan through the frequencies to
ew channels.
Fine tune
In case of bad reception, you can press the buttons to
mak stments to the tuning. After manual tun-
ing is complete, please press the RED button to save any
found channels.
Press / to select DVB Select type, Country and Tune
Type, press OK to start scanning.
If you select ATV+D rst 50% of the processing is
for ATV tuning, while the second 50% represent DTV tun-
ing. When ATV tuning, you can press MENU to Skip ATV
tuning and start DTV tuning or press EXIT to exit tuning.
During the channel search a preview of the already-found
channels is displayed.
CADTV (DVB-C) Manual Tuning

navigate through the menu
Delete
Press the RED button to delete the highlighted channel, a
Move
Press to select the channel, press yellow button to
enter the move mode, then press to move the chan-
Skip
Press to select the channel you wish to skip.
channel name and the channel will be skipped when you
scroll through the channels.
main menu.
Rename (Only available in ATV)
Modify current channel name.
Press the button to enter RENAME mode, then use
the buttons to change name. Press the green
Signal Information
channel /network/modulation/quality /strength.
Cl Information
-
channels is not possible.
Power-Off-No-Signal-Down
If no valid input signal is detected, the TV set will toggle to
Auto-Power-Down
the last channel switching, the TV set will automatically
toggle from On to standby mode. Prior to this automatic
toggling, a message will be displayed allowing you to
Guide (EPG – Electronic Program Guide)
the Electronic Program Guide. EPG contains a 7-day
programme preview as long as the selected channel
supports this function. If there is more information about
a programme, press the and buttons to scroll
-
able number of characters is limited.
Favourite Lists
-
ton to add it to the list of favourite channels. To remove a
channel from the favourite list, select the desired channel
create an own favourite list for each tuner module.
Dish Setup
section.
or with a different LNB you will need to use this sec-
tion.
3. If you have a motorised Dish with a DiSEqC rotator
and wish to tune more than one satellite you will need
this section.
4. If you are on a DiSEqC switch system you will need
this section.
long as you know what satellite your dish is aligned with
Installation of 3 & 4 require an experienced user or
engineer.
PROGRAMME EDIT
Favorite
Press the green button to set the favorite channel.
5V antenna power
Press button to turn on or off.
Software Update (USB)
1. Download the software to the usb device, then insert the
usb device to the unit.
2. Press the Menu button to select the TV SETTINGS menu.
3. Press the buttons to select Software Update(USB) and
then press the OK button to update software .
4. when the updating is completed, the unit will be reset to
standby mode.

EN
To set a different Satellite or LNB
Select Satellite mode, press MENU key, navigate down to
the Dish Setup option, press OK. You will see the Satellite
Dish Setup menu.
To set Multiple Satellites and LNBs (only possible
on multi-LNB dish, switch systems)
Use buttons to select the satellite to which your dish
is aligned. Press OK. An arrow will display against the
chosen satellite.
Press button to navigate to LNB section of the menu.
Select the LNB type and settings for your LNB.
Press the Exit button and the button to select the sec-
ond satellite.
Use buttons to select the second satellite. Use
keys to select the satellite to which your dish is aligned.
Press OK. An arrow will display against the chosen satel-
lite.
Press button to navigate to LNB section of the menu.
Select the LNB type and settings for your second LNB
and switch settings.
Press the Exit button and the button.
Press the blue Key twice to search the satellite channels.
A full description of the advanced Dish set up for
multiple satellites using DiSEqC switches and DiSEqC
positioner follows. This should only be attempted by
experience users.
The Dish set up main menu page displays the main inter-
face. The interface consists of Satellite List, Transponder
list and Dish/LNB parameter list
Satellite List
The Satellite list displays the satellite names.
Satellite Edit
No. The current list number of the selected satellite Sat-
ellite name. The No. cannot be edited.
Satellite name: Press the green button to open the edit
menu explained below.
Extend: Extended characters
Caps On: Change character case. Press OK button to
select.
Back: Delete letters, press OK to c
OK: Sure to set the naming of the satellite, and return to
Edit Menu
Cancel: Return directly back to edit menu.
Longitude Direction: Added to determine the location of
the satellite. Use the arrow buttons to select West/
East.
Longitude Angle: Input Longitude. By moving the cursor
tu buttons to enter the satellite longitude.
Band: band selection. Press to select.
For editing via the on-screen keyboard, press the but-
ton.
In the input frame, use and OK button to select
characters.
Input Frame (On-screen keyboard)

Delete Satellite menu
Press the YELLOW button, the c -
r. Press OK to de ete.
Add Satellite
Press the RED button t
NO: s r c
ted.
Adjus rter ccor to the
sre ress OK t ve or
ress EXIT o c c
A ne s t
tte.
Transponder List
st sho r rs or the se ect t te.
Edit Transponder menu
Press GREEN button to enter Tr
No. s r. Nr. c -
ted
Frequency: Set the do requency.
Symbol (ks/s): te.
Polarity: t v c
Delete Transponder
Press the YELLOW button, the c -
r. Press OK to de ete.
Add Transponder
Press RED button to ent r
No. ted.
Frequency: Set the do requency.
Symbol (ks/s): te.
Polarity: t v c
(khz)

EN
Dish Parameter description
LNB Type: LNB Frequency
Highlight the LNB Type , and use the buttons or Ok
to enter submenu then you c rameters.
LNB Power: Polarization switching power supply, Press
to select On/Off.
On: Allowed to receive Horizontal / Vertical Polarization
program.
Off: out-off of supply.
22KHz: The level of the LO switch / DS switch ( Require
the user to have installed 22KHzSatellite signal switch).
Press to select Auto/On/Off.
Auto: Automatically issued 22 KHz pulse signal to control
switching.
On/Off: Manual control switch.
Tone burst: Double Single Switch (Require users to install
Tone burst switch), Press to select Burst A/Burst
B/None.
Burst A /Burst B: Manually switch the satellite A/B.
DiSEqC1.0: 4 select 1 switch ( Require the user device
support DiSEqC 1.0 protocol). Press to select LNB1/
LNB2/ LNB3/LNB4/None.
LNB1/LNB2/LNB3/LNB4: Corresponding to a satellite ,
After selecting the corresponding list will appear in the
satellite list.

DiSEqC 1.1: 16 select 1 switch ( Require the user device
support DiSEqC1 .0 protocol) Equipment needs support
DiSEqC 1.1 protocol, Most control 16 LNB. Press to
select LNB1~LBN16/None.
LNB 1-LNB 16: Corresponding to a satellite, After select-
ing the corresponding list will appear in the satellite list.
Motor: Control of multi-satellite polar (Require the user
device support DiSEqC1.2 or DiSEqC1.3 protocol), Left
and right buttons to select DiSEqC1.2/ DiSEqC1.3/None.
DiSEqC1.2: DiSEqC1.2 Protocol selection
DiSEqC1.3: DiSEqC1.3 Protocol selection
For Mot te “DiSEqC1.2“ , Operating Instructions:
Press RED button to enter “Set Limit" menu.
Press OK button to enter Set Position menu.
Move Continue: Control of the east or the west continued
to turn the polar axis to the desired position.
Move Step: Control of the east or wes xed polar
axis step rotation.
Set West Limit: The current position is set to the maxi-
mum point of the west.
Set East Limit: The current position is set to the maxi-
mum point of the east.
Goto Reference: Back to the default values.
Disable Limit: Abolish the current limit set.
Move Auto: East or west of Automatic Control continued
to turn the polar axis to the desired position.
Move Continue: Manual control of the east or the west
continued to turn the polar axis to the desired position.
Move Step: Control of the east or wes xed polar
axis step rotation.
Store Position: Save the current rotation angle of polar
axis.
Goto Position: Control the polar angle automatically to
the previously saved.
Goto Reference: Control the angle of polar axis automati-
cally to the default. When Mot te “DiSEqC1.3“.
Press RED button to enter “Set Limit“ and Mot
as “DiSEqC1.3“ “Set Limit’ menu same.
Press GREEN button to enter Set Location menu.
Location: Select the user area or similar areas, if the user
is not in the system default settings when in these areas,
can select Manual custom settings.
Longitude Direction: Select the user area in the east
longitude or longitude.
Longitude Angle: Longitude angle. Select the user area in
which the longitude, Enter the appropriate values to move
the cursor.
Latitude Direction: Select the user area in the latitude or
latitude.
Latitude Angle: Select the user latitude area, Enter the
appropriate values to move the cursor.
Press OK button to enter Set Position menu.
GotoX

EN
Move Auto: East or west of Automatic Control continued
to turn the polar axis to the desired position.
Move Continue: Manual control of the east or the west
continued to turn the polar axis to the desired position.
Move Step: Control of the east or wes xed polar
axis step rotation.
Store Position: Save the current rotation angle of polar
axis.
Goto Position: Control the polar angle automatically to
the previously saved.
Goto Reference: Control the angle of polar axis automati-
cally to the default.
GotoX: Area based on user input parameters, Automati-
cally calculate the satellite over the area,
Control the polar axis rotation to the right place.
Scan Menu
When all the parameters after. Press BLUE button to Tun-
ing the setup menu to enter.
Scan Mode: Scan from Default, Blind Scan and Network
to select.
Default: Default search program.
Blind Scan: Searches all the programs for the LNB set-
tings. (This is a long sear
including new Channels).
Network: Search the known channel frequencies for the
selected LNB & Satellite settings at the time of manufac-
ture. (This will be the quickest search).
Channel Type: FTA (Free to Air) or ALL (Free to Air and
Pay Channels).
Service Type: DTV (DVB TV) or Radio (DVB Radio) or both
DTV & Radio.
Polarization: The LNB polarization: H (horizontal), V (ver-
tical) and AUTO depending on the LNB installation.
Menu Settings
Picture menu
Picture Mode: Choose from Standard, Dynamic, User and
Mild.
Note: Contrast, Brightness, Colour and sharpness are
only available and can be adjusted in the User mode
option in the Picture Mode Settings.
Contrast: Controls the difference between the brightest
and darkest regions of the picture.
Brightness: Controls the overall brightness of the picture.
Color: Control the color.
Sharpness: Increase this setting to see crisp edges in the
picture; decrease it for soft edges.
Tint: Controls the tint ( NTSC mode only).
Color Temperature: Choose from Medium, Cool, User
and Warm.
Red: Controls the red colour of the picture.
Green: Controls the green colour of the picture.
Blue: Controls the blue colour of the picture.
Aspect Ratio: Choose from Auto, 4:3, 16:9, Zoom1,
Zoom2, and Panorama.
Noise Reduction: Choose interference noise modes from
Off, Low, Middle and High.
GotoX

Home mode: Allows you to select among: Max Performance
mode, Home mode and Max Economy mode.
First Time Installation: This option allows you to reset the
tv to the default factory setting. Once activated the TV will
go to standby mode.
Coc -- -- -- --
C Setup
uto Stand n
Clock: Manually set the clock for ATV mode.
Auto Standby: Turn energy saving 4hr auto standby On/Off.
600s

EN
LOCK menu
The password must be entered to access the Lock Menu.
The default password is 0000. Once inside the menu you
can change the password to your own choice.
Lock System: Enables or disables the system lock. After
selecting ON, the settings made under “Lock Channel”,
“Parental Guidance” and “Hotel Settings” will be enabled
and applied.
Set Password: If you had already changed the password,
enter the current password.
Old Password: Enter the current password.
New Password: Enter the new password.
ew Password: Enter the new password.
You can use the Channel Lock to lock selected channels.
Press the buttons to select the desired channel and
then press the GREEN button on the remote control to
lock it. To unlock a previously locked channel, select the
channel and press the GREEN button.
Note: In order to view locked channels, you have to enter
your password.
Parental Guidance blocks programmes according to their
parental level. This feature is available only for digital TV
and the tuned-in channel must support it.
Hotel Setting: Opens the “Hotel Setting” menu.

Hotel mode
Restricts access to tuning menus, limitation of maximum
volume setting. Locks picture and signal menus.
Hotel Lock: Press the buttons to select the “Hotel
Lock“ option and then press to choose between the op-
tions ON or OFF. After selecting ON, the following options
except the “Clear Lock“ option are available.
Lock Channel: Press the buttons to select the “Lock
Channel“ option and then press to choose between the
options ON or OFF. After selecting ON, the TV settings op-
tions will not appear in main menu any more.
Set Source: Press the buttons to select the “Set
Source“ option and then press to choose a signal
source or OFF. This function lets you set the signal source
(DVB/Cable/Satellite/ATV/SCART/AV/YPBPR/PC/DVD/
HDMI/USB) to be used when powering on the
source or disable this function (OFF).
Picture Lock: Press the buttons to select the “Pic-
ture Lock“ option and then press to choose between
the options ON or OFF. After selecting ON, the Picture
menu options will not appear in main menu any more.
Key Lock: Press the buttons to select the “Key Lock“
option and then press to choose between the options
ON or OFF. After selecting ON, the front panel buttons
TV/AV/ Menu/CH+/CH-/VOL+/VOL of the device will be
locked.
Max.Volume: Press the buttons to select the “Max.
Volume“ option and then press to set the desired
volume. Then the output volume will never exceed the set
maximumvalue.
Source Lock: Press the buttons to select the “Source
Lock“ option and then press OK to enable the menu.
Press the button to toggle between ON and OFF. All
signal sources labelled ON will not be available any more
in the signal source selection menu.
Clear Lock: Press the buttons to select the “Clear
Lock“ option and then press to enable it. All hotel set-
tings will remain disabled until you enable the Hotel Lock
again.
Database export and import: Allows Picture, Sound, Op-
tions, Lock and Hotel menus to be copied from one set to
other sets, to make a group of sets all set up the same.
To export the settings t le on a USB memory: Connect
a USB memory stick to the USB1 port. Select “Database
export“. Press the button. When export is completed
successfully “Export Success“ is displayed.
To import the settings on
the memory stickcont le in USB1 of the new
TV. Select “Database import“. Press the button. When
complete the TV will turn off. When turned on again it will
hav rst TV.
QuickStart Lock: Press the buttons to select the
“QuickStart Lock“ option and then press to choose
between the options ON or OFF. After selecting ON, the
QUICK START button on the remotecontrol will be dis-
abled.
Menu Lock: Press the buttons to select the “Menu
Lock“ option and then press to choose between the op-
tions ON or OFF. After selecting ON, all submenus except
the “Lock“ menu will not appear in main menu any mor