Selecta SECURE06 User manual

Instruction Manual
MANSECURE06 REV A 11/08/2016
V60 MOTION ACTIVATED SECURITY CAMERA
SECURE06
VICTORIA (HEAD OFFICE)
Telephone: [phone]
Fax: [phone]
www.silvan.com.au
NEW ZEALAND
Hamilton, New Zealand
Telephone: [phone]
Fax: [phone]
www.silvannz.co.nz
SILVAN AUSTRALIA PTY. LTD.
ABN 48 099 851 144

Page
Product Warranty
3
Product Warnings
4
Product Information
5
Setting Up And Connecting
7
Functions Explained
8
Activating Live Mode
13
Reviewing Recordings On Camera
13
Managing Recordings
14
Reviewing Recordings Using External Equipment
14
Technical Specifications
15
Understanding Your Application
16
Express Setup Guide
18
Trouble Shooting
19
Contents

3
Silvan Warranty
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and for compensation for any
other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the failure does not amount to a
major failure.
We warrant our goods to be free from defects in materials and workmanship for the warranty
period of 12 months from the date the product is delivered to the consumer.
Silvan warrants its authorised Dealer, who in turn warrants the original purchaser (consumer) of
each new Silvan product that it will repair or replace the product, or, pay the cost of repair or
replacement, as determined by Silvan without charge for labour or any defective or
malfunctioning parts in accordance with the warranty limitations below.
This Warranty is in addition to any other rights and remedies available to consumers under the
law.
This Warranty Covers
Only conditions resulting directly from defects in workmanship or material under normal use and
service.
Warranty Exclusions
The Warranty does not cover:
•Conditions resulting from misuse, use of incompatible chemicals, exceeding machine
specifications including overloading, impact damage, negligence, accidental damage or failure
to perform recommended maintenance services as specified in the Owner/Operator Manual
applicable to the product.
•Damage caused by continued use of a product after initial failure
•Any product which has been repaired by other than an authorised Silvan service outlet in a way
which, in the sole and absolute judgment of Silvan, adversely affect its performance or
reliability.
•The replacement of maintenance items such as diaphragms, batteries, V belts and ground
engaging components, etc.
How To Claim Warranty
Return the goods to the place of purchase at your cost and within the warranty period along with
evidence of the purchase date. If the original supplier cannot be contacted, then contact Silvan as
below and we can direct you on how to proceed with your warranty claim.
How Your Claim Will Be Managed
The repair of a defective product qualifying under this warranty will be performed by any
authorised Silvan service outlet within a reasonable time following the delivery of the product, at
the cost of the owner, to the service outlet’s place of business. The product will be repaired or
replaced depending on the extent of the problem at the discretion of Silvan and the Silvan dealer.
Warranty

Warning! This product requires batteries to operate. Position batteries in proper polarity and do
not install batteries of different types, charge levels or capacities together as this risk
battery leaks, fire and or equipment damage.
Warning! Do not leave flat batteries within this device. Flat batteries have high risk of leaking and
the leaked chemicals are corrosive and damaging to equipment
Warning! Keep out of reach of children. Batteries if swallowed present a significant health hazard
Warning! Never allow an inadequately trained person to install or operate.
Warning! Cameras are often placed at elevated positions or in hard to access areas. Take suitable
safety precautions when installing to prevent acident or injury to the installer and ensure
that the installed dose not risk or endanger people or property if resulting in any kind of
failure.
Warning! This device can be used for Surveilance. The owner and operator are responsible for the
operation of this device and should ensure operation is compliant with relevant laws and
regulations.
Important Note! States and Territories may have their own laws covering the use of surveilance
devices. The State of Victoria uses the Surveillance Devices Act which may provide
useful guidance although it is reccomended to seek professional advice to ensure
applications are compliant with relevant legislation.
Important Note! This device when used for security applications should oly be one element of a
comprehensive security plan that encompases a range of security measures to
enhance the overall security. A comprehensive security plan should include
multiple overlapping elements that allows the system to continue working in
situations where an unexpected event takes place or where one element was not
operating or obscured from collecting useful data.
Other items that may contribute to a security plan with active and passive effects:
•Motion Activated Cameras
•Motion (Driveway) alert systems
•Area lighting
•Sturdy Chain Locks and padlocks
•CCTV systems
•Key Safes for ourdoor equipment
•Security warning signs
•Fences and closed gates
Important Note! Results may vary. The total setup of this product has great effect to the outcome
and the following should be considered to optimise preformance:
•Battery Quality
•Frequency of activity in the area
•Camera placement (area of view)
•Camera Settings
•Understanding type of activity
intended to capture
•Environmental movement such trees,
grass and bushes in the wind
•Ambient lighting such as street lights or
direct sun light to lens
•Distance to moving object and its size
•Reflective surfaces that may flare the lens
Safety Instructions
Ensure you have read and understood this manual and all other support
documentation in its entirety before attempting to operate or install. Read and
take note of all following safety warnings and notices.
Failure to comply with these warnings may result in serious injury or death.

5
The V60 Motion activated security camera is a self-contained camera system that operates
automatically according to the parameters as set. Using a PIR motion sensor the V60 activates
when motion is detected to record activity in the area.
Main Features:
•12 Mega Pixels Color CMOS
•60-degree field of view lens
•Fast trigger response (down to 0.6
seconds when using 2GB SD card)
•2.4” Color LCD Screen for setup and
image review
•Records Photos and/or Video
•Day & Night operation with No-Glow infra-
red night vision up to 15m
•Date Stamp recording to photos
•Battery Operated using 4/8 AA batteries
•IP54 Water and Dust resistant for outdoor
use
Other Features:
•Timer On/Off Function
•Password entry
•Serial number recording to images
•Audio recording to video
•Rugged plastic body with hinge open case and buckle closures
•Range of installation options: Strap mounting, Hook hang-able or optional camera mounting
bracket
General Information
Side View
Front View

General Information (cont.)
Interior View
Hook hanging
mount point
Hook hanging
mount point
Package Contents:
1x V60 Motion Activated Camera
1x USB Cable
1x Mounting Strap
1x 8GB SD memory card
1x Express set-up guide (with link to this operator’s manual)
Bottom View
Rear View

7
If you are not familiar with the operation of this camera, the following instructions will help you get a
quick overview. Before doing any operation, please make sure you have loaded batteries and plugged
the SD card correctly.
Power Supply:
◆To insert batteries in the device, first open the buckle of the device.
◆Insert 8 x 1.5 V AA batteries into the battery compartment (can fit 4 on left side to operate but
requires 8 battery for improved standby time).
◆Please pay close attention to the polarity, which is marked in the battery compartment.
Otherwise the device will not work and can be damaged.
◆Recommend you use best AA batteries designed for digital camera’s such as high performance
alkaline or lithium batteries. Alternatively, 8x high capacity rechargeable* batteries could be
used
◆You can also connect an external power supply and rechargeable battery; please sure that
voltage matches the camera.
◆An external power port at the base of the camera allows external batteries of the 6-12V range
to be connected such as a large rechargeable battery. When connecting an external power
supply or battery, the camera will use the external power preferentially.
Note: Rechargeable batteries are usually 1.2V cells instead of the 1.5V cells as specified. This
means that the total volts are lower than non-rechargeable batteries, so it is important to use 8
batteries for best performance.
Inserting SD Card:
Since the camera has no built-in memory, it can only work if an SD memory card is inserted.
◆To insert an SD memory card into the memory card slot of the device, push it into the slot until
it clicks into place.
◆To remove an SD memory card from the memory card slot of the device, press the protruding
edge of the memory card in a little way until it pops out. Then remove the card.
◆The contact surfaces of the memory card must be facing towards the front of the camera.
◆SD memory cards have a locking system to prevent accidental erasure of images. To protect
the card from write access, slide the switch on the side of the card to the "LOCK" position.
However, the camera can only save data onto the card if the switch is in the other position.
Note:
❖The device supports SD memory cards with a capacity of up to 32 GB.
❖To avoid malfunctions, keep the memory card away from moisture and avoid strong vibration,
dust, heat sources and direct sunlight.
❖Insert the memory card as indicated by the icon on the slot.
❖Never force the memory card into the slot. Never bend or twist the memory card.
❖Major fluctuations in temperature or humidity can lead to condensation which could cause an
electrical short-circuit. Keep the memory card in the protective case.
Setting Up And Connecting

Interface Overview:
The camera contains an LCD screen and keypad allowing settings to be adjusted or images
reviewed. After connecting a power supply, move the power switch to the "TEST" position which
turns on the LCD screen to allow test and setup functions.
Press the MENU button to enter/exit the main menu, navigate menu options through , , , .
All settings should press button to confirm. Always remember to press to save the change.
Otherwise you will lose your new setting.
NOTE: If you do not open the setting menu in 3 minutes, the camera will enter sleep mode, and
the screen will be turned off, but it will be turned on if any key pressed. If you do not open the
setting menu within thirty minutes, the camera will power off automatically.
Understanding The Screen Icons:
When the menus are closed the default view will be a live image from the camera where the
screen has different status icons.
Manual Photo/ Video Capture:
When the menus are closed the default view will be a live image from the camera.
1) Press button to switch to set manual video mode to shoot video clips.
As indicated top left of screen with video icon and resolution indicator.
Press the button to start video recording with a timer on screen.
Press the button again to stop the video recording
2) Press button to switch from video to photo mode to take still photos.
As indicated top left of screen with camera icon and resolution indicator.
Press the button to snap a single photo
The camera will automatically decide if to take a day or night shot when the
button is pressed. When shooting video, the camera will not change between day or night
mode during a recording. Hence a video beginning in night mode will continue in night mode
even if lighting changes in the testing period. For testing purposes to force a camera to change
between day/night mode the lighting in front of the camera must change enough before
beginning another recording.
Functions Explained
Indicates that the mode as
either photo or video when
taking images manually.
Specifies resolution that the
camera is set to.
E.g. 5M = 5-megapixel photo
720P = 1280 × 720 video size
Battery Status Indicator
The number indicates
how many photos or
video (in length) can be
stored on the remaining
memory of the SD card
SD indicates the SD card is
inserted
Indicates the current
temperature as detected
by the camera
Live Camera View

7
Press the MENU button to open the settings menu.
1) Press the / buttons to select the desired menu entry which you can then activate with the
OK button. If you change settings, you must always confirm your changes with "OK". Use the
MENU button to navigate one menu level backwards.
Mode:
To select whether photos or videos are to be recorded in
motion detection mode. In "Cam + Video" mode, the camera
first takes a photo and then starts filming video.
In “Camera” mode the menu options ”Video Size” and ”Video
Length” are unavailable; And in “Video” mode the menu
options ”Photo Size” and ”Picture No.” are unavailable.
Language:
Here you can change the language from English to Chinese, German, Finnish, Swedish, Danish,
French, Czech, Norwegian, Slovak, Russian, Italian, Spanish or Portuguese etc.
Photo Size:
Select a photo size in megapixels: 1 MP, 3 MP, 5 MP (default), 8 MP, 12MP. The larger the file size,
the more detailed the image.
Video Size:
Select the screen resolution: 1280 × 720, 720 × 480, 640 × 480 or 320 × 240. The higher the
resolution, the sooner the capacity limit of the memory card will be reached.
Photo No.:
Like a photo burst you can select the number of photos that are to be taken in succession when the
camera is activated in photo mode. In addition to single shot mode (01 photo), you can take 2 photos
in series (02 photo) or 3 photos in series (03 photo).
Video Length:
Videos are in AVI format that can be played back on most video players. Use the / buttons to
select the length of the video recording (between 3 seconds–10 minutes) that is to be made when
video recording is activated. The longer the recording time selected, the shorter the operating time.
Important note: Recording of video is highly demanding on battery power and triply so for night
vision recording as the camera must operate an invisible infrared torchlight at night. Longer length
recordings and or high frequency of recordings will lead to short battery operating times.
Photo size
Resolution
8GB SD card max photo capacity
1M
33926
3M
13252
5M
8274
8M
5217
12M
3474
Video size
Resolution
(Home Screen)
Resolution
(image size)
8GB SD card video storage
capacity max
(hours:minutes:seconds)
QVGA
320x240
3:12:45
VGA
640x480
1:34:56
D1
720x480
1:10:40
720P
1280x720P
0:53:00
Functions Explained (cont.)

Interval:
Use the / buttons to select the minimum time period that the camera should wait before
reacting to subsequent activation of the main sensor after the initial recording. During the selected
interval, the camera will not record any images or videos. Longer interval times preserve battery
life and prevent the memory card from being filled up with too many recordings of the same event.
You can select between 5–59 seconds or 1–60 minutes.
Sense Level:
The sensitivity of the main motion sensor is set here. Sensitivity sets a threshold of what can be
interpreted as movement to trigger the camera. There is a dynamic connection between the size
of the moving object and distance from the camera. Low sensitivity may allow for some small
environmental movements to be ignored but can then mean that person may need to be a little
closer to the camera to trigger it. In the same way high sensitivity could allow for smaller objects or
movements to trigger the camera. Consider the below examples and adjust accordingly when
testing your set-up.
For interior areas and environments with little interference, such as branches blowing in the wind,
select "High". Select "Normal" for exterior areas and environments with a normal amount of
interference and select "Low" for environments with a high level of interference. The temperature
can also affect the sensitivity. The "High" setting is suitable for warm ambient temperatures,
whereas "Low" should be selected for cold environments.
The general rule of thumb is the motion detection range is 20m however a large moving object at
greater distance may trigger the camera. A large temperature differential may trigger the camera
such as a heating vent or ground shadow if there is a large moving temperature contrast in view.
Set Date & Time:
Here you can set the time and date. Use the / buttons to switch between the values and
change the selected value with the / buttons. Confirm your settings with the OK button.
Date and time are displayed in the UAS format Year/Month/Day Hours: minute (with hours in 24Hr
time)
It is important to set the correct details as it effects the accuracy of the date stamp to photos, the
timer function and the date/time of images is also written against the file details on the memory
card (visible when reviewing files on a PC).
Date Stamp:
Here you can choose whether to save your photos with a time stamp.
Date, Time, Temperature, Moon Phase will be stamped on the photos and videos if you choose
“Date/Time”.
Functions Explained (cont.)
Distance from Camera
Near Far
Sensitivity required to trigger camera
Low High
Chance of detecting movement
High Low
Size of object / size of movement
Small Large
Chance of detecting movement
Low High
Sensitivity required to trigger camera
High Low